• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제5B권2호
• /
• pp.137-141
• /
• 2005

A transverse flux, PM-exited linear motor (TFM-LM) with inner mover was designed and built. Its output power density is higher and its weight is lower than those of the conventional PM exited linear synchronous motors (PM LSM). To obtain the maximum thrust force under the given volume, the thrust force density with respect to the ratio of the slot width and the length of pole pitch is analyzed by the 3-dimension finite element method (FEM). Finally, calculated static thrust forces was compared with the experimental values. The calculated and measured performance of the transverse flux, PM-exited linear motor with inner mover revealed great potential for system improvements by reducing the mass of the linear motor. For examples, when this motor was applied to a ropeless elevator, it was possible to increase the power density by more than 400% over the conventional PM-LSM. The results of this study recommend this type of motor for the ropeless elevator or gearless direct linear driving system.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권1호
• /
• pp.16-20
• /
• 2006

The proposed paper presents an integrated linear actuator which combines Transverse Flux Linear Motor(TFLM) for Household elelctric applications. They both use the same primary magnetic circuit, but they have different secondary movers. The paper presents a new design of linear motor for a new electromagnetic linear actuator, an tintegrated TFLM. The calculated tthrust force is good agreement with experiments. We have studied a transient response of a linear actuator with a damping ratio, spring constant and specially a pressed power patterns for a constant stroke control.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권1호
• /
• pp.16-23
• /
• 2004

Permanent magnet-excited transverse flux linear motor(TFLM) is known to have more excellent ratio of force to weight than any other linear motors. But, thrust generated by phase current is non-linear with regard to current and relative position like switched reluctance motor. This makes current and speed controller design difficult. This paper presents a method on minimization of thrust ripple of permanent magnet-excited transverse flux linear motor. Using genetic algorithm(GA), optimal current waveform can be found under the constraint conditions such as current limit, minimum of ohmic loss and limited rate of change of current etc. The effectiveness is verified through computer simulation and experimental test results.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권3호
• /
• pp.145-151
• /
• 2000

The topological investigations regarding magnetic circuit geometry and winding form of the transverse flux machine have brought up a variety of constructable arrangements with different features for several types of application[1, 2]. Here with, a novel PM-exited linear motor with inner mover, based on the transverse flux configuration leads to a considerable increase in power density for moving part. In this study we designed PM-exited transverse flux linear motor for ropeless elevator, whose output power density is higher and weight is lighter than conventional linear synchronous motors. When the designed motor in this study is applied to ropeless elevator, it is possible to increase power density more than 400% comparing with PM exited linear synchronous motor. The result of this study can be utilized for ropeless elevator or gearless direct linear moving system with high output[3].

• Journal of Magnetics
• /
• 제16권1호
• /
• pp.58-63
• /
• 2011

This paper presents design procedures of a transverse flux linear motor (TFLM). The minimum and maximum flux linkage was determined by the simplified equivalent magnetic circuit and estimated average magnetic flux density at the air gap region by considering the shape of applied magnetomotive force (MMF). With this information, the number of turns of each phase winding was calculated based on the amplitude of applied voltage and speed of a mover. The rated current, coil diameter, and winding area were obtained with the aid of an empirical formula for determining the required MMF. The usefulness of the proposed design method for TFLM is verified by the three-dimensional equivalent magnetic circuit network (EMCN) method and the experimental results of prototyped machine.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.997-1000
• /
• 1993

This paper proposes the linear induction motor with salient poles, transverse flux and the secondary aluminum conductor for a new type urban MAGLEV. Compared with the more usual kind of linear induction motor with longitudinal flux, TFLIM have flux paths tying transversely to the direction of motion. This shortens the magnetic circuit and produces the thrust, the attraction force and the lateral stabilization force simultaneously. Owing to these electrodynamic force, TFLIM will be usable to a new type urban MGLEV.

• 전기학회논문지
• /
• 제59권3호
• /
• pp.562-568
• /
• 2010

In this paper, a low cost magnetic position sensor for linear position detection is proposed. The proposed magnetic sensor can be applied to the linear motor which has stator with periodical teeth, such as transverse flux linear motor(TFLM). Sine and cosine waves can be generated from the unit sensor module as the linear motor moves, and the outputs can be converted to the position data by interpolation IC. To reduce the speed ripple caused by the position error, the Luenberg observer is introduced. The validity of the proposed magnetic position sensor is verified by experiment with a 750N three-phase TFLM.

• 전기의세계
• /
• 제23권4호
• /
• pp.39-45
• /
• 1974

In most previous research work, the transverse edge effect has been allowed for only by use of a relativity-increase factor. This paper gives a more exact treatment. A two-dimensional-field analysis is presented for the problem of sheet rotor linear induction motor with finite width the method used takes account of flux leakage in the space between the stator and secondary sheet rotor as well as in the secondary itself. Equations are derived for the flux density distribution in the air gap and for the starting face, in each case as a function of stator current. The cross gap flux density peaks towards athe edge of the stator. This phenomena is known as the transverse edge effect. Measurements of the flux density in the air gap and starting force on a linear induction motor with sheet rotor of different width showed a reasonable agreement,suggest that it would be desirable to take into account also, at least for this motor in which severe redistribution occurs.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권2호
• /
• pp.102-109
• /
• 2000

The magnetically levitated system technology is highly expected to contribute the new transportation system of the 21st century with its high velocity operation, better riding comforts, friendliness to environment and saving of maintenance labour. Its development has been completed in low speed and in high speed application. In 2005, the Transrapid with 430 km/h speed will go into operation between Berlin and Hamburg[1]. In the year 2000, the realization of JR-Maglev will be basically evaluated for commercial operation[2]. In korea, maglev test vehicle with magnet for levitation and single sided linear induction motor for propulsion is under test at 1 [km] test track in KIMM.[3,4] Here, a transverse flux linear motor in combination with the levitation and the guidance leads to a considerable high power density and high efficiency simultaneously. The designed and measured performance of transverse flux linear motor for maglev system revealed a great potential of system mass reduction.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 A
• /
• pp.43-45
• /
• 1999

This paper is presented about the development of magnetic levitation conveyor with a transverse flux linear synchronous motor (TFLSM). The TFLSM is proposed as the new type linear motor for the conveyor driving system. The flux density distribution. the thrust and etc. of TFLSM are analyzed by the finite element method. To analyze the dynamic characteristics of TFLSM, the parameter of equivalent circuit is calculated by the analytical method.