• 대한토목학회논문집
• /
• 제29권6C호
• /
• pp.251-258
• /
• 2009

본 연구에서는 모래다짐말뚝 (SCP)로 개량된 연약점토지반상의 성토시공에 있어서 최적설계조건에 대해 현행 설계법과 손실평가함수 및 1차 근사 2계 모멘트법 (AFOSM)에 기초한 신뢰성 설계법으로 비교 검토하였다. 결과를 요약하면 다음과 같다. 1) 안전율(Fs)와 파괴확률($P_F$)는 심한 비선형 관계를 나타냈고, Fs가 1.2로 증가함에 따라 $P_F$는 약 1%까지 급격한 감소를 나타낸 후, 안전율의 증가와 더불어 $P_F$는 점진적으로 감소하였다. 현행 설계법상의 기준 안전율 1.2는 둘의 관계에 있어서 일종의 임계값이며, 이들의 관계가 적절히 고려되어 정립되었다고 판단된다. 2) 최소기대총비용을 나타내는 안전율은 1.15부근으로 현행설계기준 1.2에 다소 못미치는 값으로 나타났고, 파괴확률은 1% 정도로 다소 컸다. 3) 응력분담비 n과 모래의 내부마찰각 ${\phi}$의 민감도가 연약층의 초기비배수강도 관련 변수들의 민감도보다 더 크게 나타났다. 이것은 n과 ${\phi}$의 변동 특성이 보다 해석결과에 큰 영향을 준다는 것과 이들 변동 특성은 SCP 개량지반상의 성토안정해석에 반드시 고려되어야 함을 의미한다. 4) 설계기준안전율 1.2 이상(파괴확률 0.1-0.3% 이하)에서 New Failure Point는 평균치에서 표준편차의 1~2배 가량 떨어져 있는 값을 나타냈다.

• 대기
• /
• 제25권2호
• /
• pp.221-233
• /
• 2015

Pollen is closely related to health issues such as allergenic rhinitis and asthma as well as intensifying atopic syndrome. Information on current and future spatio-temporal distribution of allergenic pollen is needed to address such issues. In this study, the Community Multiscale Air Quality Modeling (CMAQ) was utilized as a base modeling system to forecast pollen dispersal from oak trees. Pollen emission is one of the most important parts in the dispersal modeling system. Areal emission factor was determined from gridded areal fraction of oak trees, which was produced by the analysis of the tree type maps (1:5000) obtained from the Korea Forest Service. Daily total pollen production was estimated by a robust multiple regression model of weather conditions and pollen concentration. Hourly emission factor was determined from wind speed and friction velocity. Hourly pollen emission was then calculated by multiplying areal emission factor, daily total pollen production, and hourly emission factor. Forecast data from the KMA UM LDAPS (Korea Meteorological Administration Unified Model Local Data Assimilation and Prediction System) was utilized as input. For the verification of the model, daily observed pollen concentration from 12 sites in Korea during the pollen season of 2014. Although the model showed a tendency of over-estimation in terms of the seasonal and daily mean concentrations, overall concentration was similar to the observation. Comparison at the hourly output showed distinctive delay of the peak hours by the model at the 'Pocheon' site. It was speculated that the constant release of hourly number of pollen in the modeling framework caused the delay.

• 설비공학논문집
• /
• 제27권4호
• /
• pp.195-200
• /
• 2015

The thermal performance in the channels with two-wall rectangular convergent/divergent cross-sectional areas along the axial distance was investigated experimentally. The ribbed rectangular convergent/divergent channels were manufactured with a fixed rib height (e) = 10 mm and the ratio of rib spacing (p) to height (e) = 10. Three different parallel angled ribs (a = $30^{\circ}$, $45^{\circ}$, and $60^{\circ}$) were each placed on the channel's one sided wall only. The convergent channel of $D_{ho}/D_{hi}=0.67$ and the divergent channel of $D_{ho}/D_{hi}=1.49$ were considered. The ribbed divergent channel produced better thermal performance than the ribbed convergent channel in three different restrictions; identical flow rate, identical pumping power, and identical pressure loss.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권6호
• /
• pp.609-613
• /
• 2015

축방향 거리에 따라 확대되는 정사각 채널에서 발달된 난류유동의 국부 난류 열전달과 압력강하를 실험적으로 조사하였다. 정사각 확대채널에 한 면에만 높이가 10 mm인 리브를 설치하였다. 리브의 충돌 각은 $30^{\circ}$, $45^{\circ}$, $60^{\circ}$ 그리고 $90^{\circ}$로 한 벽면에 만 설치하였다. 레이놀즈수가 22,000~79,000의 범위에서 실험을 수행하였다. 연구 결과 $45^{\circ}$의 리브 충돌각이 가장 우수한 열전달 성능을 보였다.

• 설비공학논문집
• /
• 제18권1호
• /
• pp.81-86
• /
• 2006

High temperature superconducting (HTS) power cable requires forced sub-cooled LN2 flow cooling. Liquid nitrogen is circulated by a pump and cooled back by cooling system. Typical operating temperature range is expected to be between 65 K and 77 K. The HTS power cable needs sufficient cooling to overcome its low temperature heat load. For successful cooling, the hydraulic characteristics of the HTS power cable must be well investigated to design the cables. Especially, the pressure drop in the cable is an important design parameter, because the pressure drop decides the length of the cable, size of the coolant circulation pump and circulation pressure, etc. This paper describes measurement and investigation of the pressure drop of the cooling system. In order to reduce the total pressure drop of the cooling system, the flow rate of liquid nitrogen must be controlled by rotational speed of the circulation pump.

• 동력기계공학회지
• /
• 제20권1호
• /
• pp.69-74
• /
• 2016

The local heat transfer and pressure drops of developed turbulent flows in the convergent channels with square cross-sectional areas along the streamwise distance have been investigated experimentally. Four different parallel angled ribs (a = $30^{\circ}$, $45^{\circ}$, $60^{\circ}$, and $90^{\circ}$) are placed to the one sided wall only, respectively. The ribbed walls are manufactured with a fixed rib height (e)=10 mm and the ratio of rib spacing (p) to height (e) = 10. The measurement was run within the range of Reynolds numbers from 22,000 to 79,000. The result shows that the increases in the Nusselt numbers for the flow attack angles can be seen in the order of $30^{\circ}$, $45^{\circ}$, $60^{\circ}$ and $90^{\circ}$.

• Journal of Mechanical Science and Technology
• /
• 제17권1호
• /
• pp.146-156
• /
• 2003

A numerical algorithm is developed to analyze the performance of a Unit-injector (UI) System for a diesel engine. The fundamental theory of the algorithm is based on the continuity equation of fluid dynamics. The loss factors that should be seriously regarded on the continuity equation are the compressibility effect of liquid fuel, the wall friction loss in high-pressure fuel lines of the system, the kinetic energy loss of fuel in the system, and the leakage of fuel out of the control volume. For an evaluation of the developed simulation algorithm, the calculation results are compared with the experimental outputs provided by the Technical Research Center of Doowon Precision Industry Co. (DPICO) ； the maximum pressure in the plunger chamber (P$\_$p/) and total amount of fuel injected into a cylinder per cycle (Q$\_$f/) at each operational condition. The result shows that the average error rate (%) of P$\_$p/ and Q$\_$f/ are 2.90% and 4.87%, respectively, in the specified operational conditions. Hence, it can be concluded that the analytical simulation algorithm developed in this study can be reasonably applied to the performance prediction of newly designed UI system.

• 대한기계학회논문집A
• /
• 제27권12호
• /
• pp.2019-2027
• /
• 2003

Pitting wear is a dominant from of polyethylene surface damage in total knee replacements, and may originate from surface cracks that propagate under repeated tribological contact. In this study, stress intensity factors, K$\_$I/and $_{4}$, were calculated for a surface crack in a polyethylene-CoCr-bone system under the rolling and/or sliding contact pressures. Crack length and load location were considered in determination of probable crack propagation mechanisms and fracture modes. Positive K$\_$I/ values were obtained for shorter cracks in rolling contact and for all crack lengths when the sliding load was apart from the crack. $_{4}$ was the greatest when the load was directly adjacent to the crack (g/a=${\pm}$1). Sliding friction caused a substantial increase of both K$\_$I/$\^$max/ and $_{4}$$\^$max/. The effective Mode I stress intensity factors, K$\_$eff/, were the greatest at g/a=${\pm}$1, showing the significance of high shear stresses generated by loads adjacent to surface cracks. Such behavior of K$\_$eff/ suggests mechanisms for surface pitting by which surface cracks may propagate along their original plane under repeated rolling or sliding contact.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1222-1227
• /
• 2003

Pitting wear is a dominant form of polyethylene surface damage in total knee replacements, and may originate from surface cracks that propagate under repeated tribological contact. In this study, stress intensity factors, $K_{I}$ and $K_{II}$, were calculated for a surface crack in a polyethylene - CoCr - bone system under the rolling and/or sliding contact pressures. Crack length and load location were considered in determination of probable crack propagation mechanisms and fracture modes. Positive $K_{I}$ values were obtained for shorter cracks in rolling contact and for all crack lengths when the sliding load was apart from the crack. $K_{II}$, was the greatest when the load was directly adjacent to the crack $(g/a={\pm}1)$. Sliding friction caused a substantial increase of both $K_{I}^{max}$ and $K_{II}^{max}$. The effective Mode I stress intensity factors, $K_{eff}$, were the greatest at $g/a={\pm}1$, showing the significance of high shear stresses generated by loads adjacent to surface cracks. Such behavior of $K_{eff}$ suggests mechanisms for surface pitting by which surface cracks may propagate along their original plane under repeated rolling or sliding contact.

• 상하수도학회지
• /
• 제34권3호
• /
• pp.221-230
• /
• 2020

In actual seawater desalination plant, the pressure loss due to frictional force of pipe is about 3~5 bar. Also, the pressure loss at pipe connection about 1~3 bar. Therefore, the total pressure loss in the pipe is expected to be about 4~8 bar, which translates into 0.111 to 0.222 kWh/㎥ of energy when converted into the Specific Energy Consumption(SEC). Reducing energy consumption is the most important factor in ensuring the economics of seawater desalination processes, but pressure loss in piping is often not considered in plant design. It is difficult to prevent pressure loss due to friction inside the pipe, but pressure loss at the pipe connection can be reduced by proper pipe design. In this study, seawater desalination plant piping analysis was performed using a commercial network program. The pressure loss and SEC for each case were calculated and compared by seawater desalination plant size.