• International Journal of Naval Architecture and Ocean Engineering
• /
• 제7권1호
• /
• pp.100-114
• /
• 2015

This paper deploys optimization techniques to obtain the optimum hull form of KSUEZMAX at the conditions of full-load draft and design speed. The processes have been carried out using a RaPID-HOP program. The bow and the stern hull-forms are optimized separately without altering neither, and the resulting versions of the two are then combined. Objective functions are the minimum values of wave-making and viscous pressure resistance coefficients for the bow and stern. Parametric modification functions for the bow hull-form variation are SAC shape, section shape (U-V type, DLWL type), bulb shape (bulb height and size); and those for the stern are SAC and section shape (U-V type, DLWL type). WAVIS version 1.3 code is used for the potential and the viscous-flow solver. Prior to the optimization, a parametric study has been conducted to observe the effects of design parameters on the objective functions. SQP has been applied for the optimization algorithm. The model tests have been conducted at a towing tank to evaluate the resistance performance of the optimized hull-form. It has been noted that the optimized hull-form brings 2.4% and 6.8% reduction in total and residual resistance coefficients compared to those of the original hull-form. The propulsive efficiency increases by 2.0% and the delivered power is reduced 3.7%, whereas the propeller rotating speed increases slightly by 0.41 rpm.

• 대한조선학회지
• /
• 제1권1호
• /
• pp.9-16
• /
• 1964

As a pre-study for researches on powering characteristics of straight-framed V-bottom hull forms for usual commercial vessels, practicability of such a hull is investigated from viewpoints of over-all ship economy. For this purpose, a trawler hull of straight-elements with double chines, SV(T)-1, similar to Prof. Nevitt's W-8 in size and hull form coefficients was designed and tested at the SNU Ship Model Towing Tank for resistance measurements. The result is given in Fig.3 together with those of W-8 and other equivalent hulls of double curvature, such as FAO 135a-173, Doust and Takgi. The curves of the latters are reproduction of Prof. Nevitt's analysis, and given for comparison purpose. With in speed range of $9.0{\sim}10.5$ konts the resistance coefficients of SV(T)-1 are $18{\sim}25%$ higher than those of W-8, and $5{\sim}20%$ and $12{\sim}14%$ higher than those of FAO 135a-173 and Doust respectively. SV(T)-1, however, is slightly superior in resistance characteristics than Takagi's equivalent hull within the speed range. On the other hand, an equation for reduction rates of hull construction cost required to compensate for propulsion power increase in straight-elements hulls was derived from the definition of the economic efficiency of commercial vessels. The solution of the equation is given in Fig.4 graphically, from which it is known that $10{\sim}20%$ increase in propulsion power can be compensated by $8{\sim}16%$ reduction in hull construction cost. Considering simplicity and less equipments required in construction of straight -elements hulls, the author does argue for attainability of the above reduction rates in hull construction cost. Consequently, it is concluded that there is clear feasibility to adopt straight-elements hulls for usual commercial vessels of medium and small-size. And a further research will be done to obtain reliable data for chine shapes having good flowliness with the flow around ships depending on ship's size and speed.

• 대한조선학회논문집
• /
• 제42권3호
• /
• pp.197-204
• /
• 2005

A waterjet propulsion system has many advantages compared with a conventional screw propeller especially for amphibious armored wheeled vehicles because of a good maneuverability at low speed, good operation ability at shallow water, high thrust at low speed to aid maneuverability and exit from water, etc. The POD type waterjet is adequate for the present wheeled vehicle because the weight is lighter and L/B is longer than the conventional armored amphibious vehicle. Resistance and self-propulsion tests with a 1/3.5-scale model are conducted at PNU towing tank. Based on these measurements, the performance is analyzed according to ITTC 96 standard analysis method and also according to the conventional propulsive factor analysis method. Based on these two methods, the full-scale effective and delivered powers of amphibious armored wheeled vehicle are estimated. This paper emphasizes the analysis method of model test of the waterjet propulsion system for a amphibious armored wheeled vehicle and the model test technique together with the comparison of the two analysis methods.

• 한국해양공학회지
• /
• 제29권6호
• /
• pp.436-444
• /
• 2015

A submerged body is sensitive to changes in the roll moment because of the small restoring moment and moment of inertia. Thus, a method for predicting the roll-related hydrodynamic coefficients is important. This paper describes a deduction method for the hydrodynamic coefficients based on the results of a coning motion test. A resistance test, static drift test, and coning motion test were performed to obtain the coefficients in the towing tank of Seoul National University. The sum of the hydrodynamic force, inertial force, gravity, and buoyancy was measured in the coning motion test. The hydrodynamic force was deduced by subtracting the inertial force, gravity, and buoyancy from the measured force. The hydrodynamic coefficients were deduced using the regression method.

• 한국해양공학회지
• /
• 제29권6호
• /
• pp.418-426
• /
• 2015

Recently, shipping operators have been making efforts to reduce the fuel cost in various ways, such as trim optimization and bulb re-design. Furthermore, IMO restricts the hydro-dioxide emissions to the environment based on the EEDI (Energy Efficiency Design Index), EEOI (Energy Efficiency Operational Indicator), and SEEMP (Ship Energy Efficiency Management Plan). In particular, ship speed is one of the most important factors for calculating the EEDI, which is based on methods suggested by ITTC (International Towing Tank Conference) or ISO (International Standardization Organization). Many shipbuilding companies in Korea have carried out speed trials around the Korea Straits. However, the conditions for these speed trials have not been exactly the same as those for model tests. Therefore, a ship’s speed is corrected by measured environmental data such as the seawater temperature, density, wind, waves, swell, drift, and rudder angle to match the conditions of the model tests. In this study, fundamental research was performed to evaluate the ship resistance performance due to changes in the water temperature and salinity, comparing the ISO method and numerical simulation. A numerical simulation of a KCS (KRISO Container ship) with a free-surface was performed using the commercial software Star-CCM+ under three conditions that were assumed based on the water temperature and salinity data in the Korea Straits. In the simulation results, the resistance increased under low water temperature & high salinity conditions, and it decreased under high water temperature & low salinity conditions. In addition, the ISO method showed the same result as the simulation.

• Ocean Systems Engineering
• /
• 제10권1호
• /
• pp.87-110
• /
• 2020

Catamaran has recently been a choice to support a typical vertical axis turbine in floating tidal current energy conversion system. However, motion responses associated with the catamaran can reduce the turbines efficiency. The possibility to overcome this problem isto change the catamaran parameter by varying and simulating the demi-hull separations to have lower motion responses. This simulation was undertaken by Computational Fluid Dynamic (CFD) using potential flow analysis. Cases of demi-hull separation were considered, with ratios of demi-hull separation (S) to the breadth of demi-hull (B), ^S/_B of 3.45, 4.95, 6.45, 7.2 and 7.95. In order to compare to the previous works in the literature, the regular wave was set with wave height of 0.8 m. Furthermore, the analysis was carried out by irregular waves with significant wave height, H_s, of about 0.09 to 1.5 m and the wave period, T, of about 1.5 to 6 s or corresponding to the wave frequency, ω, of about 1.1 to 4.2 rad/s. The wave spectrum was derived from the equation of the International Towing Tank Conference (ITTC). For the case of turbines-loaded catamaran under consideration, the new finding is that the least significant amplitude response can be satisfied at the ratio ^S/_B of 7.2. This study indicates that selecting a right choice of demi-hull separation ratio could contribute in reducing motion responses of the tidal current turbines-loaded catamaran.

• 대한조선학회논문집
• /
• 제28권2호
• /
• pp.318-328
• /
• 1991

본고는 진동수주(Oscillating Water Column:OWC)와 에어터어빈으로 구성된 고정식 파력발전장치의 특성파악을 위한 실험적 연구를 다루고 있다. 실험의 단순화를 위하여 에어터어빈은 이에 등가한 압력강하를 주는 와이어메쉬 스크린으로 대치하여 챔버내 공기유동 및 파랑운동간의 상호작용을 시뮬레이션하였다. 실험은 예인수조에 설치된 조파기를 이용하여 주파수 범위 0.22-0.75Hz인 규칙파 중에서 실시되었다. 실험결과는 홍도천 등 [4]의 2차원 포텐시얼 수치해석결과와 비교되었으며, 상호 잘 일치된 결과를 줌을 확인할수 있었다. 와이어메쉬 스크린을 사용한 공기터어빈의 시뮬레이션 결과로부터 OWC챔버에 미치는 스크린의 영향은 본 연구에서 설정한 실험범위 내에서는 무시할 만한 것으로 나타났다. 정성적으로 볼때 본 형상을 갖는 약 6m정도의 시제품을 제작한다면 주파수 0.3Hz 이내의 해양파중에서 실제 사용이 가능할 것으로 여겨진다.

• Journal of Ship and Ocean Technology
• /
• 제12권1호
• /
• pp.16-27
• /
• 2008

The interaction between advancing ships and the waves generated by them plays important roles in wave resistances and ship motions. Wave breaking phenomena near the ship bow at different speeds are investigated both numerically and experimentally. Numerical simulations of free surface profiles near the fore bodies of ships are performed and visualized to grasp the general trend or the mechanism of wave breaking phenomena from moderate waves rather than concentrating on local chaotic irregularities as ship speeds increase. Navier-Stokes equations are differentiated based on the finite difference method. The Marker and Cell (MAC) Method and Marker-Density Method are employed, and they are compared for the description of free surface conditions associated with the governing equations. Extra effort has been directed toward the realization of extremely complex free surface conditions at wave breaking. For this purpose, the air-water interface is treated with marker density, which is used for two layer flows of fluids with different properties. Adaptation schemes and refinement of the numerical grid system are also used at local complex flows to improve the accuracy of the solutions. In addition to numerical simulations, various model tests are performed in a ship model towing tank. The results are compared with numerical calculations for verification and for realizing better, more efficient research performance. It is expected that the present research results regarding wave breaking and the geometry of the fore body of ship will facilitate better hull form design productivity at the preliminary ship design stage, especially in the case of small and fast ship design. Also, the obtained knowledge on the impact due to the interaction of breaking waves and an advancing hull surface is expected to be applicable to investigation of the ship bow slamming problem as a specific application.

• 대한조선학회논문집
• /
• 제57권3호
• /
• pp.133-139
• /
• 2020

In order to study the resistance test technique for the submerged body in Large Cavitation Tunnel (LCT), DARPA Suboff, submarine model publicly available was manufactured. DTRC released the resistance test data of DARPA Suboff conducted at ship speeds up to 18.0 knots in high-speed towing tank in 1990. As LCT is considered restricted waterways with walls, the resistance test results must be corrected with three wall blockage effects called buoyancy effect, solid blockage effect and wake blockage effect. Before correction, the resistance of LCT was 16~20 % higher than that of DTRC. After correction, the resistance and the resistance coefficients were compared with those of DTRC. The corrected resistance of LCT shows good agreement with that of DTRC. The residual resistance coefficient shows the difference according to the calculation method of buoyancy and frictional resistance coefficient. This paper suggests the best way for the calculation of residual resistance coefficient, On the basis of the present study, it is thought that the operating conditions for the propeller cavitation and noise tests can be drawn through LCT tests.

• 대한조선학회논문집
• /
• 제47권6호
• /
• pp.757-762
• /
• 2010

Korean fishing boats have had appropriate hull forms for the safety, stability and convenience of fishing ability. However, Korean fishermen are recently concerned about the resistance performance and speed of Korean fishing boats, because the prices of fuel oil are gradually risen, also the exhausting of fish resources and the demand of high speed fishing boats are increased. Therefore, the necessity of the study on the improvement of resistance performance for Korean small coastal fishing boats is gradually increased. This study compares the hull form characteristics of Korean fishing boats with those of Japanese fishing boats, and the hull form of a representative Korean fishing boat is modified. From the modification of the hull form parameters for the Korean fishing boat, the improvement of resistance performances is evaluated. Moreover, the increase of resistance performances is also achieved from the modification of local characteristics for the hull form of the Korean fishing boat. A computational method and ship model tests in towing tank are used for the conformations of the improvement of resistance performance.