• Nuclear Engineering and Technology
• /
• v.48 no.3
• /
• pp.795-798
• /
• 2016

Transmission X-ray tubes based on carbon nanotube have attracted significant attention recently. In most of these tubes, tungsten is used as the target material. In this article, the well-known simulator Geant4 was used to obtain some of the tungsten target parameters. The optimal thickness for maximum production of usable X-rays when the target is exposed to electron beams of different energies was obtained. The linear variation of optimal thickness of the target for different electron energies was also obtained. The data obtained in this study can be used to design X-ray tubes. A beryllium window was considered for the X-ray tube. The X-ray energy spectra at the moment of production and after passing through the target and window for different electron energies in the 30-110 keV range were also obtained. The results obtained show that with a specific thickness, the target material itself can act as filter, which enables generation of X-rays with a limited energy.

• Journal of KSNVE
• /
• v.9 no.2
• /
• pp.285-294
• /
• 1999

Transient analysis for compressible fluid flow has been performed experimentally and analytically to study the dynamic characteristics of the end volume transmission lines following a sudden pressure change a its entrance. The numerical method was developed based on the method of characteristics. The sudden pressure at its entrance was generated by rupture of diaphragm in a shock tube. The sudden pressure was used to obtain the response, as input signal for the numerical analysis. The response to the sudden pressure at the end volume was measured using a pressure transducer. The experimental result shows good agreements with the numerical result. The effects of tube length, its diameter and end volume magnitude are evaluated on the responses of the pressure and on the damping factor. It is found that the viscous damping effects on the response through the transmission pipeline becomes larger with increasing pi;eline length and decreasing diameter of the pipe and the fluid-elastic stiffness decreases with increasing the terminal volume. The numerical approach presented in this paper can be very useful in designing the instrument and control system.

• Journal of the korean Society of Automotive Engineers
• /
• v.13 no.3
• /
• pp.32-42
• /
• 1991

In SI engine research the pressure data in cylinder is the most important fundamental ones leading to engine efficiencies and performances. It is, therefore, necessary to obtain accurate pressure data and yet it is often impossible to install a reliable data producing, flush-mounted type pressure transducer in a cylinder of small and medium size multicylinder SI engines. When flush mounting the transducer is not possible, the spark-plug type pressure transducer is commonly used as an alternative. In this case, the transmission tube of spark-plug type pressure transducer introduces distortions in the pressure signal. Efforts were made to understand the dynamic characteristics of spark-plug pressure transducer by shock tube tests and real engine experiments. In engine experiment the cylinder pressure data were simultaneously obtained by both flush mounted and spark-plug type pressure transducers of certain transmission tube geometry. Those pressure data collected by spark-plug type pressure transducer were tested for correction to flush mounted ones by the application of transfer function. As a result of the calibration the IMEP difference between F/M data and improved S/P data was shown to be corrected about 75-98% from the original ones.

• The Journal of the Acoustical Society of Korea
• /
• v.34 no.3
• /
• pp.219-226
• /
• 2015

In this paper, derivation of the STL (Sound Transmission Loss) of a square plate installed in an impedance tube is discussed using an analytic method. Coupled motion of the plate vibration and acoustic field is considered. Vibration of the plate and pressure field inside the tube are expressed in terms of the infinite series of modal functions. Under the plane wave assumption, it is shown that consideration of the first few modes yields sufficiently accurate results. When the boundary of the plate is clamped, vibration mode is assumed as a multiplication of the beam modes corresponding to the crosswise directions. The natural frequencies of the clamped plate are calculated using the Rayleigh-Ritz method. It is found that the STL shows a dip at the lowest natural frequency of the plate, and increases as the frequency decreases below the natural frequency. Comparison of the result in this paper with the STL obtained by measurements and FE computations in the reference shows an excellent agreement.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.9
• /
• pp.964-970
• /
• 2014

In this study we have developed an anthropomorphic robot hand and arm by using tendon-tubes which can be used for people's everyday life as a robot's dynamic power transmission device. Most previous robot hands or arms had critical problem on dynamic optimization due to heavy weight of power transmission parts which placed on robot's finger area or arm area. In order to resolve this problem we designed light-weighted robot hand and arm by using tendon-tubes which were consisted of many articulations and links just like human's hand and arm. The most prominent property of this robot hand and arm is reduction of the weight of robot's power transmission part. Reduction of weight of robot's power transmission parts will allow us to develop energy saving and past moving robot hands and arms which can be used for artificial arms. As a first step for real development in this study we showed structural design and demonstration of simulation of possibility of a robot hand and arm by tendon-tube. In the future research we are planning to verify practicality of the robot hand and arm by applying sensing and controlling method to a specimen.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.5
• /
• pp.93-99
• /
• 2006

Flexible couplers are widely used for exhaust transmitted vibration reduction in vehicles. This paper describes an investigation into the acoustical characteristics of exhaust flexible coupler by the simulation and testing. Computational acoustic simulation is carrying out to investigate resonance frequency and transmission loss of decoupler using the boundary element method and transfer matrix approach. To confirm the acoustical simulation results of exhaust decoupler, we compare with measured experimental results by the test of transmission loss measurement system. In the comparison with simulation results and tests results, there is correctly fit the resonance frequency and the trend of transmission loss. Also, we show that the acoustical structure of decoupler is analogous to the expended tube or side branch resonator. The characteristics of exhaust decoupler have a marked increase in the acoustic attenuation at the specified frequency bend. Therefore the decoupler is applied to develop the exhaust system not only for the vibration isolator but also for the noise attenuator.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.567-572
• /
• 2001

A transmission of load that is transmitted by beam in steel beam-column joint depends on bond strength between concrete and steel tube. But it is different to transmit a load efficiently in the established concrete filled steel tubular column. Therefore, shear-connector is demanded for a reinforcement about a transmission of load. An ascent of bond stress and a transmission of load after debonding are expected by a reinforcement of shear-connector.

• Korean Journal of Optics and Photonics
• /
• v.7 no.1
• /
• pp.28-36
• /
• 1996

We have constructed and studied a laser system which consists of a multiplex spark gap with 8 couples of spark gaps and a multiple parallel plate capacitor type Blumlein transmission line circuit. In this laser system, the length of the laser tube, the length of the multiplex spark gap and the total thickness of the transmission line circuit are chosen to be 520 mm. The experimental results show that one couple of spark gaps cannot give a uniform and complete lasing through the whole laser tube. All the more, a multiplex spark gap could not perform completely and synchronously. However, a multiplex spark gap in found to contribute to the increase of laser output power and the laser has performed the best when the location is three quarters of the laser tube length.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.11 no.3
• /
• pp.33-38
• /
• 2002

This paper deals with pressure ripple attenuation far separated-type Hydrostatic Transmission (HST) consisting ova variable axial piston pump connected in an open loop to a fried displacement axial piston motor. Pressure ripples in HST is major source of vibration which can lead to fatigue failure of components and cause noise. In order to reduce the pressure ripple, an annular tube tripe hydraulic filter is proposed to attenuate pressure ripples with the high frequencies components to achieve better noise reduction in HST. The basic principle of a hydraulic filter is allied to propagation of pressure wave, reflection, absorption in cross section of discontinuity and resonance in the hydraulic pipeline. It is experimentally shown that the hydraulic filter attenuates about 30∼40dB of pressure ripple with high frequencies. These results will assist in modeling and design of noise reduction in hydraulic control systems, and provide a means of designing a quieter HST.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1994.06a
• /
• pp.704-709
• /
• 1994

The insertion loss is the measured change in power flux at a specified receiver, when the acoustic transmission path between it and the source is modified by the insertion of silencer element. Such measurements have clear and valid physical meaning particularly if the source impedance remains while the transmission path is altered. When the invarient condition is satisfied, the insertion loss is given by the ratio of the acoustic pressure in upstream to that in downstream of the silencer, and that of the particle velocity. The measurement is consisted of using an adaptation of the two microphone method to obtain the complex amplitude of the sound in upstream tube as well as in downstream tube of the silencer. Examples of the data, reduced and presented in terms of the pressure ratio and particle speed ratio, are compared with the theoretical calculations.