• International Journal of Automotive Technology
• /
• 제1권1호
• /
• pp.48-55
• /
• 2000

Two major roles of the traction control system (TCS) are to guarantee the acceleration performance and directional stability even in extreme road conditions, under which average drivers may not control the car properly. Commercial TCSs use experiential methods such as lookup table and gain-scheduling to achieve proper performance under various road and vehicle conditions. This paper proposes a new slip controller which uses the brake and the throttle actuator simultaneously. To avoid measurement problems and to get a simple structure, the brake controller and the throttle controller are designed using Lyapunov redesign method and multiple sliding mode control respectively. Through the hybrid use of brake and throttle controllers, the vehicle is insensitive to the variation of the vehicle mass, brake gain and road condition and can achieve the required acceleration performance. The proposed method is validated with simulations based on 15 DOF passenger car model.

• 전기학회논문지
• /
• 제64권1호
• /
• pp.165-170
• /
• 2015

In this paper, The strength and driving characteristics of it were investigated according to developing the traction motor for 8200 electric locomotive series. For this purpose, Flux density strength was analyzed and then structural strength was investigated such as a stator frame, design of the rotor shaft bearing according to the design process. In addition, the traction motor operating point was analyzed according to slip frequency variation at a power source frequency. As the results of analysis on torque-speed characteristic curve, we was confirmed that traction motor was controlled as torque control prior to motor speed 1610[rpm], power control between 1610[rpm] and 2500[rpm] and breakdown torque control more than motor speed 2500[rpm].

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제2B권4호
• /
• pp.207-213
• /
• 2002

The paper introduces a switched reluctance motor drive system based on an 80C31 and an Intel 80C 196KB single-chip microprocessor control. Advance schemes are used in turn-on and turn-off angles with the power converter's main switches during traction and regenerative braking. The principles of traction speed control and braking torque control are given. The hardware and software patterns in the 80c31 and the Intel 80C196KB single-chip microprocessor control system are also presented.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.680-683
• /
• 1996

The dynamics of the vehicle system has highly nonlinear components such as an engine, a torque converter and variable road condition. This thesis proposes a Fuzzy Logic Algorithm that shows better control performance than Antiwindup PI in the highly nonlinear vehicle system. Traction Control System(TCS), which adjusts throttle valve opening by Fuzzy Logic Algorithm improves vehicle drivability, steerability and stability when vehicle is starting and cornering. When a throttle valve is opened at large degree, Fuzzy Logic Algorithm shows better performances like a small settling time and a small oscillation than Antiwindup PI in simulation. The decreased desired slip ratio improves steerability in the simulation when a vehicle is cornering. The Fuzzy Logic Algorithm has been tested by a 1/5-scale vehicle for tracking the constant desired velocity.

• 전자공학회논문지B
• /
• 제33B권7호
• /
• pp.21-31
• /
• 1996

An intelligent integrated control system is designed for the active steering and the left/right traction force distribution control of electric vehicles, where input-output linearization is employed. Also, a fuzzy-rule-based cornering force estimator is suggested to avoid using an uncertain highly nonlinear expression, and a neural network compensator is additively utilized for the estimator to correctly find cornering forece. With these techniques, the proposed control system is shown by simulation results to be robust against drastic change of the external environments such as road conditions.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제51권1호
• /
• pp.40-47
• /
• 2002

This paper describes a re-adhesion control method for the Korean High-Speed Train (KHST) with parallel induction motor drive. To keep a traction efficiency and to improve vehicle maintenance, the adhesion characteristics between wheel and rail are analyzed. Also the re-adhesion controller is designed as the subsystem of induction motor vector control. In order to verify performance of the proposed control techniques, the simulation is executed by train model and a downscaled re-adhesion control simulator is utilized. Both simulation and running test results show that good re-adhesion characteristics are obtained.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1999년도 추계학술대회 논문집
• /
• pp.288-295
• /
• 1999

This paper presents an application of vector control strategy for 1.2MVA IGBT traction drive for electric railway vehicle. The vector control requires the control of the phase and amplitude of output voltage vector[5]. But in case of traction system far railway vehicle, the one-pulse mode is used in order to utilize the link voltage fully[8]. So it is impossible to control the flux axis current and the torque axis current instantaneously and independently. So this paper proposes the vector control strategy with slip-frequency control at one-pulse mode. And precise switching technique between the two different control structures has been proposed. And the strategy was verified by experimental result with 1.2MVA IGBT inverter with four 210㎾ induction motors.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.1724-1726
• /
• 2003

Korean High-Speed Train (350km/h), composed of 2 power cars, 2 motorized car and 3 trailer cars, has been developed and is under trial test. To verify the design requirements for the functions and traction performances of the train, KRRI (Korea Railroad Research Institute) decided to evaluate traction performances of the train during trial test. For this purpose, torque, velocity, voltage and current must be measured. KRRI has developed a measurement system that can measure vast and various signals effectively. In this paper, we introduce traction performances of Korean High-Speed Train. The traction measurement items are focused on the verification of motor block performances. Motor block consists of 2 motors. By this test, we verified traction performances of Korean High-Speed Train.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.1351-1354
• /
• 2005

Recently, as the feasibility study shows that trans-Korea railway and trans-continental railway are advantageous, interest in high speed railway system is increasing. Because railway vehicle is environment-friendly and safe compared with airplane and ship, its market-sharing increases gradually. Korean High Speed Train has been developed by KRRI for last 7 years to satisfy the need. Korean High Speed Train (350km/h), composed of 2 power cars, 2 motorized car and 3 trailer cars, has been developed and is under trial test. To verify the design requirements for the functions and traction performances of the train, KRRI (Korea Railroad Research Institute) decided to evaluate traction performances of the train during trial test. For this purpose, torque, velocity, voltage and current must be measured. KRRI has developed a measurement system that can measure vast and various signals effectively. In this paper, we introduce traction performances of Korean High Speed Train. The traction measurement items are focused on the verification of motor block performances. Motor block consists of 2 motors. By this test, we verified traction performances of Korean High Speed Train

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2000년도 추계학술대회 논문집
• /
• pp.720-726
• /
• 2000

The advance of traction motor control technology and the complexity of the traction power supply system makes the simulation essential in determining the dimension of the traction power supply system. The conventional method, use of the simplified and/or empirical equations, becomes inadequate in optimization of the design. The simulator presented in this paper is a numerical time based simulator running on a PC. The input to the simulator includes the track data, the train characteristic, network data and operating data. Basically the simulator conducts train running simulation and loadflow study repeatedly. The principle algorithms and its output is discussed in the paper.