• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.875-880
• /
• 2002

It is necessary to determine the vibration source and its transmission paths in order to develop a low-noise compressor. Through the use of multiple-input/single-output(MISO) mode1, the transmission paths of vibration within a reciprocating compressor have been investigated. In order to identify the transmission path, we measure the accelerations of the block and transverse vibrations of the line discharge tube. As outputs, vibrations of compressor shell were measured at three positions; cylinder head, one near the suction line, and the top of upper shell. The partial coherence function and transfer function are obtained ken the measured data, and the results are observed in order to determine vibration source and its influence on the shell vibration.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.6
• /
• pp.736-744
• /
• 2016

Network on chip (NoC) is an emerging technology in the field of multi core interconnection architecture. The routers plays an essential components of Network on chip and responsible for packet delivery by selecting shortest path between source and destination. State-of-the-art NoC designs used routing table to find the shortest path and supports four ports for packet transfer, which consume high power consumption and degrades the system performance. In this paper, the multi port multi core router architecture is proposed to reduce the power consumption and increasing the throughput of the system. The shared buffer is employed between the multi ports of the router architecture. The performance of the proposed router is analyzed in terms of power and current consumption with conventional methods. The proposed system uses Modelsim software for simulation purposes and Xilinx Project Navigator for synthesis purposes. The proposed architecture consumes 31 mW on CPLD XC2C64A processor.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.22-24
• /
• 2008

This paper presents a numerical model of internal flows in a lubricant supplying and scavenging flow path of an aero-engine lubrication system. The numerical model was built in the General Analysis Software of Aero-engine Lubrication System, GASLS, developed by Northwestern Polytechnical University. The lubricant flow flux, pressure and temperature distribution at steady state were calculated. GASLS is a general purpose computer program employed a 1-D steady state network algorithm for analyzing flowrates, pressures and temperatures in a complex flow network. All kinds of aero-engine lubrication systems can be divided into finite correlative typical elements and nodes from which the calculation network be developed in GASLS. Special emphasis is on how to use combined elements which is a type of typical elements to replace some complex components like bearing bores, accessory gearboxes or heat exchangers. This method can reduce network complexity and improve calculation efficiency. Final computational results show good agreement with experimental data.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.5
• /
• pp.66-71
• /
• 2012

The capacity criteria have been proposed in order to select a cooperative relay node in WSNs, under the environment where direct path has a poor link gain. This process may ensure the efficiency improvement of signal transfer between source and destination and reduction of energy consumption as well. Two criteria are incorporated to select a cooperative relay node. Firstly, calculate the energy gain ratio between the relay path and the direct path. These are defined as the ratio between the energy factors of 1/g and 1/B. Each stands for an inverse of direct path gain and relay path gain. Secondly, investigate the effects of relay node's usage in WSNs through the simulation in terms of energy consumption. In conclusion, using a selected cooperative relay node based on the selected criteria is effective in terms of both energy efficiency and capacity of WSNs especially when direct path gain is relatively low.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.10a
• /
• pp.591-592
• /
• 2009

• Journal of KSNVE
• /
• v.1 no.2
• /
• pp.141-147
• /
• 1991

A vectorial approach is used to reduce the objectionable booming noise in the vehicle interior cabin. After identifying the structural transmisson paths, the structural-acoustic transfer functions are evaluated at those mounting positions. Using the measured deformations in the mounting elements and multiplying them with each dynamic stiffness value one can easily get the dynamic input forces acting on the mounting elements. By summing all the contributors vectorially, most important contributor or transmission path can be determined. According to the experimental information, devised countermeasures are applied to a development car and good results are obtained.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.04a
• /
• pp.623-624
• /
• 2009

• Proceedings of the IEEK Conference
• /
• 2001.06a
• /
• pp.77-80
• /
• 2001

In this paper, it is analyzed the statistical characteristics on the transmission performance of the optical SCM transmission in the CDMA RF signal relay system. Using Mach-Zehnder modulator, optical signal is regenerated into CDMA RF signal. Transfer function model of mach-Zehnder modulator is approximated to the third power of the input signal using Taylor series. BER results are analyzed under the multiple access interference and multi-path fading environment.

• Journal of Digital Convergence
• /
• v.14 no.1
• /
• pp.453-463
• /
• 2016

This study examined the relationship among dropout, organizational trust, and intention to transfer in the department affiliated with Physical Education. Data were collected from 480 students in the department affiliated with Physical Education from 6 institutions of a 4-year university located in Seoul, Gyeonggi-do, Incheon, and ChungChong-do. For the research model analysis, a structural equation model and bootstrapping were conducted. Results indicated that the academic domain, the social domain, and the environmental domain of dropout had a positive effect on organizational trust. But the only the academic domain in the relationship between dropout and intention to transfer affected intention to transfer positively. The social domain and the environmental domain were not statistically significant on intention to transfer. Moreover, organizational trust had a positive effect on intention to transfer. Finally, organizational trust partially mediated the path between the academic domain and intention to transfer. It fully mediated the paths between the social domain and the environmental domain and intention to transfer.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.17 no.6
• /
• pp.14-24
• /
• 2018

Pedestrian movement of passengers using smart card within stations can be divided into three types of activities - straight ride and alight, line transfer, and station transfer. Straight ride and alight is transfer activity for which the card terminal and embarking line are identical. In this case, straight ride occurs at the origin station and straight alight occurs at the destination station. Line transfer refers to activity in which the subway line embarked on by the passenger is different from that which is disembarked. Succinctly, line transfer is transfer at a middle station, rather than at origin or destination stations. Station transfer occurs when the card terminal line and embarking line are different. It appears when station transfer happens at the origin station as starting transfer, and at the destination station as destination transfer. In the case of Metropolitan smart card data, origin and destination station card terminal line number data is recorded, but subway line data does not exist. Consequently, transportation card data, as it exists, cannot adequately be used to analyze pedestrian movement as a whole in subway stations. This research uses the smart card data, with its constraints, to propose an analysis model for passenger pedestrian movement within subway stations. To achieve this, a path selection model is constructed, which links origin and destination stations, and then applied for analysis. Finally, a case study of the metropolitan subway is undertaken and pedestrian volume analyzed.