• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.229.2-229.2
• /
• 2014

Graphene, an allotrope of carbon, is a two-dimensional material having a unique electro-mechanical property that shows significant change of the electrical conductance under the applied strain. In addition of the extraordinary mechanical strength [1], graphene becomes a prospective candidate for pressure sensor technology [2]. However, very few investigations have been carried out to demonstrate characteristics of graphene sensor as a device form. In this study, we demonstrate a pressure sensor using graphene double layer as an active channel to generate electrical signal as the response of the applied vertical pressure. For formation of the active channel in the pressure sensor, two single graphene layers which are grown on Cu foil (25 um thickness) by the plasma enhanced chemical vapor deposition (PECVD) are sequentially transformed to the poly-di-methyl-siloxane (PDMS) substrate. Dry and wet transfer methods are individually employed for formation of the double layer graphene. This sensor geometry results a switching characteristic which shows ~900% conductivity change in response to the application of pulsed pressure of 5 kPa whose on and off duration is 3 sec. Additionally, the functional reliability of the sensor confirms consistent behavior with a 200-cycle test.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.276-276
• /
• 2014

High-performance, fully-transparent, and top-gated oxide thin-film transistor (TFT) was successfully fabricated with Ta2O5 high-k gate dielectric on a glass substrate. Through a self-passivation with the gate dielectric and top electrode, the top-gated oxide TFT was not affected from H2O and O2 causing the electrical instability. Heat-treated InSnO (ITO) was used as the top and source/drain electrode with a low resistance and a transparent property in visible region. A InGaZnO (IGZO) thin-film was used as a active channel with a broad optical bandgap of 3.72 eV and transparent property. In addition, using a X-ray diffraction, amorphous phase of IGZO thin-film was observed until it was heat-treated at 500 oC. The fabricated device was demonstrated that an applied electric field efficiently controlled electron transfer in the IGZO active channel using the Ta2O5 gate dielectric. With the transparent ITO electrodes and IGZO active channel, the fabricated oxide TFT on a glass substrate showed optical transparency and high carrier mobility. These results expected that the top-gated oxide TFT with the high-k gate dielectric accelerates the realization of presence of fully-transparent electronics.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.3
• /
• pp.561-566
• /
• 2013

In this paper, android phone information push system based on the XMPP protocol is proposed. For this, we implement a XMPP(eXtensible Message and Presence Protocol) based instant message system in C/S network environment by using Java language and eclipse device. This system not only allows sending and receiving messages from the PC server to mobile phone client, but also enables the expansion into the smack package of an android phone. Thus, this system shown, in this paper has the better performance in transmission and transfer speed than those of the basic XMPP protocol system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.191-194
• /
• 2003

Through using aspheric lens can result in advantages such as an improved optical transfer function, a reduced distortion path or the realization of special image field curvatures. Using the diamond turning method for generating aspherics, the company claim to be able to generate surfaces with a form error of less than $0.33\;{\mu}\;m$ and a surface roughness of less than $0.025\;{\mu}\;m$. In this paper, we are manufacturing thermal image aspheric lens. Thermal image system is electro-optical imaging device which can make visible the difference of infrared energy naturally emitted by objected. In the result of aspherical surface, the form accuracy of about $0.24\;{\mu}\;m$ P-V was obtained and the surface roughness Ra $0.004\;{\mu}\;m$. Also, a brief review of Ultra-precision system Korea photonics technology institute(KOPTI) is present in this paper.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.287-287
• /
• 2010

We report a new direct patterning method, called liquid bridge-mediated nanotransfer molding (LB-nTM), for the formation of two- or three-dimensional structures with feature sizes between tens of nanometers and tens of micron over large areas. LB-nTM is based on the direct transfer of various materials from a mold to a substrate via a liquid bridge between them. This procedure can be adopted for automated direct printing machines that generate patterns of functional materials with a wide range of feature sizes on diverse substrates. Arrays of TIPS-PEN TFTs were fabricated on 4" polyethersulfone (PES) substrates by LB-nTM using PDMS molds. An inverted staggered structure was employed in the TFT device fabrication. A 150 nm-thick indium-tin oxide (ITO) gate electrode and a 200 nm-thick SiO2dielectric layer were formed on a PES substrate by sputter deposition. An array of TIPS-PEN patterns (thickness: 60 nm) as active channel layers was fabricated on the substrate by LB-nTM. The nominal channel length of the TIPS-PEN TFT was 10 mm, while the channel width was 135 mm. Finally, the source and drain electrodes of 200 nm-thick Ag were defined on the substrate by LB-nTM. The TIPS-PEN TFTs can endure strenuous bending and are also transparent in the visible range, and therefore potentially useful for flexible and invisible electronics.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.12
• /
• pp.85-93
• /
• 2009

This research is intended to grasp the characteristics of heat flow inside auxiliary power device engine room to obtain the design basic data through numerical analysis and experiment. For experiment cost reduction, numerical analysis was done to obtain quantitative data by observing the change in temperature distribution of major parts according to changes in normal condition, incompressible condition, engine surface heat emission rate and absorption temperature with the use of commercial STAR-CD. The experiment was done by grasping the temperature distribution of major interested parts inside engine room in loaded and unloaded conditions during engine operation. The temperature distribution data here will serve as useful design data during APU engine room designing.

• Journal of Animal Science and Technology
• /
• v.62 no.2
• /
• pp.276-291
• /
• 2020

This study was conducted to investigate behavioral changes in laying hens (Hy-Line Brown) after transfer to a multi-tier system from the floor system and to examine their production performance. The hens were randomly divided into two groups and were allocated to the multi-tier system and the floor system at a commercial farm. Behavior of the laying hens was recorded by CCD (charge-coupled device) cameras and a digital video recorder. The data were scanned every 2 min to obtain an instantaneous behavioral sample or were immediately counted whenever the hens exhibited a designated behavior. Behavior changed dramatically during the first seven days. Egg production was higher in the multi-tier system, while cracked and dirty eggs were more frequent in the floor system (p < 0.05). No differences in mortality rate or egg quality were observed between the groups. In conclusion, the hens needed at least seven days to adapt to the multi-tier system. The multi-tier system was more efficient than the floor system in terms of production performance.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.2
• /
• pp.85-88
• /
• 2010

Deep blue organic light emitting diodes (OLEDs) were fabricated using 5 wt.% doped BCzVBi with various blue host materials such as NPB, DPVBi, MADN and TPBi. A blue OLED device, using DPVBi as host material, was constructed via NPB ($500\;{\AA}$) / DPVBi:BCzVBi ($200\;{\AA}$) / Bphen ($300\;{\AA}$) / LiF ($20\;{\AA}$) / Al ($1,000\;{\AA}$) and it shows a maximum luminescence of $4,838\;cd/m^2$, a current density of $32.7\;mA/cm^2$, a luminous efficiency of 3.3 cd/A and CIExy coordinates of (0.19, 0.15) at 4.5 V whereas the luminous efficiencies and CIExy coordinates of other blue OLEDs using NPB, MADN and TPBi as host materials have 1.1, 2.6 and 2.0 cd/A and (0.15, 0.11), (0.15, 0.10) and (0.15, 0.10), respectively. Energy transfer mechanisms between BCzVBi and its host materials were discussed with an energy band structure of host materials.

• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.2
• /
• pp.18-29
• /
• 1992

As more application programs have graphic functions, standards in the computer graphics are becoming important. To develop a computer aided design and production system for ships, which would be used by different shipyards, a graphic library should be chosen as a standard. Existing ISO graphic standards and de facto industrial standards are surveyed. They are, to name some of them, GKS, PHIGS, X-Window, PEX, PDES, and STEP. GKS and PHIGS concern about the application programmer's interface. Others handle the device interface. PDES and STEP are to standardize the graphical data transfer between heterogeneous systems. Their inter-relations are investigated. Some preliminary suggestions for the choice of graphic standards are included in this paper.

• Journal of the Korean Solar Energy Society
• /
• v.22 no.2
• /
• pp.39-47
• /
• 2002

The thermosyphon SDHWS and the loop type thermosyphon systems are widely used for domestic hot water system. The loop type thermosyphon is a circulation device for transferring the heat produced at the evaporator to the condenser area in the loop. In this study, the operating characteristics of various working fluids being used have been identified. The working fluids employed in the study were ethanol. water, and a binary mixture of ethanol and water. The volume of working fluid used in this study were 30%, 40%, 50%, 60% and 70% of evaporator volume. It is observed that, in the thermosyphon with low volume of working fluid, such as 30% or 40%, the fluid was dried out. The flow pattern and mechanism of the heat transfer were identified through this study. Flow patterns of the binary mixture working fluid were also investigated, and the patterns were recorded in the camera. The system parameters were calculated using the thermal performance data. Modelling of the system was carried out using PSTAR method and TRNSYS program.