• 한국자동차공학회논문집
• /
• 제15권6호
• /
• pp.50-61
• /
• 2007

The structural stiffness, strength and stability on the bodyshell and floor structures of the Korean Low Floor Bus composed of laminate, sandwich panels and metal reinforced frame were evaluated. The laminate composite panel and facesheet of sandwich panel were made of WR580/NF4000 glass fabric/epoxy laminate, while aluminum honeycomb or balsa was applied to the core materials of the sandwich panel. A finite element analysis was used to verify the basic design requirements of the bodyshell and the floor structure. The use of aluminum reinforced frame and honeycomb core was beneficial for weight saving and structural performance. The symmetry of the outer and inner facesheet thickness of sandwich panels did not affect the structural integrity. The structural strength of the panels was evaluated using Von-Mises criterion for metal structures and total laminate approach criterion for composite structures. All stress component of the bodyshell and floor structures were safely located below the failure stresses. The total laminate approach is recommended to predict the failure of hybrid sandwich composite structures at the stage of the basic design.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 춘계학술발표대회 논문집
• /
• pp.163-167
• /
• 2001

A two-dimensional progressive failure analysis method is presented for the strength characterization of the composite joints under pin loading. The eight-nodes laminated she]1 element is utilized based on the updated Lagrangian formulation. The criteria by Yamada-Sun, Tsai-Wu, and the maximum stress are used for the failure estimation. The stiffness of failed layer is degraded by the complete unloading method. No factor depending on test is included in the finite element analysis except for the material strength and stiffness. Total 20 plate specimens with and without hole are tested to validate the finite element prediction. The Tsai-Wu failure criterion most conservatively estimates the strength of laminate, and the maximum stress criterion yields the highest strength because it does not consider the coupling of the failure modes. The strength by Yamada-Sun method neglecting the matrix failure effect are located between other two methods and shows best agreement with test result for laminate with hole.

• Composites Research
• /
• 제17권1호
• /
• pp.18-28
• /
• 2004

섬유강화 적층 복합재 차체 구조물의 강도를 평가하기 위해 전체 적층판 접근방법의 적용을 제시하였다. 180km/h급의 한국형 틸팅열차의 하이브리드 복합재 자체 기본설계를 검증하기 위해서 구조해석을 수행하였으며 또한 복합재 적층판의 강도를 구하기 위해 기계적 물성시험을 수행하였다. 결과적으로, 한국형 틸팅열차의 복합재 자체 구조물에서 발생하는 응력값들은 모두 파손영역의 안전한 범위 내에 존재하였으며 전체 적층판 접근방법은 초기 기본석계 단계에서 하이브리드 복합재 자체 구조물의 파손을 예측하는데 매우 유용함을 증명하였다.

• Structural Engineering and Mechanics
• /
• 제34권2호
• /
• pp.175-188
• /
• 2010

This paper deals with the buckling and postbuckling responses, and the progressive failure of square laminates of symmetric lay-up with a central rectangular cutout under in-plane shear load. A detailed investigation is made to show the effects of cutout size and cutout aspect ratio on the buckling and postbuckling responses, failure loads and failure characteristics of $(+45/-45/0/90)_{2s}$, $(+45/-45)_{4s}$ and $(0/90)_{4s}$ laminates. The 3-D Tsai-Hill criterion is used to predict the failure of a lamina while the onset of delamination is predicted by the interlaminar failure criterion. In addition, the effects of boundary conditions on buckling loads, failure loads, failure modes, and maximum transverse deflection for a $(+45/-45/0/90)_{2s}$ laminate with and without a square cutout have been presented. It is concluded that because of early onset of delamination at the net section of cutouts before first-ply failure, total strength of the laminate with very small cutouts can not be utilized.

• Structural Engineering and Mechanics
• /
• 제5권4호
• /
• pp.433-450
• /
• 1997

The objective of this work is to predict the failure loads, associated maximum transverse displacements, locations and the modes of failure, including the onset of delamination, of thin, flat, square symmetric laminates under the action of uni-axial compression. Two progressive failure analyses, one using Hashin criterion and the other using Tensor polynomial criteria, are used in conjunction with the finite element method. First order shear deformation theory and geometric nonlinearity in the von Karman sense have been employed. Five different types of lay-up sequence are considered for laminates with all edges simply supported. In addition, two boundary conditions, one with all edges fixed and other with mixed boundary conditions for $(+45/-45/0/90)_{2s}$ quasi-isotropic laminate have also been considered to study the effect of boundary restraints on the failure loads and the corresponding modes of failure. A comparison of linear and nonlinear results is also made for $({\pm}45/0/90)_{2s}$ quasi-isotropic laminate. It is observed that the maximum difference between the failure loads predicted by various criteria depend strongly on the laminate lay-ups and the flexural boundary restraints. Laminates with clamped edges are found to be more susceptible to failure due to the transverse shear and delamination, while those with the simply supported edges undergo total collapse at a load slightly higher than the fiber failure load.

• Structural Engineering and Mechanics
• /
• 제6권2호
• /
• pp.143-159
• /
• 1998

The objective of this present work is to estimate the failure loads, associated maximum transverse displacements, locations and the modes of failure, including the onset of delamination, of thin, square symmetric laminates under the action in-plane positive (+ve) shear load. Two progressive failure analyses, one using the Hashin criterion and the other using a Tensor polynomial criterion, are used in conjunction with finite element method. First order shear deformation theory along with geometric non-linearity in the von Karman sense have been employed. Variation of failure loads and failure characteristics with five type of lay-ups and three types of boundary conditions has been investigated in detail. It is observed that the maximum difference between failure loads predieted by various criteria depends strongly on the laminate lay-up and the flexural boundary restraint. Laminates with clamped edges are found to be more susceptible to failure due to transverse shear (ensuing from the out of plane bending) and delamination, while those with simply supported edges undergo total collapse at a load slightly higher than the fiber failure load. The investigation on negative (-ve) in-plane shear load is in progress and will be communicated as part-II of the present work.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2002년도 봄 학술발표회 논문집
• /
• pp.319-326
• /
• 2002

A p-version finite element model based on degenerate shell element is proposed for the analysis of orthotropic laminated plates. In the nonlinear formulation of the model, the total Lagrangian formulation is adopted with large deflection and moderate rotation being accounted for in the sense of von Karman hypothesis. The material model Is based on the Huber-Mises yield criterion and Prandtl-Reuss flow rule in accordance with the theory of strain hardening yield function, which is generalized for anisotropic materials by introducing the parameters of anisotropy. The model is also based on extension of equivalent-single layer laminate theory(ESL theory) with shear deformation, leading to continuous shear strain at the interface of two layers. The Integrals of Legendre Polynomials we used for shape functions with p-level varying from 1 to 10. Gauss-Lobatto numerical quadrature is used to calculate the stresses at the nodal points instead of Gauss points. The validity of the proposed p-version finite element model is demonstrated through several comparative points of view in terms of ultimate load, convergence characteristics, nonlinear effect, and shape of plastic zone

• 한국전산구조공학회논문집
• /
• 제15권3호
• /
• pp.491-499
• /
• 2002

직교이방성 적층평판해석을 위해 퇴화 쉘요소에 기초를 둔 p-version 유한요소법이 제안되었다. 이 모델의 비선형 정식화과정에서 기하비선형의 경우 von Karman의 대변형-소변형률 가정을 설명하기 위해 Total Lagrangian 방법이 채택되었으며, 재료비선형의 경우 Huber-Mises의 항복기준과 변형률경화 항복함수에 근거를 둔 Prandtl-Reuss 유동법칙이 사용되었다. 재료모델은 이방성을 표현하는 매개변수에 의해 이방겅재료를 고려할 수 있도록 하였다. 적층평판이론으로는 전단변형 효과를 고려할 수 있는 등가단출이론(ESL Theory)에 기초를 두었기 때문에 두 적층간 계면에서의 전단변형률은 연속이라는 조건을 갖게된다 적분형 르장드르 다항식이 형상함수로 사용되었으며 형상함수의 차수는 1차에서 10차까지 변화시킬 수 있다. 또한, Causs-Lobatto 수치적될법을 사용하기 때문에 기존의 가우스 적분점에서 계산되던 응력값은 이 적분법의 적분점이 절점에 위치하므로 절점에서 바로 응력값이 산출되도록 하였다 극한하중 수렴성, 비선형 효과, 소성역의 형상 등의 비교관점을 통해 p-version 유한요소 모델의 적정성을 보이고자 하였다.