• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.2
• /
• pp.99-105
• /
• 2022

As the chip size gets smaller, the width of the electrode line is also fine, and the density of interconnections is increasing. As a result, RC delay is becoming a problem due to the difference in resistance between the capacitor layer and the electrical conductivity layer. To solve this problem, the development of electrodes with high electrical conductivity and dielectric materials with low dielectric constant is required. In this study, we developed low dielectric ink by mixing commercial PSR which protect PCB's circuits from external factors and PI with excellent thermal property and low-k characteristics. As a result, the ink mixture of PSR and PI 10:3 showed the best results, with a dielectric constant of about 2.6 and 2.37 at 20 GHz and 28 GHz, respectively, and dielectric dissipation was measured at about 0.022 and 0.016. In order to verify the applicability of future applications, various line-width transmission lines produced on Teflon were evaluated, and as a result, the loss of transmission lines using low dielectric ink mixed with PI was 0.12 dB less on average in S21 than when only PSR was used.

• Korean Journal of Materials Research
• /
• v.10 no.9
• /
• pp.636-641
• /
• 2000

The effects of Fe and V content on the characteristics of $\beta$ to $\alpha$ phase transformation for Zr-0.8Sn alloys were studied by optical and transmission electron microscopy. With increasing V content, $\beta{\rightarrow}\alpha+\beta$ transformation temperature decreased, thus allowing the width of $\alpha$-lath to be fine air-cooled Zr-0.8Sn-xV alloys. The width of $\alpha$-lath, however, was slightly increased with Fe content. While the $\beta$ to $\alpha$ transformed microstructures of water-quenched Zr-0.8Sn, Zr-0.8Sn-0.1Fe, Zr-0.8Sn-0.2Fe, Zr-0.8Sn-0.4Fe, Zr-0.8Sn-0.1V and Zr-0.8Sn-0.2V were mainly slipped martensite, that of water-quenched Zr-0.8Sn-0.4V was predominantly twinned martensite. The transition of slipped martensite to twinned martensite in Zr-0.8Sn-Xv was thought to be due to the decrease of $M_S$ temperature.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.5B
• /
• pp.530-538
• /
• 2011

In this paper, the feasibility of LEO(low earth orbit) satellite-based automatic identification system (SAT-AIS) for the coastal area of the South Korea is evaluated in the context of ship AIS transmission detection probability. We evaluate and compare AIS signal detection probability of ORBCOMM satellites and LEO-one satellites considering link budget, SOTDMA protocol and satellite's swath width. The simulation determines the total number of vessels served by those satellites according to satellite's swath width and thus, By simulation results, the ORBCOMM SAT-AIS system outperforms LEO-one SAT-AIS system. The suggested ORBCOMM based SAT-AIS system can be a solution to resolve the existing limited transmission distance problem of the conventional ship-to-shore AIS system.

• Journal of the Korean Society for Railway
• /
• v.10 no.6
• /
• pp.650-654
• /
• 2007

Induction motors are widely used as a source of driving force in electric vehicles and pulse width modulation (PWM) inverters are applied to their operation. The issue is that insulation of inverter-fed induction motors (IFMs) are more stressed than in line-powered motors by transient voltages. This paper dealt with experimental results on transient voltage produced by the PWM operation of an induction motor. The peak and the dv/dt of transient voltage depending on the length of power feeding cable and operating frequency were investigated. In the experiment, transient voltages up to 3.3PU of the rated-inverter voltage were recorded for the cable length of 50m. As the cable length is increased, the peak voltage appeared at the motor terminals increases. This phenomenon can be explained by the reflection and the transmission of travelling wave. Consequently, special care for the cable length between the motor and the inverter should be taken in the use of IFM to ensure the full life of insulation system.

• Korean Journal of Materials Research
• /
• v.5 no.8
• /
• pp.936-944
• /
• 1995

The effects of Spinodal decomposition induced phase separated microstructure of InGaAsP/InP heterostructure on photoluminescence(PL) intensity and FWHM(full-width at half maximum) were investigated in this study. Lattice mismatches were measured by double crystal x-ray diffractometer, and the microstructures of phase separated InGaAsP were observed by transmission electron microscopy. It was found that the misfit stress calculated from lattice mismatch was related to the periodicity of Spinodal modulation. Strong dependence of PL intensity and FWHM on the modulation periodicity was also found. For systematic understanding of these observations, the interaction elastic strain energy function induced by misfit stress was proposed. The calculation illustrated that the microstructure of the epilayer such as Spinodal decomposition played an important role in determining the optoelectronic properties such as PL intensity and PL FWHM.

• Progress in Superconductivity and Cryogenics
• /
• v.14 no.3
• /
• pp.9-12
• /
• 2012

Usually, the AC loss from the superconducting element of an SFCL due to the load current is very small because it is composed of the combination of bifilar windings with very small reactance. Although the AC loss is small enough, we should be albe to predict for the design and control of the cryogenic system. In fact, an SFCL for the transmission voltage class may not generate ignorable AC loss because of the inevitable space between the HTS wires for the high voltage insulation and cryogenic efficiency. To measure the AC loss dependency on the space between the 2G HTS wires with the width of 4.4 mm, we prepared an experimental setup which could adjust the distance between the wires. We used two 500-mm length HTS wires in parallel and applied the current in the opposite direction for each wire to simulate a part of a current limiting module for a high voltage SFCL. We also put two couples of voltage taps at the ends of each wire and a cancel coil in the voltage measurement circuit to compensate the reactive component from the voltage taps. In this condition, we varied the distance between the wires to investigate the change of the transport current loss. A similar experimental study with HTS wire with the width of 12 mm is now in progress.

• Journal of Biosystems Engineering
• /
• v.43 no.4
• /
• pp.320-330
• /
• 2018

Purpose: The aim of this study was to investigate the harvesting performance of a prototype small combine for buckwheat and adlay. Methods: The prototype small combine was designed and constructed. Its ratio of grain loss, ratio of output components in the grain outlet, and field capacity for harvesting buckwheat and adlay were analyzed through field tests. Results: The prototype small combine required a working width of about 0.6 to 0.7 m to harvest buckwheat. The maximum travel speed was about 0.36 m/. The total ratio of grain loss was about 21.6%, which consisted of 8.8% at the header and 12.8% at the dust outlet. The grain and the material other than grain (MOG) ratios at the grain outlet were 94.1% and 5.9% respectively. In the case of adlay harvest, the maximum working width was about 1.2 m, that is, two rows. The range of maximum travel speed was about 0.45 to 0.46 m/s. When adlay was harvested in one row, the total ratio of grain loss ranged from 36.3 to 42.8% according to the cutting height. The cutting height of 30 cm resulted in a higher total ratio of grain loss than 60 cm and 90 cm. When the cutting height was 60 cm, there was no significant change in the total ratio of grain loss according to the number of working rows and the stage of the primary transmission shift. The total ratio of grain loss ranged from 35.2 to 37.7%. The grain and the MOG ratios at the grain outlet ranged from 93.1 to 95.8% and from 4.2 to 6.9%, respectively. No significant difference was observed in relation to cutting height, number of working rows, and the stage of the primary transmission shift. Conclusions: The prototype small combine for harvesting miscellaneous cereal crops showed good potential for the efficient harvesting of buckwheat and adlay. However, to improve the harvesting performance, there seems to be a need to develop new crop varieties suitable for machine-based harvesting and improve the transmissions, reels, separation/cleaning systems.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.2
• /
• pp.95-104
• /
• 2011

In this paper, the metamaterial transmission line (TL) based on the complementary spiral resonators (CSRs) and interdigital structure is presented for reducing the phase noise of the voltage-controlled oscillator (VCO). The metamaterial TL is realized by adopting the array of the CSRs etched on the ground plane and the interdigital transmission line on the signal plane. The interdigital TL on the signal plane has been used to obtain higher Q value than the conventional TL without the interdigital structure. The resonance properties and inherent saturation of Q value of the proposed metamaterial TL have been analyzed by varying the width of the TL on the signal plane, dimensions of the CSRs, current directions between the CSRs, number of the unit cell-pair of the CSRs, and whether or not there is the interdigital structure in this paper. The phase noise and tuning range of the proposed VCO are -127.50~-125.33 dBc/Hz at 100 kHz and 5.744~5.852 GHz.

• Korean Journal of Optics and Photonics
• /
• v.15 no.4
• /
• pp.287-292
• /
• 2004

This paper presents the effect of scratches on an optical connector interface surface on the insertion loss of optical connectors. We propose a model for calculating the insertion loss of optical connectors. The model is expressed in terms of geometrical parameters of scratches assuming that the transmission coefficient of a light wave on the scratch surfaces is linearly varied as a function of scratch depth. Geometrical parameters of scratches such as location, width, and depth of scratches are measured using 3D optical interferometry surface profiler. We obtain the equation of the transmission coefficient in terms of scratch depth comparing the experimental insertion loss data to the insertion loss data using the model presented in this paper. Using the model and the equation of the transmission coefficient presented in this paper, we present the results of the insertion loss of optical connectors for various geometrical parameters of scratches. Scratches which are located at longer than two times the core radius from the center of the core show negligible effect on the insertion loss of optical connectors.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.4
• /
• pp.791-799
• /
• 2008

An image recognition for surrounding conditions is very important in image transmission. In recently rears, as the information infrastructure is more general, the user-centered demands in which they want to identify by object's states image using wire or wireless environment have increased. However, existing mobile solution could be hard to expect high quality mage, because limitation of software processing according as network based on mobile terminal which has low band width supports software codec. To solve this weak point, this paper describes on hardware codec design based on MPEG-4 which is international video compression standard. Implemented system contains the embedded CPU for optimized design and it works high quality service as transmission speed and resolution in mobile circumstance.