• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.10
• /
• pp.920-927
• /
• 2013

The requirement of acoustic performance about underwater acoustic material which is used in underwater environment more increases. Underwater acoustic material was made by viscoelastic material such as a rubber and a polyurethane etc. In order to increase an acoustic performance, several kinds of inclusions were added to viscoelastic material. In this paper, acoustic modelling and analysis techniques were introduced and the acoustic characteristics of underwater acoustic material were studied. Echo reduction and transmission loss were calculated with volume fraction of inclusion in the material. Also the characteristic impedance and the input impedance of underwater acoustic material were obtained and effects on the echo reduction and transmission loss of material were discussed.

• Proceedings of the KIEE Conference
• /
• 2000.07a
• /
• pp.31-33
• /
• 2000

This paper discusses the operational characteristic analysis of distance relay depending on the power system parameters in transmission line including FACTS devices. Distance relay requires protective coordination because the FACTS devices change power system parameters to increase power transmission capacity. In this paper, the dynamic operational characteristics of distance relay are analyed for the effect of fault resistance and operation mode of FACTS devices according to the installed points of these devices.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.51 no.10
• /
• pp.525-533
• /
• 2002

It is common to install multiple lines in the same route. Recently, excessive sheath circulating current was partially measured in underground cable systems of KEPCO. Especially, the installation type, unbalance section length between joint boxes and zero sequence current by distribution cable have an effect on the rising of sheath circulating current in the underground transmission system. If excessive current flows in sheath, sheath loss which is reduced the transmission capacity is produced. This paper describes the relation analysis of sheath circulating current and burying types. And also, a detailed analysis on rising cause and characteristic of sheath circulating current by considering various unbalanced conditions presents using analysis and measurement regarding cable systems which have the problem of excessive sheath circulation current.

• Journal of electromagnetic engineering and science
• /
• v.9 no.2
• /
• pp.85-97
• /
• 2009

As operating frequency is raised and as more integration with active and passive elements is required, it becomes difficult to fabricate more than 120 ${\Omega}$ characteristic impedance of a mierostrip line. To solve this problem, an equivalent high impedance transmission-line section is suggested, which consists mainly of a pair of coupled-line sections with two shorts. However, it becomes a transmission-line section only when its electrical length is fixed and its coupling power is more than half. To have transmission-line characteristics(perfect matching), independently of coupling power and electrical length, two identical open stubs are added and conventional design equations of evenand odd-mode impedances are modified, based on the fact that the modified design equations have the linear combinations of conventional ones. The high impedance transmission-line section is a passive component and therefore should be perfectly matched, at least at a design center frequency. For this, two different solutions are derived for the added open stub and two types of high impedance transmission-line sections with 160 ${\Omega}$ characteristic impedance are simulated as the electrical lengths of the coupled-line sections are varied. The simulation results show that the determination of the available bandwidth location depends on which solution is chosen. As an application, branch-line hybrids with very weak coupling power are investigated, depending on where an isolated port is located, and two types of branch-line hybrids are derived for each case. To verify the derived branch-line hybrids, a microstrip branch-line hybrid with -15 dB coupling power, composed of two 90$^{\circ}$ and two 270$^{\circ}$ transmission-line sections, is fabricated on a substrate of ${\varepsilon}_r$= 3.4 and h=0.76 mm and measured. In this case, 276.7 ${\Omega}$ characteristic impedance is fabricated using the suggested high impedance transmission-line sections. The measured coupling power is -14.5 dB, isolation and matching is almost perfect at a design center frequency of 2 GHz, showing good agreement with the prediction.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.19 no.1
• /
• pp.29-34
• /
• 1982

We can find the characteristic impedances of the U-type transmission lines by finite d ifference method. In this paper, the characteristic impedances of the lines are computed by the moment method. There are 10% differences between the results of the finite difference method and those of the moment method. But when the interior conductor of the line is located at the center of the exterior conductor, the results of the moment method approache to that of analytical result when the length of outer conductor becomes in finite.

• Proceedings of the KIEE Conference
• /
• 2001.07a
• /
• pp.494-496
• /
• 2001

This paper describes sheath induced voltage and operating characteristic of cable cover protection unit(CCPU) in underground transmission cable. Real cable system operating by 154kV XLPE cable was modelled for simulation. Sheath induced voltage and operating characteristic of CCPU were analyzed. In particular, sheath induced voltage was analyzed in case of individual grounding and common grounding, respectively, and operating characteristics of CCPU were compared each other.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.2
• /
• pp.330-335
• /
• 2008

In this study, highly miniaturized short-wavelength transmission line employing periodically perforated ground metal (PPGM) structures were developed for application to miniaturized on-chip passive component on Si RFIC. The transmission line employing PPGM structure showed shorter wavelength and lower characteristic impedance than conventional coplanar-type transmission line. The wavelength of the transmission line employing PPGM structure was 57% of the conventional coplanar-type transmission line on Si Radio Frequency Integrated Circuit (RFIC) substrate. Basic characteristics of the transmission line employing PPGM structure were also investigated in order to evaluate its suitability for application to a development of miniaturized passive on-chip components. According to the results, it was found that the PPGM structure is a promising candidate for application to a development of miniaturized on-chip passive components on Si RFIC.

• Journal of Power Electronics
• /
• v.12 no.4
• /
• pp.519-527
• /
• 2012

A high step-down multiple-output LED driver is proposed in this paper. Firstly, the derivation of the driver with dual-output is presented and its operation principle and steady state performance are analyzed in detail. Secondly, a high step-down N-channel LED driver is proposed and its current auto-balance characteristic and step-down ratio are analyzed. Finally, an experimental prototype is built and the experimental results are given. The theoretical analysis and experimental results show that the proposed driver has the following virtues: First, if load balancing is achieved, the voltage gain is 1/N that of a Buck driver, where N is the number of channels. Second, each output automatically has an equal output current, without requiring more current close-loop control circuits than a Buck driver. Last, the voltage stresses of the switches and diodes are lower than those of a Buck driver, meaning that lower voltage switches and diodes can be used, and a higher efficiency can be expected.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.4
• /
• pp.199-204
• /
• 2010

Recently, the transmission amount of information that each single person requires is growing by development of electron information communication technology. So in this paper we analysis the phase noise characteristics to obtain a most suitable of SNR performance request characteristic by BER on CATV transmission system that satisfy performance request DOCSIS 2.0 standard. Especially we get the parameter value of PLL that satisfy phase noise characteristic request standard using developed simulator. Presented method can be used to obtain a performance request standard connection performance request standard of high speed CATV transmission system in the future.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.12
• /
• pp.131-137
• /
• 2004

In this paper, we proposed the method of the characteristic impedance and effective dielectric constant calculations of a parallel-two-wire transmission line coated with multi-layer dielectric material using conformal mapping method. First of all, we calculated the capacitance of the transmission line when coated by N layer dielectric material which has different thickness and dielectric constant and calculated the characteristic impedance and effective dielectric constant using calculated capacitances. When compared with the Maxwell 2D (made by Ansoft Corporation) simulation result calculated result was very similar to the simulation result within the four percent error range.