• Journal of the Korean Ceramic Society
• /
• v.43 no.10 s.293
• /
• pp.635-639
• /
• 2006

Dispersion behavior of the slurries consisted of Pb or Bi-based glass frits, which are used for the fabrication of green sheet as PDP front panel transparent dielectric, was examined in non-aqueous solvent system. Measurements of sedimentation height and viscosity were conducted to determine proper dispersion condition in the various solvent and dispersant system. Azotropic compound and ethyl acetate were used as the solvent and ammonium-type dispersant was applied to the slurries. All slurries were dispersed well in azotropic solvent system involving 20$\sim$50 vol% ethyl acetate at 2$\sim$3 wt% dispersant content. Especially, dispersion behavior was notably improved in the addition of ethyl acetate in the Bi-based frit slurry.

• Journal of the Korean Ceramic Society
• /
• v.28 no.4
• /
• pp.324-328
• /
• 1991

Monolithic silica gel and glass were prepared from TMOS solution with high concentration of HCl. Appearance of the dried gels and gelation time varied with content of HCl and H2O were observed in the TMOS-CH3OH-HCl-H2O system. The conversion from gel to glass during heat treatment stage was investigated using TG-DTA, XRD, IR and SEM and characteristics of the gel were examined by measuring bulk density, linear shrinkage and Vicker's hardness. A transparent silica glass was prepared from the gel after heat treatment at 1050℃.

• Journal of the Korean Ceramic Society
• /
• v.44 no.10
• /
• pp.548-553
• /
• 2007

Ceramic green sheets consisting Bi-based glass frit were fabricated for an application to PDP transparent dielectric front panel. The dispersion condition of the slurry for tape casting was pre-examined, and two kinds of hinder and plasticizer were used in the non-aqueous slurry system. In the fabrication process for the frit film, the properties such as dry and firing shrinkage, elongation, and transmittance were examined at the condition of various mixing ratio of plasticizers. In the mixing ratio of polyethylene glycol to dibutyl phthalate of 3:5wt%, a good adhesion, elongation and transmittance were observed at the firing temperature of $580^{\circ}C$. The photograph for the cross section of the interface was also showed a dense microstructure.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2004.04b
• /
• pp.47.1-47.1
• /
• 2004

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.2
• /
• pp.275-285
• /
• 1996

The effect of heat-treatment on catalytic crystallization in $LI_2O-Al_2O_3-SiO_2$ glass system over its glass transition temperature was investigated. Glass composition $4Li_2O{cdot}22AL_2O_3{cdot}66SiO_2{cdot}2TiO_2{cdot}2.5ZrO_2{cdot}1.5P_2O_5{cdot}1.0Na_2O{cdot}1.0As_2O_3$ (wt%) was selected and heat-treated at different heating conditions to obtain transparent glass-ceramic. Nucleation and crystallization behaviour of this composition were estimated by differential thermal analysis (DTA) and X-ray diffractometer (XRD) and its thermal expansion coefficients were measured by Dilatometer. As a result, glass transition temperature was $730^{\circ}C$ and two maximum nucleation temperatures were estimated at $730^{\circ}C$ and 82$0^{\circ}C$ using JMA(Johson-Mehl-Avrami) equation by DTA. $ZrTiO_4$ $\beta$-Quartz solid solution and $\beta$-Spodumene crystals were identified by XRD. The optimum crystallization temperature was 92$0^{\circ}C$ and three step heating schedule was expected to be useful to obtain transparent glass-ceramic.

• The Korean Journal of Ceramics
• /
• v.2 no.1
• /
• pp.1-10
• /
• 1996

Transparent conducting $SnO_2$-based thin films have been coated on float substrates such as fused quartz, and ceramic fiber cloths such as the Nexel and E-glass cloth from tin alkoxides by the sol-gel technique. Also, thin films of alternating layers of $SnO_2$ and $SiO_2$ have been fabricated by dip coating. The sheet resistance and average visible transmittance of the films were investigated in the aspect of the applications as transparent electrodes such as liquid crystal displays, photo-detectors and solar cells. The Nextel and E-glass cloths coated with antimony-doped tin oxide (ATO) had sheet resistance of as low as $20 \;ohm/{\Box}$ and $120ohm/\;{\Box}$, respectively. The promotion effects of additives as $La_2O_3$ and Pt on the ethanol gas sensing properties of the films were investigated in the aspects of the applications as an alcohol sensor and a breath alcohol checker. Possible evidence of quantum well effects in the oxide multilayers of $SnO_2$ and $SiO_2$ was investigated.

• Journal of the Korean Ceramic Society
• /
• v.31 no.4
• /
• pp.436-447
• /
• 1994

ZnO transparent conducting thin film, which is a strong candidate for a transparent electrical contact in optoelectronic devices, was prepared by the vapour spraying method on the slide glass in nitrogen ambient at the atmospheric pressure. The structural, optical and electrical properties of films show a strong dependence on substrate temperature, and the optimum range of deposition temperature existed to obtain TCO(Transparent Conducting Oxide) films. At the higher temperatures, milky films were obtained. In such optimum range, the bandgap in ZnO films was determined from the spectral dependence of absorption coefficient and electrical characteristics were characterized with by the Hall mobility and carrier concentration.

• Journal of the Korean Ceramic Society
• /
• v.52 no.4
• /
• pp.290-293
• /
• 2015

The properties of the IZTO thin films on the glass were studied with a variation of the $SiO_2$ buffer layer thickness. $SiO_2$ buffer layers were deposited by plasma-enhanced chemical vapor deposition (PECVD) on the glass, and the In-Zn-Tin-Oxide (IZTO) thin films were deposited on the buffer layer by RF magnetron sputtering. All the IZTO thin films with the $SiO_2$ buffer layer are shown to be amorphous. Optimum $SiO_2$ buffer layer thickness was obtained through analyzing the structural, morphological, electrical, and optical properties of the IZTO thin films. As a result, the IZTO surface roughness is 0.273 nm with a sheet resistance of $25.32{\Omega}/sq$ and the average transmittance is 82.51% in the visible region, at a $SiO_2$ buffer layer thickness of 40 nm. The result indicates that the uniformity of surface and the properties of the IZTO thin film on the glass were improved by employing the $SiO_2$ buffer layer and the IZTO thin film can be applied well to the transparent conductive oxide for display devices.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.1
• /
• pp.43-52
• /
• 2010

Glass was fabricated by using refused coal ore obtained from Dogye coal mine in Samchuk. We additionally used soda ash and calcium carbonate as raw materials to make a glass with the chemical composition of soda-lime glass. And the properties of glass were measured when limestone was used as natural raw materials instead of calcium carbonate as chemical raw materials. Transparent glass was fabricated by melting raw materials at $1550^{\circ}C$ for 1 hr in an electrical furnace. The various kinds of glass samples were fabricated according to the kinds of refused coal ore and glass cullet. The optical properties of transmittance and color chromaticity were measured by UV/VIS/NIR spectrometer and the thermal properties of thermal expansion coefficient and softening point were measured. Transparent glass with the transmittance of over 70% in visible range was fabricated by using normal refused coal ore and black colored glass with the transmittance of 0~35% was fabricated by using shel1 type refused coal ore. Therefore, it is concluded that refused coal ore can be used for raw materials to manufacture secondary glass products such as a glass tile and foamed glass panel for construction material.

• Journal of the Korean Ceramic Society
• /
• v.27 no.2
• /
• pp.288-296
• /
• 1990

Parent glasses for the experiments were prepared to be ratio of Li2O : Al2O3 : SiO2=4.5 : 25 : 70.5 as basic components, and TiO2 and ZrO2 in the mixing ratio of 1 : 1 were added as the nucleating agents, whose contents were increased in each sample. DTA, XRD, SEM, IR were observed, and thermal expansion and transmissivities were measured for the crystallized samples under the controlled heat-treatments. The transformation temperatures and the dilatometric softening temperatures in thermal expansion curves, and also the exothermic peaks in differential thermo-analytical curves were shifted to lower temperature. The crystal phase deposited through the heat-treatment was identified as ${\beta}$-quartz solid solution with XRD and IR analysis. The crystalline phases in oopactified samples were ${\beta}$-spodumene coexiting with ${\beta}$-quartz solid solution. The samples having more than 3% nucleating agents were transparent. The crystallized grain sizes were ranged 0.05 to 0.1$\mu\textrm{m}$. The crystallized transparent samples were exceeded 85% in the transmissivity.