• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1996년도 International Conference on Agricultural Machinery Engineering Proceedings
• /
• pp.354-358
• /
• 1996

At design stage of the TRXI agricultural tractor transmission (New product of TongYang Moolsan Co., Ltd), the noise and vibration of the transmission were analyzed theoretically for the optimal design of the transmission . For this analysis, the finite element model was developed using a commercial computer software, ANSYS. The noise and vibration of the TRXI transmission housing were predicted by the modal analysis. Natural frequency of the TRXI transmission housing was ranged from 12.53Hz(1st mode ) to 30.05Hz(5th mode). The fifth mode took place at the bearing metal in the area of rear transmission housing and was very close to the gear mesh frequency (30.5Hz) of low rang gear at the low creep shifting . Based on the results , the bearing metal of the range shift housing was reenforced with the rib at design stage.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2005년도 춘계학술대회논문집
• /
• pp.307-310
• /
• 2005

Most of the electric power in the power system of South Korea is flowing from the south area to the north area, Seoul, in the capital of South Korea. Almost of the needs of the electric power in the capital area are about 43% of the total loads and generation plants are mainly located in the south area of South Korea. As mentioned the earlier characteristic, transmission congestion is one of the important research issues. Because of the limits of the power flows from the south to the north which are anticipated to be increased more and more in the future, these congestion situations may cause a serious voltage stability problem in emergency of the power system. Accordingly, we are interested in an interruptible load control program so as to solve this problem in emergency. This problem can be solved by an interruptible load management in emergency, however, the systematic and effective mechanism has not been presented yet. In this paper, the algorithm of interruptible load management plan using the line sensitivity to the loads for the transmission congestion management in emergency is presented. The proposed method is applied to 6-Bus sample system and their results are presented.

• ETRI Journal
• /
• 제44권4호
• /
• pp.543-559
• /
• 2022

To determine a suitable waveform for Internet of Things (IoT) transmission over low-Earth orbit (LEO) satellites, this paper reports the results of a performance comparison between chirp spread spectrum (CSS)-based LoRa and direct sequence spread spectrum (DSSS)-based Ingenu. The performance of both waveforms was measured in terms of the packet error rate, throughput, and packet loss rate, considering the Doppler effect caused by the high speed of LEO satellites and the interference among multiple terminals. Simulation results indicate that the DSSS scheme is more suitable than the CSS scheme for high-traffic IoT services because of its robustness against interference among multiple terminals. However, the CSS scheme is more suitable than the DSSS scheme for high-mobility IoT services because of its robustness against the Doppler effect. We discuss various solutions, such as the preprocessing of Doppler effect and avoidance of packet collision, to enhance the performance of the DSSS and CSS schemes. The simulation results of the proposed solution show that the enhanced DSSS scheme can be a proper waveform in IoT transmission over LEO satellites for both the high-traffic and high-mobility services.

• 한국정보처리학회:학술대회논문집
• /
• 한국정보처리학회 2004년도 춘계학술발표대회
• /
• pp.1453-1456
• /
• 2004

PARO, a power-aware routing optimization mechanism, is proposed in [1] to minimize the transmission power needed to forward packets between wireless devices in ad hoc network. The mechanism works by redirecting the route to pass through one or more intermediate nodes on behalf on source-destination pairs, then reducing the end-to-end transmission power. This paper will show an extension of this model and provide an analysis of the geometrical area lying between source and destination in which the intermediate node elects to perform redirection. The duration the intermediate node stays in that area is also computed.

• 한국초전도ㆍ저온공학회논문지
• /
• 제5권2호
• /
• pp.8-15
• /
• 2003

Nowadays, As power demand increases gradually, the call for underground transmission system increases. But it is very difficult and high in cost to construct new ducts and/or tunnels for power cables in metropolitan areas. HTS cable has the several useful characteristics such as increased power density, stronger magnetic fields and/or reduced losses. Therefore HTS cable can allow more power to be moved in existing ducts, which means very large economical and environmental benefits. In this paper, we investigate the status of korean power system and underground transmission system. Based on this, the feasibility study on applying HTS cable to korean power system is carried out and then we propose the new power system configuration of metropolitan area with HTS cable. Finally, we can get a conclusion that applying HTS cable to 154kV underground transmission line in metropolitan area such as seoul is very available. In addition, detail applicable cases are investigated; a)replace old conventional cable with HTS cable; b) apply HTS cable to constructing new underground transmission line; c)use HTS cable to resolve overload problem in conventional power system configuration.

• 한국가스학회지
• /
• 제22권5호
• /
• pp.24-30
• /
• 2018

극한지 장거리 천연가스 배관망의 경우 배관 특성 및 노선 조건에 따라 가스압력이 감소되기 때문에 가스 압력유지를 위한 승압 설비가 필요하다. 적절한 가스 압력 유지를 위해 승압기지 위치 간격을 근거리로 하여 압축비를 줄이거나 장거리로 하여 압축비를 증가시킬 경우 승압기지의 주요설비 가격, 건설 및 운전비용 등이 고려된 경제성 확보가 필요하다. 따라서 본 연구에서는 극한지 장거리 배관망 건설에 대한 선행 연구조사를 검토하고 극한지 지역에서 승압기지의 건설비용을 절감할 수 있는 주요설비를 구성하여 공정 개념설계를 수행하였다. 특히 러시아의 야쿠츠크~알단지역에 대한 가상 지역을 선정하였고, 이 가상지역은 총 배관길이 533km 이며, 승압기지 건설 위치를 달리한 시나리오를 제시하고 승압기지의 주요설비에 대한 용량을 산정하였다. 이 결과를 바탕으로 승압기지 건설비용을 최소화할 수 있는 경제성 평가 방안을 검토하였다.

• 한국자동차공학회논문집
• /
• 제14권5호
• /
• pp.107-114
• /
• 2006

This paper investigates the radiating source of electro-magnetic waves in the cabin of automobile with spark ignition engine. Front seats are very close to the engine room where electro-magnetic waves are expected to be radiating. But front seat area is believed to be a blind zone, which is not affected by radiating electro-magnetic waves, because a bulk board and floor board shield the front seat area. The level and frequency spectrum of electro-magnetic waves are measured at the passenger seat and the engine room. The measured frequency range is $145{\sim}365MHz$. As a results, the level of the electro-magnetic waves of automatic transmission vehicle is greater than -82dBm. The shapes of frequency spectrum of both engine room and passenger seat are look alike. But the level of electro-magnetic waves of manual transmission vehicle is less than -82dBm and the shapes of frequency spectrum of engine room and passenger seat are different to each other. From these results, we can say that any mal-function caused by electro-magnetic waves in the automobile cabin are only possible for automatic transmission vehicle. Also, it is believed that the radiating source of electro-magnetic waves is inside the vehicle. Thus, based on the transmission line theory, this paper presumably concludes that the cables which connect all the components inside a automatic transmission vehicle must be a radiating source of electro-magnetic waves in the cabin.

• International journal of advanced smart convergence
• /
• 제5권2호
• /
• pp.24-37
• /
• 2016

This paper proposes to increase the efficiency of energy in nodes, which rapidly drops during the transmission of the Low Energy Adaptive Clustering Hierarchy (LEACH), through the use of dual-hop layered application in the sensor field. Along with introducing the dual-hop method in the data transmission, the proposed single-hop method for short-range transmission and multi-hop transmission method between the cluster heads for remote transmission were also introduced. Additionally, by introducing a partial multi-hop method in the data transmission, a single-hop method for short range transmission method between the cluster heads for remote transmission was used. In the proposed DL-LEACH, the energy consumption of the cluster head for remote transmission reduced, as well as increased the energy efficiency of the sensor node by reducing the transmission distance and simplifying the transmission route for short-range transmission. As compared the general LEACH, it was adapted to a wider sensor field.

• 한국항공운항학회지
• /
• 제20권4호
• /
• pp.39-44
• /
• 2012

This paper propose a transmission method for "Transportation system" that can decide precise position under wide area road traffic environment. For precise position detecting, central station collect multiple receiver station's satellite navigation data and generate correction information. In this process, we need efficient real time transmission method for satellite navigation message that has variable data size. We propose real time data transmission method. This real time transmission method offer efficient processing structure for multiple receiver station's satellite navigation message. This paper explains proposed real time transmission method and proofs this transmission method.

• Wind and Structures
• /
• 제20권6호
• /
• pp.739-749
• /
• 2015

Field measurement of wind characteristics is of great significance for the wind engineering community. High-frequency anemometers such as ultrasonic anemometers are widely used to obtain the high-frequency fluctuating wind speed time history. However, conventional instrumentation systems may suffer from low efficiency, non-real time transmission and higher maintenance cost, and thus are not very appropriate in the field measurement of strong winds in remote areas such as mountain valleys. In order to improve the field measurement performance in those remote areas, a wireless high-frequency anemometer instrumentation system for field measurement has been developed. In this paper, the architecture of the proposed instrumentation system, and measured data transmission and treatment will be presented firstly. Then a comparison among existing instrumentation systems and the proposed one is made. It shows that the newly-developed system has considerable advantages. Furthermore, the application of this system to the bridge site located in the mountain valley is discussed. Finally, typical samples of measured data from this area are presented. It can be expected that the proposed system has a great application potential in the wind field measurement for remote areas such as the mountainous or island or coastal area, and hazardous structures such as ultra-voltage transmission tower, due to its real-time transmission, low cost and no manual collection of data and convenience.