• 한국항만학회지
• /
• 제13권1호
• /
• pp.87-100
• /
• 1999

This study was focused on analyzing the headway of various types of trailer in Pusan city with the high heavy vehicle rate. Then Passenger Car Equivalent(PCE) was calibrated in order to identify the impact of trailers in the traffic flow at the signalized intersections. To fulfill this goal types of trailer were classified into five categories such as full trailer semi-trailer unloaded semi-trailer semi-trailer loaded with 20ft container and semi-trailer loaded with 40ft container and Passenger Car Equivalents were identified. the Results are as follows: 1) The PCE’s were 2.64, 1.51, 2.09, 2.16 and 2.23 respectively. 2) The saturation flow rate on the signalized intersection was lower than that on the multi-lane highway in the big city of Korea. 3) The start-up delay on the thru lane was similar to the average value in our country but the start-up delay on the left-turn lane was longer than the average value in our country by the impact of container Vehicles.

• Journal of Biosystems Engineering
• /
• 제33권4호
• /
• pp.224-229
• /
• 2008

This study was aimed to minimize the impact force and vibration transmitted to the transporting materials from the trailer and wheel shaft by installing the leaf spring suspension device at the space between the wheel shaft and frame of power tiller trailer. The developed trailer equipped with leaf spring suspension device was compared to the existing trailer without suspension device, in order to identify the vibration absorption effect of the leaf spring. The results of this study could be summarized as follows; (1) The length and the maximum bending amount of the leaf spring were designed as 1,000 mm and 42 mm, respectively, considering the possible space for installing at below the trailer. When 4 leaf springs were installed on both wheel shafts, the allowable maximum load was identified as 9,418 N. (2) The average vibration accelerations for the frequency less than 20 Hz, where the severe transporting loss could be represented, were $0.017\;m/s^2$ and $0.133\;m/s^2$ for the developed and the existing trailer, respectively, showing the vibration absorption effect of about 87%. And the average vibration accelerations on the driver's seat for the frequency less than 20 Hz were $0.01\;m/s^2$ and $0.20\;m/s^2$ for the developed and the existing trailer, respectively, which showed the similar vibration absorption effect. (3) The change of the average vibration accelerations for the frequency from 20 Hz to 80 Hz showed the similar tendency with the result for the frequency less than 20 Hz, but the effect for developed trailer was reduced slightly. And the effect of vibration absorption for the above 80 Hz was reduced highly. However, by installing the leaf spring suspension device at the trailer, the low frequency below 40 Hz, which could affect on transporting loss severely, could be reduced highly. (4) The maximum vibration acceleration for the frequency less than 20 Hz were $0.027\;m/s^2$ and $1.267\;m/s^2$ for the developed and the existing trailer, respectively. And the change of maximum acceleration between 20 Hz and 120 Hz was showed similar tendency with the result for the frequency less than 20 Hz, but the width of change was reduced highly.

• 한국도로학회논문집
• /
• 제8권3호
• /
• pp.89-103
• /
• 2006

본 연구에서는 도로 소음 측정시 다양한 형태로 존재하는 환경소음의 영향을 최소화하고 시간과 장소의 구애 없이 공용 중인 도로 상에서도 측정 및 평가를 가능토록 하기 위해 타이어/포장 소음 측정용 Trailer 장비를 제작 개발하였다. 기존 문헌조사를 바탕으로 도로소음의 특성을 파악하고 국외의 다양한 CPX Trailer 관련 연구사례를 살펴보았으며, 장비의 설계 및 제작 원리를 정립하였다. 이를 바탕으로 HEART CPX Trailer 관련 연구사례를 살펴보았으며, 반무향실 제작에 관한 적합성, 장비의 측정 정밀도 및 현장 적용성 등의 검증을 위해 다양한 시험을 수행하였다. HEART CPX Trailer 장비의 반무향실 제작에 대한 적합성 시험에서는 각 주파수 대역별에 따른 적합성 및 신뢰도를 확인할 수 있었으며, 도로 소음특성 평가용 장비로서 적합하다고 판단된다. 반복측정 시험에서는 각 속도별 및 마이크론폰의 위치별로 우수한 측정 정밀도를 확인할 수 있었다. 공용 중인 상태에서 수행한 도로소음 측정 결과는 2003년 중앙대학교에서 교통 개방 전에 동일구간에 대해 수행하였던 CPB 측정 결과와 유사한 경향을 보였다. 이는 견인차량의 기계소음을 비롯한 공용 중인 도로 주변의 환경소음으로부터 영향을 거의 받지 않기 때문이라 판단되며, 본 장비를 활용한다면 공용 중에도 객관적인 소음 측정이 가능함을 확인할 수 있었다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2000년도 추계학술대회 논문집
• /
• pp.491-498
• /
• 2000

This study was carried out about the design and FEM analysis of articulated Trailer car with aluminum bodyshell for Korean High Speed Train of maximum operating speed of 350㎞/h. The integral design by extra-long extruded sections made possible through the use of aluminium alloys and continuous window shape with skin were adopted in the design of aluminium bodyshell. Articulated structures in each trailer's end were bolted laterally on end structure. FEM analysis showed that the design satisfied the specified load criteria. This study describes process and result of development of aluminum trailer bodyshell for KHST.

• Journal of Biosystems Engineering
• /
• 제12권3호
• /
• pp.17-29
• /
• 1987

A 10-degree of freedom mathematical model of motion for power tiller-trailer system was developed. This model can predict motion characteristics of power tiller trailer system while travelling over smooth and irregular ground surfaces under various operating conditions. The model provide, the fundamental data needed to improve the stability of power tiller-trailer systems.

• 생물환경조절학회지
• /
• 제21권4호
• /
• pp.437-444
• /
• 2012

본 연구에서는 현제 농가에서 사용하고 있는 진동흡수장치가 전혀 없는 트레일러(E)와 트레일러의 적재규격에 적합하게 평판스프링과 쇽업쇼바를 동시에 설계 제작한 트레일러(I)를 사용하였다. 트레일러에 360kg의 배를 4층으로 적재한 상태로 아스팔트 도로 위를 2m/s로 정속 주행하면서 발생된 평균 진동 주파수의 크기를 상호 비교하여 개발된 트레일러의 진동흡수 효과를 비교 분석하였다. 개발한 현가장치를 장착한 개량된 트레일러는 60Hz 이하와 80Hz 이하의 주파수에서 기존 트레일러에 비해 진동 가속도의 감소 효과가 매우 크게 나타났다. 기존 트레일러에 비하여 개량된 트레일러에서 평균 진동가속도의 크기는 주파수 영역에 따라서 다르긴 하지만 3분의 1까지 대폭 감소시킬 수 있었다. 후방의 상층에 적재된 농산물일수록 진동가속도의 크기가 높아 부패가 빨리 진행 된다고 보고된 논문과 일치하지 않는 이유는 전 연구자는 적재함의 길이가 14,000mm이었고 본 시험에서 사용한 적재함은 1,820mm로 비교적 짧은 것에서 얻어진 결과로 일정한 경향을 찾기가 어려웠던 것으로 판단된다. 모든 주파수의 영역에서 개량된 트레일러가 기존의 트레일러에 비하여는 진동가속도의 크기가 현저히 낮게 나타났다. 특히 40Hz에서 80Hz까지의 주파수대에서 3분의 1로 진동가속도의 크기를 줄일 수 있어서 농산물의 수송 손실을 대폭 감소시킬 수 있을 것으로 판단된다.

• 한국항해항만학회지
• /
• 제32권8호
• /
• pp.629-636
• /
• 2008

현재 기존 철송 시스템에 있어서 문제점인 출발지와 목적지 사이 발생하는 복잡한 작업 프로세스(job process)를 간소화하여 철송 운임비감소와 물류운송의 체계 개선 및 활성화에 기여할 수 있는 시스템으로 DMT(Dual Mode Trailer) 시스템을 들 수 있다. 이에 본 기술의 국내적용 및 개발을 위해 기술동향 조사 및 국내 적용시 고려사항, 국내 적용 접합 모델 도출 등 기술성을 분석하였다.

• Journal of Biosystems Engineering
• /
• 제28권1호
• /
• pp.1-10
• /
• 2003

A computer simulation was carried out to determinate the optimum capacity of bulk type trailer which is used as a tractor attachment. Soil physical properties. such as soil moisture content. bulk density, soil hardness and soil texture were measured in the 10 major rice production area for computer simulation. Mathematical model which include soil physical properties and vehicle factor was used for computer simulation. Most of the soil texture of the investigated area was silty loam. Soil moisture content ranged between 30 and 40% mostly. Soil bulk density was in the range of 1.500 to 1.700 kg/㎥. Soil hardness ranged between 1 to 18 kg/$\textrm{cm}^2$. Soil hardness incorporate the effects of many soil physical properties such as moisture content texture and bulk density, and so the range of soil hardness was greater than any other physical properties. The capacity of bulk type trailer was above 3000 kg$_{f}$ fer the most of the investigated area. and mostly in the range of 4000 to 6000 kg$_{f}$ depending upon the slip. But for the soft soil area such as Andong and Namyang. tractor itself had mobility problem and showed minus trailer capacity for some places. For this area. the capacity of bulk type trailer ranged between 1000 and 2000 kg$_{f}$ mostly so bulk type trailer should be designed as a small capacity compared to the other area.ared to the other area. area.

• Journal of Advanced Marine Engineering and Technology
• /
• 제25권1호
• /
• pp.124-130
• /
• 2001

This paper presents a methodology on automation of a trailer type vehicle which consists of two parts: a tractor and a trailer. Backward moving and parking control is very important to automate this type of vehicle. It is difficult to control the motion such a trailer vehicle whose dynamics in non-holonomic. Therefore, in this paper, the modeling and parameter estimation of the system using a RCGA(real-coded genetic algorithm) is proposed and a backward path tracking control algorithm is then obtained. The simulation results verify the effectiveness of the proposed method.

• Journal of Biosystems Engineering
• /
• 제23권6호
• /
• pp.549-560
• /
• 1998

The dynamic model of a tractor-trailer system developed in the first part of this paper was verified in this article by comparing the simulated acceleration responses of the system with actually measured ones. A commercially available tractor and a trailer were used for the verification test. Values of the model parameters were measured or theoretically derived if the measurement was practically impossible. The tractor-trailer system was operated with different forward speeds over three equally spaced half-sine bumps on the flat concrete surface. Results of the verification tests showed that autospectra of the measured and simulated accelerations of the tractor-trailer system agreed well up to the frequencies slightly feater than the fundamental frequencies of the ground excitations and at the frequencies of engine excitations. The mean of normalized errors of the simulated responses to the measured ones was estimated to be less than 10% for all the test runs. The peak responses in the autospectra also coincided well both in the frequency and magnitude.