• Radiation Oncology Journal
• /
• 제19권2호
• /
• pp.199-204
• /
• 2001

목적 : 정위방사선치료 시 정상 뇌 조직을 고선량의 방사선으로부터 최대한 보호하며 치료의 효율성을 높이기 위하여 치료 인자 중 콜리메이터의 크기와 arc 간 간격에 따른 이상적인 total arc degree (TAD) 값을 제시하고자 한다. 대상 및 방법 : XKnife-3 planning system을 사용하여 환자의 송과체 부위에 방사선 빔의 회전중심점을 위치시킨 후 12, 20, 30, 40, 50 그리고 60 mm 직경의 정위방사선치료용 원형 콜리메이터를 이용하여 각각의 콜리메이터 직경별로 TAD를 100, 200, 300, 400, 500, 600도, 그리고 arc 간 간격을 30도(6-arc system)와 45도(4-arc system)로 설정하여 방사선치료계획을 수립하였다. 치료계획을 통해 얻은 누적선량체적히스토그람을 이용하여 회전중심점 처방선량의 $50\%$ 이상 조사되는 정상 뇌의 용적$(V_{50})$ 및 적분 생물학적 유효선량(integral biologically effective dose)을 이용하여 각각의 TAD에 따른 방사선치료계획을 비교하였다. 결과 : TAD에 따른 $V_{50}$의 변화는 arc 간 각도가 30도인 경우에는 콜리메이터 직경과 관계없이 TAD가 증가할수록 감소하는 양상을 보였으나, 45도의 arc 간 각도에서는 400도의 TAD까지는 감소하다가 400도 이상의 TAD에서 $V_{50}$은 증가하거나 변화가 없었다. 적분 생물학적 유효선량 값의 변화는 arc 간 간격이 30도인 경우에는 콜리메이터의 직경에 관계없이 TAD가 증가함에 따라 미소하게 감소하는 양상을 보였다. arc 간 각도가 45도인 경우에는 콜리메이터 직경이 40 mm 이하에서는 TAD가 증가함에 따라 적분 생물학적 유효선량은 계속 감소하였으나, 50 mm와 60 mm 직경의 콜리메이터에서는 TAD가 400도까지는 감소하다가 500도 이상의 TAD에서는 증가하였다. 결론 : 정위방사선치료 시 400도 정도의 TAD를 사용하는 것은 300도 이하 혹은 500도 이상의 TAD를 사용하는 것 보다 치료 효과를 높이면서 치료계획과 치료 시 장비 및 인적 자원의 효율적인 운용을 기대할 수 있을 것으로 판단된다.

• 전기학회논문지
• /
• 제61권10호
• /
• pp.1554-1560
• /
• 2012

In this paper, the even harmonic current(2nd, 4th, 6th, 8th) of the arc fault current and normal current were measured in computer load and analyzed. The BPF with GIC was developed to detection of harmonic, the exact center frequency and a high degree of sharpness could be easily obtained. The total even harmonic distortion due to series arc fault in computer load was 31.2%, this value was increased 3.9 times better than the total even harmonic distortion of normal current. The results of analysis of arc fault current RMS variation rate and Peak variation rate per half-cycle, The RMS average variation rate are as follows ; the 2nd harmonic was 0.24, the 4th harmonic was 0.15, the 6th harmonic was 0.19, the 8th harmonic was 0.25, respectively. The Peak average variation rate are as follows ; the 2nd harmonic was 0.19, the 4th harmonic was 0.12, the 6th harmonic was 0.13, the 8th harmonic was 0.15, respectively. The results of this analysis utilize data to detect of series arc fault on wiring of computer load.

• 연구논문집
• /
• 통권30호
• /
• pp.147-157
• /
• 2000

The filtered vacuum arc source (FVAS), which is adopted by magnetic filtering methode to remove the macro-particle in vacuum arc plasma, was composed of a torus structure with bending angle of 60 degree. The radius of torus was 266 mm, the radius of plasma duct was 80 mm and the total length was 600 mm. The magnet parts were consisted of one permanent magnet, one magnetic yoke and five solenoid magnets. The plasma duct was electrically isolated from the ground so that a bias voltage could be applied. The baffles inside plasma duct were installed in order to prevent the recoil effect of macro-particles. Graphite was used as the cathode material to coat the amorphic diamond film and its diameter was 80 mm. The amorphic diamond film attracts much attention due to its excellent mechanical, optical and tribological properties suitable for wide range of applications. The effects of solenoid magnet in plasma extraction were studied by computer simulation and experiment using Taguchi's method. The source and extraction magnet affected the arc stabilization. The extraction beam current was maximized with low value of the source magnet current and high value of the filtering magnet current. Optimum deposition condition was obtained when the currents of arc discharge, source, extraction, bending, deflection and outlet magnet were 30 A, 1 A, 3 A, 5 A, and 5 A, respectively.

• International Journal of CAD/CAM
• /
• 제6권1호
• /
• pp.59-64
• /
• 2006

A new method to obtain explicit re-parameterization that preserves the curve degree and parametric domain is presented in this paper. The re-parameterization brings a curve very close to the arc length parameterization under $L_2$ norm but with less segmentation. The re-parameterization functions we used are $C^1$ continuous piecewise rational linear functions, which provide more flexibility and can be easily identified by solving a quadratic equation. Based on the outstanding performance of Mobius transformation on modifying pieces with monotonic parametric speed, we first create a partition of the original curve, in which the parametric speed of each segment is of monotonic variation. The values of new parameters corresponding to the subdivision points are specified a priori as the ratio of its cumulative arc length and its total arc length. $C^1$ continuity conditions are imposed to each segment, thus, with respect to the new parameters, the objective function is linear and admits a closed-form optimization. Illustrative examples are also given to assess the performance of our new method.

• 한국식품영양학회지
• /
• 제9권2호
• /
• pp.143-150
• /
• 1996

The studies was carried out to investigate ripening degree and functional properties of EMC produced with pancreatic protease and palatase ML. During production of EMC, the amounts of free amino acid and free fatty acid were increased with increasing the reaction time. The amount of total nitrogen(T-N) and water soluble nitrogen(WSN) were increased with increasing time. EMC had contents of 1.79eA T-N and 0.52o WSN at 60 min of hydrolysis time. SRI and FRI value had also a similar correlationship. On the gel filtration, 2 kinds of soluble proteining capacity was also shown in alkali solution. Furthermore the foaming stability had the same result as that of the solubility. The water absorption of EMC showed the highest level at pH 4.0 and 5.0.

• 한국진공학회지
• /
• 제10권4호
• /
• pp.431-439
• /
• 2001

비정질 다이아몬드 박막(amorphous-Diamond a-B)을 증착하기 위하여 제작된 Filtered Vacuum Arc Source (FVAS)는 60도의 굽힘 각도를 가지는 토러스형 구조로 토러스 반경 266 mm, 플라즈마 덕트 반경 80 % 전체 길이 600 mm이며, 1 개의 영구자석 및 5 개의 전자석으로 되어있다. 플라즈마 덕트는 임의의 전압을 인가할 수 있도록 전기적으로 절연 시켰으며, 덕트 내부는 배플을 설치하여 macro-particle의 되튐 현상을 방지하였다. 사용된 음극은 직경 80 mm의 graphite이다. 각 전자석이 플라즈마 인출에 미치는 영향은 taguchi 실험계획법을 이용, 수치 모사와 실험을 행하였다. 소스 전자석과 인출 전자석은 아크의 안정성에 영향을 주었고, 빔 인출 전류는 낮은 소스 전자석 전류와 특정한 필터 전자석 전류에서 최대값을 나타내었다. 이때 소스, 인출, 굽힘, 반사, 출구 전자석의 전류값은 1 A, 3 A, 5 A, 5 A, 5 A였으며, 아크 전류 30 A일 때, 빔 전류 밀도 3.2 mA/$\textrm{cm}^2$, 평균 증착률 5 $\AA$/sec를 얻었다. 또한 플라즈마 덕트의 바이어스 전압 증가에 따라, 빔 전류 밀도는 증가하였으며, 더 효율적인 빔을 인출할 수 있었다.

• 대한치과보철학회지
• /
• 제47권4호
• /
• pp.416-423
• /
• 2009

연구목적: 이번 연구의 목적은 PLV 수복물의 접착 시 사용되는 광중합형 레진 시멘트의 중합도를 Fronrier transform infrared spectroscope로 측정하여 도재의 두께, 광원 및 광조사 시간에 따른 중합도의 차이를 비교하기 위함이다. 연구재료 및 방법: 대조군으로는 1.0 mm의 투명한 slide glass를 사용하였고, 도재 시편은 IPS Empress Esthetic shade ETC1을 선택하여 0.5, 1.0, 1.5 mm의 두께로 제작하였다. 레진 시멘트는 광중합형 레진 시멘트인 Rely $X^{TM}$ Veneer Shade A3를 사용하였다. 광원으로는 Quartz Tungsten Halogen (QTH), Light Emitting Diode (LED), Plasma arc curing (PAC) 광중합기를 사용하였다. 레진 시멘트의 중합도는 FT-IR과 OMNIC 프로그램을 이용하여 측정하였다. 통계분석은 one-way ANOVA와 Tukey HSD를 이용하였다 ($\alpha$=0.05). 결과: 대조군에서 QTH와 LED로 광중합을 시행하였을 때 PAC로 광조사를 시행한 경우보다 중합도가 높았다. QTH와 LED로 광조사를 시행한 경우, 대조군과 0.5 mm, 1.0 mm, 1.5 mm의 도재 두께에서 유의차를 보이지 않았다. 반면, PAC로 광조사를 시행한 결과, 도재의 두께가 1.5 mm인 실험군의 중합도가 대조군과 0.5 mm에서 보다 통계적으로 유의하게 낮은 결과를 보인다 (P<.05). 두께가 1.0 mm의 도재와 LED 광중합기로 광조사하여 중합도를 비교한 결과, 20초간 광조사를 시행하였을 때와 비교하여 80초와 160초간 광조사를 시행한 경우 통계적으로 유의하게 중합도의 평균값이 높았다 (P<.05). 결론: 이번 연구의 한계 내에서, 도재의 두께가 0.5-1.5 mm 이내의 PLV 접착 시, PAC 중합기의 사용은 고려되지 않으며, QTH나 LED로 40초 이상 중합한다면 광중합형 레진 시멘트를 사용할 수 있다. 또한, 광중합형 레진 시멘트를 LED로 중합시킬 경우, 광조사 시간의 증가가 중합도의 증가와 비례하지 않으며, 일정시간 이상의 광조사가 중합도에 큰 영향을 끼치지 않는다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.1017-1020
• /
• 2002

The pure Ti is taken annealing process for one hour at 90$0^{\circ}C$. The pure Ti is sufficient for ASTM B348 Grade2. The rolling mill roll the Ti-8Ta-3Nb(wt%) which became vacuum melting in arc furnace until the length is about 45mm and the thickness is about 6.05mm. Then it is made 6mm$\times$6mm$\times$44mm by wire cutting with EDM and it is made ∮ 6mm by rough cutting with the general purpose lathe. The machining accuracy of implant parts in the dental and medical science are decided by dimension, shpe, straightness, surface roughness. It is difficult to cut for the Ti alloy. It is caused problems of straight degree and surface roughness to the Ti alloy have many cases which length is smaller than diameter in cutting. Total 24 specimens different kind of 4 alloies are used in experiment to gain a cutting property. According to the cutting velocity, cutting depth, cutting temperature, feed and clearance angle experiments are performed. Conclusively it is expected that cutting depth of 0.5mm, feed velocity of 0.07mm/rev and cutting velocity of 80m/min could make a suitable result.

• 대한기계학회논문집A
• /
• 제27권8호
• /
• pp.1418-1425
• /
• 2003

In CAD systems, a surface to be machined is expressed by a series of curves, such as B-spline, Bezier and NURBS curves, which compose the surface and then in CAM systems the curves are divided into a large number of line or arc segments. These divided movement commands, however, cause many problems including their excessive size of NC data that makes almost impossible local adjustment or modification of the surface. To cope with those problems, the necessity of real-time curve or surface interpolators was embossed. This paper presents an efficient real-time tool-path generation method fur interpolation of NURBS surfaces in CNC machining. The proposed tool-path generation method is based on an improved iso-scallop strategy and can provide better precision than the existing methods. The proposed method is designed such that tool-path planning is easily managed in real-time. It proposed a new algorithm for regulation of a scallop height, which can efficiently generate tool-paths and can save machining time compared with the existing method. Through computer simulations, the performance of the proposed method is analyzed and compared with the existing method in terms of federate, total machining time and a degree of constraint on the scallop height.

• 대한치과교정학회지
• /
• 제19권1호
• /
• pp.187-200
• /
• 1989

The purpose of this study was to find out the craniofacial skeletal characteristics and to establish standards in facial patterns of Korean adolescences with normal occlusion. The subjects consisted of 54 males and 71 females ranging in age from 12 to 16 years. To classify facial patrons, number the clinical deviations from the normal five key measurements: the facial axis, facial angle, mandibular plane angle, lower face height, mandibular arc, are added and averaged with the proper sign to divide subjects into three groups ; brachyfacial, mesofacial dolichofacial groups. For the comparison of each group, a total of 43 morphologic variables were employed and the data were analyzed by statistical methods. The findings of this study can be summerized as follows; 1. The mesofacial group was $54.4\%$, the brachyfacial group was $29.6\%$ and the dolichofacial group was $16.0\%$ in this subjects. 2. There were no significant differences in size and shape of cranial base among each groups. 3. The brachyfacial group manifested the forward positioned maxilla and mandible to anterior cranial base, smaller cant of the mandibular plane, square shaped mandible, and prominent symphysis as compared with dolichofacial group. 4. There were no significant differences in the cant of the maxilla to the anterior cranial base among each groups. 5. Ramal height and madibular body length of brachyfacial group were larger than those of dolichofacial group. 6. Brachyfacial group indicated the smallest degree in divergency of maxilla and mandible while dolichofacial group showed the largest degree.