• 한국토양비료학회지
• /
• 제43권4호
• /
• pp.478-483
• /
• 2010

전라북도 장수군 오미자 과원을 대상으로 토양의 이 화학적 특성을 조사하여 오미자의 품질향상, 수량증대 및 유해물질 종합관리 시스템 구축을 위한 기초조사를 수행하였다. 오미자 재배과원 토양은 대부분 양질사토였으며, 토양입단화도는 약 33.12%로 입단의 발달이 부족한 상태였으며, 토양공극율은 약 60% 수준으로 적당한 것으로 나타났다. 토양 pH는 평균 5.51이었으며, 양이온교환용량은 평균 4.11 $cmol_c\;kg^{-1}$으로 매우 낮게 나타났다. 식물영양성분은 적정 수준으로 유지되고 있었으나, 장수군 오미자 재배지 토양의 이화학적 특성 개량을 위해서는 유기물 및 석회처리 등의 토양관리가 필요한 것으로 나타났다. 조사대상 중금속의 함량은 자연함유량 수준으로 중금속 오염으로 인한 작물 안정성은 확보된 것으로 조사되었다.

• 한국세라믹학회지
• /
• 제55권2호
• /
• pp.153-159
• /
• 2018

Porous ceramic plates were prepared from Onggi clay and bamboo charcoal powder at 1100 and $1200^{\circ}C$ and their porous properties and water absorption, and the cooling effect of porous plates, were investigated to produce eco-friendly porous ceramics for a self-cooling system that relies on the evaporation of absorbed water. Porous properties were dependent on the particle size of charcoal powder pore forming additive and the firing temperature; properties were also found to be dependent on the total pore volume, average pore size and porosity, which had values of $0.103-0.243cm^3/g$, 0.81 - 2.56 mm and 20.9 - 38.2%, respectively, at $1100^{\circ}C$ and $0.04-0.18cm^3/g$, 0.33 - 2.03 mm and 10.8 - 30.9%, respectively, at $1200^{\circ}C$. Cooling temperature difference of flowing air parallel to surface of porous ceramic plates fired with two kinds of charcoal powder at $1100^{\circ}C$ was $3.5-3.6^{\circ}C$ at $26^{\circ}C$ and 60% of relative humidity in a closed box. Cooling temperature difference was dependent on the number of porous plates and the distance between porous plates. A simple and eco-friendly cooling system using porous ceramic plates fired from Onggi clay and charcoal powder was proposed.

• 대한치과보철학회지
• /
• 제38권1호
• /
• pp.12-25
• /
• 2000

To demonstrate possible influences of general bone density on the mandible, histomorphometric analysis was carried out in mandibles and iliac bones and the correlation of the two bone densities was tested. Comparison of bony density in women and men over 60 years in the mandible was carried out too. Quantitative computed tomography(QCT) was taken in cross-section of mandibles at the same site where histomorphometric analysis was peformed to evaluate the reliability of QCT. The analysis included 40 cadavers with no known diseases affecting the bones. The subjects consisted of 15 females and 25 males with a mean age of 60.3 years. Spearman correlation analysis and Wilcoxon rank sum test was performed. The results were as follows. 1. There was statistically no correlation between the mandible and iliac bone in the values of corrected cortical width(CCW), cortical porosity(POR) in cortex, and total bone volume(TBV), mean trabecular plate thickness(MTPT), mean trabecular plate density(MTPD), and mean trabecular plate separation(MTPS) in trabecular bone. 2. Comparison of women and men over 60 years, men had statistically higher bone density than women except fir POR of buccal and lingual cortex, and WTPD of alveolar trabeculae in mandible. 3. There was statistically significant correlation between TBV of trabecular bone and CT No., but not between POR and CT No. in mandible. According to the results above, there was no correlation between mandible and iliac bone density and between mandibular bony density and age. Further studies are required to support the results. A more noninvasive method to be able to measure the bone density of mandible should be developed and it is necessary to accumulate data on the normal values of bone density of mandible according to age and sex. Further study should be carried out about QCT to measure mandibular bony density using QCT.

• 한국결정성장학회지
• /
• 제28권2호
• /
• pp.74-79
• /
• 2018

내부식성이 약해서 응용이 제한되고 있는 Mg 합금 AZ31과 AZ91의 내부식성을 향상시키기 위하여 Na-P 및 Na-Si 전해액을 사용하여 공정조건에 따라 PEO 처리를 하여 표면 피막의 결정상과 morphology를 관찰하였다. PEO 처리한 표면 산화피막에서 가장 흔히 발견되는 결정상은 MgO이며 비정질상의 존재도 알 수 있었다. 전해액에서부터 비롯된 Na, P 및 Si 성분이 산화피막의 형성에 첨가되어 $Na_{3.59}Mg_{2.71}(PO_4)_3$ 상과 $Mg_2SiO_4$ 결정상이 관찰되었다. 산화표면은 PEO 처리 전압, 전해질 농도, 처리 시간에 따라서 기공율이 감소하다가, 이후 기공율과 기공의 크기가 증가하는 경향을 관찰할 수 있었다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.457-464
• /
• 2005

In the case of tunneling, the equilibrium state of hydro-geologic environments destroy and change abruptly in some section of whole works. Specially, it's very possible for seawater to intrude toward the site of tunnel if the field is nearly located in a costal region. In this study, we have evaluated the mechanism related between groundwater flow and seawater intrusion that by impacts of tunneling. Various hydro-geological field tests have performed for getting four representative hydrogeologic properties of geologic formations such as transmissivity (T), storativity(S), longitudial dispersity(${\alpha}_L$), and effective porosity($n_e$). For the effect of tunneling, the numerical model was first simulated based on the governing equation of groundwater flow. The results showed that the maximum drawdown was 17.2m and the total inflow into the tunnel had the range from 0.48 to $3.63m^3/day/m$. Secondly, the three dimensional numerical model was analyzed to investigate a characteristic of seawater intrusion based on the previous simulated results of groundwater flow. The results showed the seawater moved as the range of $200{\sim}220m$ from the initial interface between seawater and groundwater toward the tunnel.

• 대한기계학회논문집B
• /
• 제39권7호
• /
• pp.625-631
• /
• 2015

이번 연구는 패킹 모듈로 채워진 축열조의 방열 성능을 수치해석 하였다. 해석에는 PCM의 상변화 현상을 계산하기 위해 엔탈피-공극률 방법을 이용하였다. 이 방법을 통해서 방열 시 축열조 상부로부터 열전달유체가 흐를 때 모듈에서의 녹는 현상을 계산하였다. 축열조 디자인에 모듈 배치, 모듈 수 등의 다양한 인자가 있지만, 본 해석에서는 유량의 변화에 따라 나타나는 축열조 출구온도, 전체 PCM의 시간에 따른 녹은 양 및 축열밀도를 확인하였다. 결과적으로 유량이 증가할수록 출구온도가 높게 형성되었으며, 전체 PCM이 녹는데 필요한 시간이 짧아지고 축열 밀도 역시 증가하여 목표치의 93% 수준에 도달하는 것으로 나타났다.

• Carbon letters
• /
• 제10권2호
• /
• pp.114-122
• /
• 2009

Crushed, depitted peach stones were impregnated activated with 50% $H_3PO_4$ followed by pyrolysis at $500^{\circ}C$. Two activated carbons were produced, one under its own evolved gases during pyrolysis, and the second conducted with air flow throughout the carbonization stage. Physicochemical properties were investigated by several procedures; carbon yield, ash content, elemental chemical analysis, TG/DTG and FTIR spectra. Porosity characteristics were determined by the conventional $N_2$ adsorption at 77 K, and data analyzed to get the major texture parameters of surface area and pore volume. Highly developed activated carbons were obtained, essentially microporous, with slight effect of air on the porous structure. Oxygen was observed to be markedly incorporated in the carbon matrix during the air treatment process. Cation exchange capacity towards Cu (II) and Cd (II) was tested in batch single ion experimental mode, which proved to be slow and a function of carbon dose, time and initial ion concentration. Copper was up taken more favorably than cadmium, under same conditions, and adsorption of both cations was remarkably enhanced as a consequence of the air treatment procedure. Sequestration of the metal ions was explained on basis of the combined effect of the oxygen functional groups and the phosphorous-containing compounds; both contributing to the total surface acidity character.

• International Journal of Korean Welding Society
• /
• 제2권2호
• /
• pp.26-31
• /
• 2002

Considering the fuel consumption of car, a light structure of aluminum alloys is desired fer car body nowadays. However, fusion welding of aluminum alloys has some problems of reduction of joint efficiency, porosity formation and hot cracking. In the present work, investigation to improve the joint performance of laser welded joint has been carried out by addition of Cu, Ni, and Zr to A6NO 1 alloy welds. Aluminum alloy plate of 2.Omm in thickness with filler metal bar was welded by twin beam Nd: YAG laser facility (total power: 5kW). The filler metals were prepared by changing the chemical compositions for adding the elements into the weld metal. Thirteen filler metal bars were prepared and pre-placed into the base metal before welding. Ar gas shielding with a flow rate of 10 1/min was used. The defocusing distance is kept at 0 mm. At travel speeds off 3 to 9 and at laser power of 5kW (front beam 2kW rear beam 3kW), full penetration welds were obtained, whereas at travel speeds of 12 to 18 m/min and same power, partial penetration was observed. The joint efficiency of laser-welded joint was improved by the addition of Cu, Ni, and Zr due to the solid solution hardening, grain refining and precipitation hardening. The type of hardening has been further considered by metallurgical examination.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2003년도 춘계학술발표논문집
• /
• pp.70-79
• /
• 2003

Paper coating can give smoothness surface and good printability to uncoated paper. Macro roughness of base paper would be decreasing its groove and grit in view of side. Nevertheless its improving effect for paper, some kind of problem is showing in the fine coated paper. Especially, back trap mottle is one of serious problems in printing with fine coated paper. Printers can not adjust conditions to overcome the problem. Also large amounts of paper can be rejected. There are many factors that influence back trap mottle. However it is not clear what the important parameters are in back trap mottle. Back trap mottle has some relationship with ink setting but good guidelines are not clear. Back trap mottle has been linked to non-uniform ink setting. We do not know how much variation in setting we can tolerate. Other mottle issues such as micro-picking and ink refusal are still common. This paper was prepared to identify correlation with ink setting and delta ink density obtained from experiment and then tried to find out some relationships with ink setting and back trap mottle. Basically fine calcium carbonate and ciay was used for main components and coarse calcium carbonate was mixed in two fine pigments to change its porosity and ink acceptance. Micro ink tack force at KRK printing tester was adapted to measure ink setting rate. KRK units were used for back trap mottle simulation and two printed samples were prepared to check delta ink density. Clay base coating has more fast ink setting time than calcium carbonate's though smoothness of clay was better than calcium carbonate. It could be explained by that clay has finer pore in its coating than calcium carbonate. DID(delta ink density) has shown a good correlation with ink setting time from micro ink tack. The total pore volume of coating layer did not match with ink setting and DID. From the results we might conclude coating that has fine pore size around 0.05 ${\mu}m$ can be exposed to high possibility of back trap mottle.

• 한국환경농학회지
• /
• 제17권2호
• /
• pp.170-173
• /
• 1998

신천하수종말처리장에서 발생한 슬러지를 처리별로 시용한 다음 토양의 이화학성(理化學性)과 중금속 함량변화를 조사하였다. 슬러지 시용량이 증가함에 따라 질소, 인산 및 무기염류의 함량이 증가하는 것으로 나타 났으며, 토양의 입단화, 공극률 및 투수성이 증가하였으며 경도는 감소하였다. 중금속 함량은 Cr, Zn의 경우 약간의 증가를 보였으며,함류량이 적어 시용량이 증가하여도 함량에 차이가 없으며, 하층으로 이동하거나 용탈하지 않는 것으로 나타났다. Sludge중 중금속 함량이 매우 낮음으로 sludge의 처리가 토양 중금속 함량에 별다른 영향을 주지 않았다.따라서 토양의 하부(下部)로 이동하는 현상도 나타나지 않았다.