• 한국광학회:학술대회논문집
• /
• 한국광학회 2001년도 제12회 정기총회 및 01년도 동계학술발표회
• /
• pp.156-157
• /
• 2001

전계 흡수 광 변조기는 우수한 소광비와 낮은 전력 소모로 넓은 대역폭을 확보할 수 있으며 LD와의 단일 집적인 EML(electro-absorption modulator integrated laser diode)의 제작도 용이하므로 Microwave-Photonics 시스템에 매우 적합한 소자로써 근래에 활발한 연구가 진행되어지고 있다. 전계 흡수 광 변조기의 대역폭을 최대한 확보하기 위해서는 진행하는 마이크로파의 위상속도와 광파의 그룹 속도가 정합 되어야 하며 소자의 임피던스가 50Ω에 정합 되어야 한다. (중략)

• 한국결정학회지
• /
• 제14권1호
• /
• pp.25-31
• /
• 2003

가속된 전자가 전자파의 원이다. 전자가 가속운동을 하면 그 전자에 의한 전장도 가속운동을 한다. 이 변하는 전장은 변하는 자장을 만들고 변하는 자장은 변하는 전장을 만드는 이 과정이 스스로 영구 반복된다. 이렇게 서로 연관되어 생성된 B와 E의 선들은 폐쇄된 loop들을 형성하면서 그 파원으로부터 속력 c로 멀어져 가는데 이 전장 및 자장을 전자파라 한다. 전자파의 모든 성질은 Maxwell의 식에서 수학적으로 추론된다.

• 오토저널
• /
• 제15권3호
• /
• pp.47-54
• /
• 1993

This paper describes briefly the effect of ultrasonic fuel supply device on the performance of four stroke cycle gasoline engine. Experiments were carried out to clarify the effect of ultrasonic fuel supply device on the engine output, traveling fuel consumption ratio, exhaust emissions. The results were obtained as follows: 1.Engine output was increased 9-14% in comparison with that of the conventional injector. 2.Travelling fuel consumption ratio was improved 17-29% in comparison with that of the conventional injector. 3. CO, HC exhaust emissions was decreased compared to the value of the conventional injector. 4.Fuel consumption ratio in highway driving test was improved about 10% in comparison with that of the conventional injector.

• ETRI Journal
• /
• 제28권5호
• /
• pp.648-651
• /
• 2006

In this letter we present a right-angle-bent coplanar waveguide (CPW) which we developed for the application of the driver amplifier-integrated (DAI) 40 Gbps traveling wave electroabsorption modulated laser module. The developed CPW realized parallel progression of the radio frequency (RF) and light using a dielectric overlay structure and wedge bonding on the bending section. The measured $S_{11}$ and $S_{21}$ of the developed CPW were kept below-10 dB up to 35 GHz and -3 dB up to 43 GHz, respectively. These measured results of the CPW were in good agreement with the simulation results and demonstrated the applicability of the CPW to the 40 Gbps communication module.

• Journal of Electrical Engineering and Technology
• /
• 제8권2호
• /
• pp.262-270
• /
• 2013

A boundary protection method for power distribution line based on equivalent boundary effect is presented in this paper. In the proposed scheme, the equivalent resonance component with a certain central frequency is sleeve-mounted at the beginning of protected zone. The 'Line Boundary' is built by using boundary effect, which is created by introducing impedance in the primary-side of line. The 'Line Boundary' is significantly different from line wave impedance. Therefore, the boundary protection principle can be applied to power distribution line without line traps. To analyze the frequency characteristic corresponding to traveling-waves of introducing impedance in the primary-side of line, distributed parameters model of equivalent resonance component is established. The results of PSCAD/EMTDC simulation prove the obvious difference of voltage high frequency component between internal faults and external faults due to equivalent resonance component, and validate the scheme.

• Journal of Power Electronics
• /
• 제16권3호
• /
• pp.915-924
• /
• 2016

A digital self-sustained phase shift modulation (DSSPSM) strategy that allows for good soft switching and dynamic response performance in the presence of step variations is presented in this paper. The working principle, soft switching characteristics, and voltage gain formulae of a LLC converter with DSSPSM have been provided separately. Furthermore, the method for realizing DSSPSM is proposed. Specifically, some key components of the proposed DSSPSM are carefully investigated, including a parameter variation analysis, the start-up process, and the zero-crossing capture of the resonant current. The simulation and experiment results verify the feasibility of the proposed control method. It is observed that the zero voltage switching of the switches and the zero current switching of the rectifier diodes can be easily realized in presence of step load variations.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.282-285
• /
• 1999

Fabrication and pakaging method for low delve voltage and 10Gbps Ti diffused waveguide LiNbO$_3$ optical intensity modulator are described. Optical waveguides were prepared by conventionaly electron-beam evaporation and Ti-indiffusion into Z-cut plate LiNbO$_3$. Traveling-wave electrodes were used for obtaining the wideband frequency response and impedance matching. Microwave effective index and characteristic impedance measured by time domain reflectometry and compared with the calculated value by conformal mapping. The characteristics of 10Gbps modulator at the 1550nm wavelength are as follows : perfect modulation voltage Is about 5V, optical insertion loss Is about 5dB, 3-dB bandwidth is 10GHz, and characteristic impedance is about 50$\Omega$.

• 대한전기학회논문지:전력기술부문A
• /
• 제52권12호
• /
• pp.713-721
• /
• 2003

This paper analyzes the switching overvoltage occurred on 345kV underground power cable system as well as combined transmission system using EMTP. Cable length and closing time, preinsertion resistance have effect on switching overvoltage. Therefore, this paper analyzes the switching overvoltage occurred on conductor and sheath with change of those parameters. Specially, the cross bonding position becomes discontinuity point because of the difference between surge impedance of metal sheath and that of lead cable. Thus, the transmission and the reflection of traveling wave complexly occur at this connection point. According to these influences, voltage between sheath and earth as well as voltage between joint boxes rise. Time to crest point of switching overvoltage is longer than lightning overvoltage. Even though the voltage induced by switching surge is smaller than lightning surge, that voltage may have serious effect on the metal sheath. Therefore, this paper also analyses the reduction effect of switching overvoltage when the preinsertion resistance of circuit breaker is considered.

• ETRI Journal
• /
• 제28권3호
• /
• pp.393-396
• /
• 2006

This letter proposes a new impedance matching scheme of a traveling wave electro-absorption modulator (TWEAM) module for a 60 GHz band radio-over-fiber (ROF) link. A microstrip band pass filter (BPF) was used to achieve impedance matching at the 60 GHz band, and termination resistance was carefully designed to obtain an input impedance close to $50\;{\Omega}$. Also, a bias circuit for the device was designed in the module. The measured return loss and frequency response show that the modulator module observes the characteristics of a filter without the need of a further tuning process.

• 한국군사과학기술학회지
• /
• 제13권3호
• /
• pp.378-387
• /
• 2010

In this paper, we present new structure of wideband parabolic gain equalizer for TWT applied to printed circuit board. The gain equalizer is manufactured by using design variables of transmission line obtained from derived formulae. We compared the test results of two equalizers(reference equalizer and our equalizer). From that, we confirmed the validity of presented method. The presented equalizer is 1/3 times lighter, 1/2.7 times smaller and 1/10 times chipper than those of reference equalizer(Inmet company), respectively.