• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.8
• /
• pp.1248-1256
• /
• 2008

In this paper, basic characteristics of transmission line employing PPGM (periodically perforated ground metal) were investigated using theoretical and experimental analysis.According to the results, unlike the conventional PBG (photonic band gap) structures, the characteristic impedance of the transmission line employing PPGM structure showed a real value, which exhibited a very small dependency on frequency. The transmission line employing PPGM structure showed a loss (per quarter wave length) higher by $0.1{\sim}0.2\;dB$ than the conventional microstrip line. According to the investigation of the dependency of RF characteristic on ground condition, the RF characteristic of the transmission line employing PPGM structure was hardly affected by the ground condition in the frequency lower than Ku band, but fairly affected in the frequency higher than Ku band, which indicated that coplanar waveguide employing PPGM structure was optimal for RF characteristic and reduction of size. Considering above results, impedance transformer was developed using coplanar waveguide with PPGM structure for the first time, and good RF characteristics were observed from the impedance transformer. In case that {\lambda}/4$ impedance transformer with a center frequency of 9 GHz was fabricated for a impedance transformation from 20 to10 {\Omega}$, the line width and length were 20 and $500\;{\mu}m$, respectively, and its size was only 0.64 % of the impedance transformer fabricated with conventional microstrip lines. Above results indicate that the transmission line employing PPGM is a promising candidate for a development of matching and passive elements on MMIC.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.468-471
• /
• 2000

This paper investigates the harmonics of TCSC power transmission system having nonlinear VI characteristic loads. Nonlinear VI characteristic components are modelled with Nortons harmonic current sources. The system parameters such as line impedances admittances and node voltages and the thyristor switching action are described in complex Fourier series. EMTP simulation studies with a detailed three-phase TCSC power transmission system are also performed in order to verify the harmonic analysis at the steady state.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.10
• /
• pp.39-47
• /
• 1994

In this paper, by modeling the Multilayer-Multiconductor Transmission Line(MMTL) with the characteristic parameters-effective dielectric constant, eigen modal voltages, characteristic impedances at each mode, pulse propagation characteristics of MMTL network are simulated. Transmission line modelling is performed in frequency domain, then time domain resposes are obtained by transforming the frequency domain response using fast Fourier transform.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.6
• /
• pp.921-928
• /
• 1990

A multivariable equalizer is designed which compensates transmission distortion for coaxial transmission line. The characteristic transfer function with bilateral parameter domain is approximated using the expansion method of orthonormal function and Gram Schmidt orthogonal function, but the parameter domain of approximated function is limited to unilateral. To solve that problem, Bode type transfer function is used to give bilateral variable characteristic to approximated function. The multivariable equalizer in this paper can be substituted for the current equalizer which consist of a fixed equalizer and a variable equalizer.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.233-236
• /
• 2006

In this paper, I try to measure characteristic transmission-reflection by environmental change or solar cell. I keep my eye on the characteristics variation of solar cell as environmental change. As a result, A variation caused by voltage by an effect on the efficiency of solar PV cell. Hence, it is an important variable when a designer plan to make a solar cell.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.11 s.102
• /
• pp.1099-1105
• /
• 2005

TRL error correction method is widely used for measuring high frequency device mounted on PCB. In order to correct error more precisely, the characteristic impedance of standard transmission line should be known mounted for error correction. The capacitance per the unit length of transmission line is calculated by using standard transmission line which terminate resistor additionally at previous method and the characteristic impedance of standard transmission line is calculated with fitting method according to frequency, but the characteristic impedance extracted by a manufacturing inaccuracy is influenced. In this study, a novel method can reduce the manufacturing inaccuracy using measured s-parameters and can extract more accurate characteristic impedance than the previous method.

• The KSFM Journal of Fluid Machinery
• /
• v.13 no.6
• /
• pp.77-82
• /
• 2010

This study has conducted numerical analysis for lubrication system of transmission for commercial vehicle. The lubrication oil system in transmission can be applied to a large scale commercial vehicle which is over 15tons. The flow rate of lubricating oil has been obtained for each of branch port from the lubrication pipe. The results from numerical simulation are mainly suggested for the mass flow rate of lubrication oil in the rotating main shaft of transmission system. It has been found that the mass flow rate from oil hole increased with an rotating rate of main shaft. The flow characteristic from oil hole has been presented for the lubricating system in the manual transmission.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.4 no.2
• /
• pp.122-129
• /
• 2001

A characterization procedure for analyzing symmetric coupled MIS(Metal-Insulator-Semiconductor) transmission line is used the same procedure as a general single layer symmetric coupled line with perfect dielectric substrate from the extraction of the characteristic impedance and propagation constant for even- and odd-mode. In this paper, an analysis for a new substrate shielding symmetric coupled MIS structure consisting of grounded crossbar at the interface between Si and SiO2 layer using the Finite- Difference Time-Domain(FDTD) method is presented. In order to reduce the substrate effects on the transmission line characteristics, a shielding structure consisting of grounded crossbar lines over time-domain signal has been examined. Symmetric coupled MIS transmission line parameters for even- and odd-mode are investigated as the functions of frequency, and the extracted distributed frequency- dependent transmission line parameters and corresponding equivalent circuit parameters as well as quality factor for the new MIS crossbar embedded structure are also presented. It is shown that the quality factor of the symmetric coupled transmission line can be improved without significant change in the characteristic impedance and effective dielectric constant.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.6
• /
• pp.964-973
• /
• 2008

In this study, a short-wavelength coplanar-type transmission line employing periodic ground structure (PGS) was developed for application to miniaturized on-chip passive component on Si Radio Frequency Integrated Circuit (RFIC). The transmission line employing PGS showed shorter wavelength and lower characteristic impedance than conventional coplanar-type transmission line. The wavelength of the transmission line employing PGS structure was 57 % of the conventional coplanar-type transmission line on Si substrate. Using the theoretical analysis. basic characteristics of the transmission line employing PGS (e.g., bandwidth. loss, impedance, and resonance characteristics) were also investigated in order to evaluate its suitability for application to a development of miniaturized passive on-chip components on silicon RFIC. According to the results. the bandwidth of the transmission line employing PGS was more than 895 GHz as long as T is less than 20${\mu}m$, and the resonance characteristic was observed in 1239 GHz, which indicates that the PPGM structure is a promising candidate for application to a development of miniaturized on-chip passive components on Si RFIC.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.2
• /
• pp.349-355
• /
• 2009

As electrical power demand is gradually increasing, the construction of power transmission facility is unavoidable. However difficulties which resulted from increasing of complaints and NYMBY make power transmission tower to be more environmentally friendly. As an alternative proposal, a new method which is changing conventional iron arm for insulation arm which is made of FRP(Fiber Glass Reinforced Plastics) is in progress. In this paper, we discussed environmentally friendly characteristic of domestic 154 kV testing transmission tower whose insulation arms have same mechanical and excellent electrical properties compare to conventional heavy iron arm.