• 한국소음진동공학회논문집
• /
• 제23권10호
• /
• pp.920-927
• /
• 2013

The requirement of acoustic performance about underwater acoustic material which is used in underwater environment more increases. Underwater acoustic material was made by viscoelastic material such as a rubber and a polyurethane etc. In order to increase an acoustic performance, several kinds of inclusions were added to viscoelastic material. In this paper, acoustic modelling and analysis techniques were introduced and the acoustic characteristics of underwater acoustic material were studied. Echo reduction and transmission loss were calculated with volume fraction of inclusion in the material. Also the characteristic impedance and the input impedance of underwater acoustic material were obtained and effects on the echo reduction and transmission loss of material were discussed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 A
• /
• pp.31-33
• /
• 2000

This paper discusses the operational characteristic analysis of distance relay depending on the power system parameters in transmission line including FACTS devices. Distance relay requires protective coordination because the FACTS devices change power system parameters to increase power transmission capacity. In this paper, the dynamic operational characteristics of distance relay are analyed for the effect of fault resistance and operation mode of FACTS devices according to the installed points of these devices.

• 대한전기학회논문지:전력기술부문A
• /
• 제51권10호
• /
• pp.525-533
• /
• 2002

It is common to install multiple lines in the same route. Recently, excessive sheath circulating current was partially measured in underground cable systems of KEPCO. Especially, the installation type, unbalance section length between joint boxes and zero sequence current by distribution cable have an effect on the rising of sheath circulating current in the underground transmission system. If excessive current flows in sheath, sheath loss which is reduced the transmission capacity is produced. This paper describes the relation analysis of sheath circulating current and burying types. And also, a detailed analysis on rising cause and characteristic of sheath circulating current by considering various unbalanced conditions presents using analysis and measurement regarding cable systems which have the problem of excessive sheath circulation current.

• Journal of electromagnetic engineering and science
• /
• 제9권2호
• /
• pp.85-97
• /
• 2009

As operating frequency is raised and as more integration with active and passive elements is required, it becomes difficult to fabricate more than 120 ${\Omega}$ characteristic impedance of a mierostrip line. To solve this problem, an equivalent high impedance transmission-line section is suggested, which consists mainly of a pair of coupled-line sections with two shorts. However, it becomes a transmission-line section only when its electrical length is fixed and its coupling power is more than half. To have transmission-line characteristics(perfect matching), independently of coupling power and electrical length, two identical open stubs are added and conventional design equations of evenand odd-mode impedances are modified, based on the fact that the modified design equations have the linear combinations of conventional ones. The high impedance transmission-line section is a passive component and therefore should be perfectly matched, at least at a design center frequency. For this, two different solutions are derived for the added open stub and two types of high impedance transmission-line sections with 160 ${\Omega}$ characteristic impedance are simulated as the electrical lengths of the coupled-line sections are varied. The simulation results show that the determination of the available bandwidth location depends on which solution is chosen. As an application, branch-line hybrids with very weak coupling power are investigated, depending on where an isolated port is located, and two types of branch-line hybrids are derived for each case. To verify the derived branch-line hybrids, a microstrip branch-line hybrid with -15 dB coupling power, composed of two 90$^{\circ}$ and two 270$^{\circ}$ transmission-line sections, is fabricated on a substrate of ${\varepsilon}_r$= 3.4 and h=0.76 mm and measured. In this case, 276.7 ${\Omega}$ characteristic impedance is fabricated using the suggested high impedance transmission-line sections. The measured coupling power is -14.5 dB, isolation and matching is almost perfect at a design center frequency of 2 GHz, showing good agreement with the prediction.

• 대한전자공학회논문지
• /
• 제19권1호
• /
• pp.29-34
• /
• 1982

U형 수준선의 특성임피던스는 유한차분법에 의해서도 계산될 수 있으나 이 연구에서는 모먼트법에 의하여 그의 특성 임피던스를 계산한다. 유한차분법에 의한 계산결과와 모먼트법에 의한 결과에는 10%정도의 차가 좌우한다. 그러나 내부도체가 외부도체의 중앙에 있을 때 모먼트법에 의한 결과는 선석적인 방법에 의한 결과와 거의 일치된다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 A
• /
• pp.494-496
• /
• 2001

This paper describes sheath induced voltage and operating characteristic of cable cover protection unit(CCPU) in underground transmission cable. Real cable system operating by 154kV XLPE cable was modelled for simulation. Sheath induced voltage and operating characteristic of CCPU were analyzed. In particular, sheath induced voltage was analyzed in case of individual grounding and common grounding, respectively, and operating characteristics of CCPU were compared each other.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권2호
• /
• pp.330-335
• /
• 2008

In this study, highly miniaturized short-wavelength transmission line employing periodically perforated ground metal (PPGM) structures were developed for application to miniaturized on-chip passive component on Si RFIC. The transmission line employing PPGM structure showed shorter wavelength and lower characteristic impedance than conventional coplanar-type transmission line. The wavelength of the transmission line employing PPGM structure was 57% of the conventional coplanar-type transmission line on Si Radio Frequency Integrated Circuit (RFIC) substrate. Basic characteristics of the transmission line employing PPGM structure were also investigated in order to evaluate its suitability for application to a development of miniaturized passive on-chip components. According to the results, it was found that the PPGM structure is a promising candidate for application to a development of miniaturized on-chip passive components on Si RFIC.

• Journal of Power Electronics
• /
• 제12권4호
• /
• pp.519-527
• /
• 2012

A high step-down multiple-output LED driver is proposed in this paper. Firstly, the derivation of the driver with dual-output is presented and its operation principle and steady state performance are analyzed in detail. Secondly, a high step-down N-channel LED driver is proposed and its current auto-balance characteristic and step-down ratio are analyzed. Finally, an experimental prototype is built and the experimental results are given. The theoretical analysis and experimental results show that the proposed driver has the following virtues: First, if load balancing is achieved, the voltage gain is 1/N that of a Buck driver, where N is the number of channels. Second, each output automatically has an equal output current, without requiring more current close-loop control circuits than a Buck driver. Last, the voltage stresses of the switches and diodes are lower than those of a Buck driver, meaning that lower voltage switches and diodes can be used, and a higher efficiency can be expected.

• 한국인터넷방송통신학회논문지
• /
• 제10권4호
• /
• pp.199-204
• /
• 2010

최근 전자 정보 통신 기술의 발전으로 개개인이 요구하는 정보의 전송량도 증가하고 있다. 특히 CATV의 전송량 증가에 따른 전송 성능의 향상이 불가피하다. 따라서 본 논문에서는 DOCSIS(Data-Over-Cable Service Interface Specifications) 2.0 요구 규격을 만족하는 CATV 전송 시스템에서 Bit Error Rate(BER)에 따른 최적의 Signal to Noise Ratio(SNR) 성능 요구 특성을 얻기 위한 위상 잡음 특성을 분석하였다. 특히 개발된 시뮬레이터를 이용하여 CATV 전송 시스템 위상 잡음 특성 요구 규격을 만족하는 Phase Locked Loop(PLL) 구성 요소 파라미터 값들을 도출하였다. 제시된 방법은 향후 초고속 CATV 전송 시스템의 위상잡음 관련 성능 요구 규격 도출에 이용될 수 있다.

• 대한전자공학회논문지TC
• /
• 제41권12호
• /
• pp.131-137
• /
• 2004

본 논문에서는 등각사상 법을 이용해 유전체가 다층으로 코팅된 평행 2선식 전송선로의 특성임피던스 및 유효 유전상수 등을 계산하는 방법을 제안하였다. 먼저 두께 및 유전상수가 다른 유전체가 임의의 N 층으로 코팅되었을 때 평행 2선식 전송선로의 정전용량을 계산하였으며, 이를 이용해 임피던스 및 유효 유전상수 등을 계산하였다. Ansoft 사의 Maxwell 2D를 이용한 시뮬레이션 결과와 비교하였을 때, 계산 결과가 오차범위 4% 이내로 거의 일치함을 알 수 있었다.