• 한국해양공학회지
• /
• 제10권1호
• /
• pp.53-64
• /
• 1996

In this paper, rotating bending fatigue tests have been carried out to investigate the growth behabiors of surface fatigue crack initiated from a small artificial surface defect, that might exist in real structures, on 2024-T3 and 6:4 brass. The test results are analysed in the viewpoints of both strength of materials and fracture mechanics, it can be concluded as follows. The effect of a small artificial surface defect upon the fatigue strength is very large. The sensitivity of 2024-T3 on the defect is higher than that of 6:4 brass. The growth behavior of the surface fatigue crack of 2024-T3 is different from that of 6:4 brass. The growth rate of the surface fatigue crack of 2024-T3 is considerably rapid in the early stage of the fatigue life and apt to decrease in the later stage. It was impossible to establish a unifying approach in the analysis of crack growth begabior of 2024-T3 and 6:4 brass using the maximum stress intensity factor because of their dependence on stress level. But if the elastic strain and cyclic total strain intensity factor range were applied to obtain the growth rate of surface fatigue cracks of the materials, the data were found to be nearly coincided.

• 대한기계학회논문집
• /
• 제11권2호
• /
• pp.191-197
• /
• 1987

본 논문에서는 이상과 같이 그 중요성이 인정되는 작은 표면피로균열의 성장 특성을 조사하기 위하여 연강과 중탄소강에 두 종류의 작은 표면결함을 가공한 네가지 종류의 시험편을 제작하고, 응력비 R=-1인 소야식 회전굽힘 피로시험을 통하여 작은 표면결함이 피로강도에 미치는 영향과 그 성장특성을 조사한 후 응력확대계수 K를 사 용하는 방법과 반복전스트레인 확대계수범위 .DELTA. $K_{\epsilon}$t/를 비교 검토하여 그 유효성 을 조사하고 이를 파괴역학적 측면에서 고찰하였다.다.

• 한국전산구조공학회논문집
• /
• 제23권2호
• /
• pp.191-198
• /
• 2010

이 연구에서는 접착패치보강의 서로 다른 형태 즉, 패치와 접착제의 재료, 크기, 두께 뿐만 아니라 일면보강 또는 양면보강에 따른 일변균열판의 응력감소에 대한 연구가 수행되었다. 수치해석 도구로는 p-수렴 부분층별 모델이 사용되었다. 이 모델의 면내 변위는 구간별 연속인 선형변화로 가정하였고, 두께방향으로의 면외 변위는 일정한 상수로 가정하여 적용하였다. 변위장의 정의는 적분형 르장드르 다항식을 적용하였고, 수치적분은 별도의 외삽법 없이 각 층별의 절점에서 발생하는 적분값을 바로 얻을 수 있는 가우스-로바토 적분법을 사용 하였다. 또, 에너지 방출률법을 사용하여 응력확대계수를 산출하였다. 수치예제를 통해 제안된 모델의 정확도는 물론이고 접착패치 보강형태에 따라 변화되는 무차원 응력확대계수와 처짐의 항으로 응력감소 효과를 분석하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.389-394
• /
• 2001

The notched Charpy and Izod impact tests arc the most prevalent techniques used to characterize the effects of high impulse loads on ploymeric materials. An analysis method for rubber toughened PVC is suggested to evaluate critical strain energy release rates(Gc) from the Charpy impact energy measurements. An Instrumented Charpy impact tester was used to extract ancillary information concerning fracture properties in addition to total fracture properties and maximum critical loads. The stress intensity factor Kd was computed for varying amounts of rubber contents from the obtained maximum critical loads and also toughening effects were investigated as well.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.837-840
• /
• 2002

An analysis method for rubber toughened PVC is suggested to evaluate critical dynamic strain energy release rates($G_c$) from the Charpy impact energy measurements. An instrumented Charpy impact tester was used to extract ancillary information concerning fracture parameters in addition to total fracture energies and maximum critical loads. The dynamic stress intensity factor $K_{Id}$ was computed for varying amounts of rubber contents from the obtained maximum critical loads and also toughening effects were investigated as well. The fracture surfaces produced under low velocity impact fur PVC/MBS composites were investigated by SEM. The results show that MBS rubber is very effective reinforcement material for toughening PVC.C.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2004년도 춘계학술대회
• /
• pp.219-231
• /
• 2004

The Charpy and Izod impact tests are the most prevalent techniques used to characterize the effects of high impulse loads on polymeric materials. An analysis method for rubber toughened PVC is suggested to evaluated critical dynamic strain energy release rates(G$_c$) from the Charpy impact tester was used to extract ancillary information concerning fracture parameters in additional to total fracture energies and maximum critical loads. The dynamic stress intensity factor KID was computed for varying amounts of rubber contents from the obtain maximum critical loads and also toughening effects were investigated as well. The fracture surfaces produced under low velocity impact for PVC/MBS composites were investigated by SEM. The results show that MBS rubber is very effective reinforcement material for toughening PVC.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2001년도 춘계학술대회
• /
• pp.311-317
• /
• 2001

The notched Charpy and Izod impact tests are the most prevalent techniques used to characterize the effects of high impulse loads on ploymeric materials. An analysis method for rubber toughened PVC is suggested to evaluate critical strain energy release rates(Gc) from the Charpy impact energy measurements. An Instrumented Charpy Impact tester was used to extract ancillary information concerning fracture properties in addition to total fracture properties and maximum critical loads. The stress intensity factor Kd was computed for varying amounts of rubber contents from the obtained maximum critical loads and also toughening effects were investigated as well.

• 대한기계학회논문집A
• /
• 제26권8호
• /
• pp.1520-1526
• /
• 2002

The Charpy and Izod impact tests are the most prevalent techniques used to characterize the effects of high impulse loads on ploymeric materials. An analysis method for rubber toughened PVC is suggested to evaluate critical dynamic strain energy release rates(G$\_$c/) from the Charpy impact energy measurements. An instrumented Charpy impact tester was used to extract ancillary information concerning fracture parameters in addition to total fracture energies and maximum critical loads. The dynamic stress intensity factor Kid was computed for varying amounts of rubber contents from the obtained maximum critical loads and also toughening effects were investigated as well.

• 한국해양공학회지
• /
• 제3권2호
• /
• pp.617-617
• /
• 1989

This paper deals with a fatigue life prediction of a surface crack based on the experimentally obtained relationship between surface crack length ratio $a/a_{f}$ and cycle ratio $N/N_{f}$ using micro computer. Firstly $a/a_{f}$-$N/N_{f}$ curves obtained from experimental tests, were assumed as three curves UC(the upper limit curve), LC(the lower limit curve) and MC(the middle curve), and these were utilized to predict the fatigue life. Comparing the calculated values which represent the characteristics of crack growth behaviors from the three assumed curves with the experimental ones, it has been found that in the stable crack growth region, they coincide reasonably well each other. And the differences between the fatigue lives obtained from the assumed curves and the experimental fatigue life did not exceed 20%. Using the characteristics of $a/a_{f}$-$N/N_{f}$ curves, it is possible to predict the da/dN-Kmax curves and the S-$N_{f}$ curves.

• 한국해양공학회지
• /
• 제3권2호
• /
• pp.108-117
• /
• 1989

This paper deals with a fatigue life prediction of a surface crack based on the experimentally obtained relationship between surface crack length ratio $a/a_{f}$ and cycle ratio $N/N_{f}$ using micro computer. Firstly $a/a_{f}$-$N/N_{f}$ curves obtained from experimental tests, were assumed as three curves UC(the upper limit curve), LC(the lower limit curve) and MC(the middle curve), and these were utilized to predict the fatigue life. Comparing the calculated values which represent the characteristics of crack growth behaviors from the three assumed curves with the experimental ones, it has been found that in the stable crack growth region, they coincide reasonably well each other. And the differences between the fatigue lives obtained from the assumed curves and the experimental fatigue life did not exceed 20%. Using the characteristics of $a/a_{f}$-$N/N_{f}$ curves, it is possible to predict the da/dN-Kmax curves and the S-$N_{f}$ curves.