• International Journal of Control, Automation, and Systems
• /
• v.6 no.2
• /
• pp.234-242
• /
• 2008

The purpose of this paper is to verify the practical effectiveness of an interphalangeal coordination-based joint motion planning method for humanoid finger operations. For the purpose, several experiments have been performed and comparative experimental results are shown. Through the experimental works, it is confirmed that according to the employed joint motion planning method, the joint configurations for a finger's trajectory can be planned stably or not, and consequently the actual joint torque command for controlling the finger can be made moderately or not. Finally, this paper analyzes that the interphalangeal coordination-based joint motion planning method is practically useful for implementing a stable finger manipulation. It is remarkably noted that the torque pattern by the method is well-balanced. Therefore, it is expected that the control performance of humanoid or prosthetic fingers can be enhanced by the method.

• Journal of Astronomy and Space Sciences
• /
• v.20 no.4
• /
• pp.365-374
• /
• 2003

Satellite formation flying is currently an active area of research in the aerospace engineering. So it has been researched by various authors. In this study, a tracking controller using sliding mode techniques was designed to control a satellite for the satellite formation flying. In general, Hill's equations are used to describe the relative motion of the follower satellite with respect to the leader satellite. However the modified Hill's equations considering the $J_2$ perturbation were used for the design of sliding mode controller. The extended Kalman filter was applied to estimate the state vector based on the measurements of relative distance and velocity between two satellites. The simulation results show that the follower satellite tracks the desired trajectory well by thruster operations based on the sliding mode control law.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.1
• /
• pp.48-55
• /
• 2011

Hydraulic excavator is one of the most widely used heavy machines in construction sites including dismantling. In the dismantling sites, the excavators equipped with crusher or breaker carry out dangerous operations, so drivers are always exposed to unexpected danger. For safety operation, remote control of the hydraulic excavator has been studied using proportional control valve, which requires an appropriate motion control of its bucket tip. In this case, kinematics and dynamics analysis have to be preceded through modeling of excavator. However, it is difficult to acquire reasonable results from the analysis due to insufficient information of physical parameters such as mass of each links and locations of mass centers, etc. This study deals with the trajectory control of bucket tip, which is based on experimental estimation of cylinder output force. The estimated forces are fed into the control of each cylinder in order to compensate gravitational and frictional effects in the cylinders. The control was applied to horizontal trajectories that are for flattening work.

• School Mathematics
• /
• v.7 no.4
• /
• pp.403-425
• /
• 2005

The study aims to get real picture of primary mathematics education based on RME in the Netherlands focusing on number and operations strand by reflecting and analyzing the documents in relation to the primary school mathematics curriculum. In order to attain these purposes, the present paper describes the core goals for mathematics education, Dutch Pluspunt textbook series for the primary school, and a learning-teaching trajectory by TAL project which are determinants of the Dutch primary school mathematics curriculum. Under these reflections on the documents, it is analyzed what is the characteristics of number and operations strand in the Nether-lands as follows: counting numbers, contextualization, positioning, structuring, progressive algoritmization based on levels, estimation and insightful use of a calculator. Finally, discussing Points for improving our primary mathematics curriculum and textbook series development are described.

• The Journal of Korea Robotics Society
• /
• v.10 no.3
• /
• pp.139-145
• /
• 2015

This paper proposed a method of cooperative control of three mobile robots for carrying an object placed on a floor together. Each robot moves to the object independently from its location to a pre-designated location for grasping the object stably. After grasping the common object, the coordination among the robots has been achieved by a master-slave mode. That is, a trajectory planning has been done for the master robot and the distances form the master robot to the two slave robots have been kept constant during the carrying operation. The localization for mobile robots has been implemented using the encoder data and inverse kinematics since the whole system does not have the slippage as much as a single mobile robot. Before the carrying operation, the lifting operations are implemented using the manipulators attached on the top of the mobile robots cooperatively. The real cooperative lifting and carrying operations are implanted to show the feasibility of the master-slave mode control based on the kinematics using the mobile manipulators developed for this research.

• International Journal of Control, Automation, and Systems
• /
• v.4 no.2
• /
• pp.217-226
• /
• 2006

Grasping and manipulation by hands can be considered as one of inevitable functions to achieve the performances desired in humanoid operations. When a humanoid robot manipulates an object by his hands, each finger should be well-controlled to accomplish a precise manipulation of the object grasped. So, the trajectory of each joint required for a precise finger motion is fundamentally necessary to be planned stably. In this sense, this paper proposes an effective joint motion planning method for humanoid fingers. The proposed method newly employs a bio-mimetic concept for joint motion planning. A suitable model that describes an interphalangeal coordination in a human finger is suggested and incorporated into the proposed joint motion planning method. The feature of the proposed method is illustrated by simulation results. As a result, the proposed method is useful for a facilitative finger motion. It can be applied to improve the control performance of humanoid fingers or prosthetic fingers.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.1
• /
• pp.11-18
• /
• 2011

A worm screw is widely used in a geared motor unit for motion conversion from rotation to linear. For mass production of a high quality worm, the current rolling process is substituted with the milling process. Since the milling process enables the integration of all operations of worm manufacturing on a CNC(Computer Numerical Control) lathe, productivity can be remarkably improved. In this study, the tooling system for side milling on a CNC lathe to improve machinability is developed. However, the cutting tool-workpiece interference is important factors to be considered for producing high quality worms. For adaptability of various worms machining, the tool-workpiece interference simulation system based on a tool-tip trajectory model is developed. The developed simulation system is verified through several kinds of worms and experimental results.

• Korean Management Science Review
• /
• v.9 no.1
• /
• pp.3-15
• /
• 1992

In this paper, we study a manufacturing system of serial stages with general service times, in which the production of each stage and the coordination of stages are controlled by Kanban discipline. This Kanban discipline is modeled as a Discrete Event Dynamic System and a system of recursive equations is applied to study the dynamics of the system. The recursive relationship enables us to compare this Kanban discipline with the other blocking disciplines such as transfer blocking, service blocking, block-and-hold b, and block-and-hold K, and the Kanban is shown to be superior to the other disciplines in terms of makespan and throughput. As a special case, two stages Kanban system is modeled as $C_2/C_2/1/N$ queueing system, and a recursive algorithm is developed to calculate the system performance. In optimizing the system performance, the stochastic optimization approach of Robbins-Monro is employed via perturbation analysis, the way to estimate the stochastic partial derivative based on only one sample trajectory of the system, and the required commuting condition is verified. Then the stochastic convexity result is established to provide second-order optimality condition for this parametric optimization problem.

• Proceedings of the KSRS Conference
• /
• 2004.10a
• /
• pp.367-370
• /
• 2004

We model a moving object as a sizable physical entity equipped with GPS, wireless communication capability, and a computer such as a PDA and mobile phone. Furthermore, we have observed that a real trajectory of a moving object is the result of interactions among moving objects in the system yielding Multi-points instead of a line segment. In this paper, the new types and operations are integrated seamlessly into the moving object framework to achieve a relatively simple, consistent and powerful overall model and query language for constrained and unconstrained movement.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.12
• /
• pp.47-54
• /
• 2009

A worm screw is widely used in a geared motor unit for motion conversion from rotation to linear. For mass production of a high quality worm, the current rolling process is substituted with the milling process. Since the milling process enables the integration of all operations of worm manufacturing on a CNC(Computer Numerical Control) lathe, productivity can be remarkably improved. In this study, the tooling system for planetary milling on a CNC lathe to improve machinability is developed. However, the cutting tool-workpiece interference is important factors to be considered for producing high quality worms. For adaptability of various worms machining, the tool-workpiece interference simulation system based on a tool-tip trajectory model is developed. The developed simulation system is verified through several kinds of worms and experimental results.