• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2005년도 연구개발 발표회 논문집
• /
• pp.318-323
• /
• 2005

To evaluate the accurate performance of turbomachinery, it is important to measure the unsteady flow phenomena downstream of the rotor blade. This paper presents the development of the fast-response total pressure probe for the measurement of the total pressure field at the exit of rotor and the result of measurement in a 1-stage axial turbine. The fast-response total pressure probe was fabricated by installing a fast-response pressure sensor near the head of a Kiel probe. And it measured the phase-lock averaged total pressure downstream of an 1-stage axial turbine. The developed probe successfully measured the accurate total pressure distribution at rotor exit and made possible to evaluate the loss distribution and the accurate performance of turbomachinery.

• 대한기계학회논문집
• /
• 제12권3호
• /
• pp.582-589
• /
• 1988

본 연구에서는 작동유체로서 습공기를 사용하였을때 수반되는 응축에 의한 전 압손실을 실험과 수치해석을 통하여 정체점에 있어서의 습공기의 온도, 과포화도 및 노즐 팽창율의 효과와 액적 질량비 (g)과의 관계로서 구명하였다.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2000년도 유체기계 연구개발 발표회 논문집
• /
• pp.226-235
• /
• 2000

Two representative finite volume methods, i.e., the time marching method and the pressure correction method, were applied to 8 centrifugal compressor impeller flows, with low to very high level of pressure ratio, among which 7 impellers' experimental performance is given in the open literature. The present study is focused on the prediction differences from both methods, developed by the authors, in the pressure correction method's point of view. In all cases, the time marching method gives a satifactory solution, but the pressure correction method does not. Up to about $18\%$ less level of total-to-total pressure ratio is predicted by the pressure correction method as the level of the impeller pressure ratio increases up to about 10. The drop of total pressure ratio is caused by the underestimation of static pressure rise which seems to be attributed to inappropriate linearization and discretization of the pressure/density coupling terms in the pressure correction equation.

• Journal of Mechanical Science and Technology
• /
• 제14권4호
• /
• pp.456-465
• /
• 2000

An experiment was conducted to investigate the aerodynamic losses of high pressure steam turbine nozzle (526A) subjected to a large range of incident angles ($-34^{\circ}\;to\;26^{\circ}$) and exit Mach numbers (0.6 and 1.15). Measurements included downstream Pitot probe traverses, upstream total pressure, and end wall static pressures. Flow visualization techniques such as shadowgraph and color oil flow visualization were performed to complement the measured data. When the exit Mach number for nozzles increased from 0.9 to 1.1 the total pressure loss coefficient increased by a factor of 7 as compared to the total pressure losses measured at subsonic conditions ($M_2<0.9$). For the range of incidence tested, the effect of flow incidence on the total pressure losses is less pronounced. Based on the shadowgraphs taken during the experiment, it' s believed that the large increase in losses at transonic conditions is due to strong shock/ boundary layer interaction that may lead to flow separation on the blade suction surface.

• 한국진공학회지
• /
• 제10권1호
• /
• pp.9-15
• /
• 2001

질량분석기가 장착된 초고진공챔버를 사용하여 미소체적을 갖는 평판표시소자용 패널내부에 존재하는 잔류가스의 전체압력과 분압을 성공적으로 측정하였다. 패널내부의 전체압력은 $10^{-6}$Torr범위로 측정되었으며, 전체압력의 증가에 크게 기여하는 가스분압은 아르곤, 메탄 및 헬륨 분압들이었다. 패널의 진공패키징을 위한 배기공정시 가열온도는 고진공패키징에 있어서 매우 중요하며, 가열배기 온도가 높을수록 전체압력과 메탄분압은 감소하였다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1987년도 한국자동제어학술회의논문집; 한국과학기술대학, 충남; 16-17 Oct. 1987
• /
• pp.541-546
• /
• 1987

An experimental study has been conducted to investigate the suction performance of a designed inlet. Total pressure distortion in the inlet S-duct was measured and the effect of lip thickness and throat area was analyzed. The volume flow rate of air into the turbojet engine was controlled to observe the effect of engine RPM to the total pressure distortion. The pressure data from 36 air tubes were obtained using scanivalve, pressure transducer, and visicoder system.

• 한국초전도ㆍ저온공학회논문지
• /
• 제8권3호
• /
• pp.5-8
• /
• 2006

The effect of annealing time in Metal Organic Deposition(MOD) method was investigated at reduced total pressure. As the total annealing pressure was reduced, the growth rate of YBCO films increased from 0.14nm/sec at atmospheric pressure to 4.2nm/sec at 1 Torr. For the total pres sure of 700, 500, 300, 100, and 1 Torr, the optimal annealing times of 60, 40, 20, 10, 2minutes were found in our experimental conditions. When the an nealing time was short, poor crystallinity or un-reacted phase was obtained. Also, the degradation of YBCO films occurred when exposed longer to the humid ambient at the high annealing temperature. The reduced pressure was found effective to in crease the growth rate and to control the pore size of the YBCO films in MOD method. A fast growth of MOD-YBCO films was realized with high critical current density over $1MA/cm^2$ using reduced pressure annealing. Large pores, usually observed at atmospheric pressure in MOD method, disappeared and also, the number of pores was reduced.

• 대한물리치료과학회지
• /
• 제11권4호
• /
• pp.29-37
• /
• 2004

Measurements of plantar pressure provide an indication of foot and ankle function during gait and other functional activities because the foot and ankle provide necessary support and flexibility for weight bearing and weight shifting while people are performing these activities. Plantar pressure is being increasingly used in both research and clinical practice to measure the effects of various footwear and physical therapy intervention. The influence of walking speed and ground inclination on plantar pressure parameters However has not been evaluated in detail. So, in this study to determine the effect of changes in walking speed and ground inclination on plantar pressure treadmills with different walking speeds and inclination were used. Plantar pressure parameters were measured with the Parotec system using the walking and running in 20 healthy participants(10 male, 10 female) aged $20{\sim}28$(mean 22.22, S.D.2.26 years) when slow walking and running. The result of this study with increased die walking speed, the peak pressure of 1st, 5th metatarsal head and total contact time and impulse total at the forefoot was affected by walking speed; however, die peak pressure, contact time and impulse total at the forefoot was not affected by ground inclination.

• 수산해양기술연구
• /
• 제28권2호
• /
• pp.157-163
• /
• 1992

In this paper, the relationship between static pressure recovery and turbulent energy was presented in case of swirling flows into a conical diffuser. The distributions of turbulent energy in a diffuser sectional area were measured by a hot wire anemometer. The following conclusion can be drawn from the experiment. Diffuser loss is constituted by a dynamic pressure loss and total pressure loss. The static pressure recovery depends strongly on the total pressure loss. The static pressure recovery depends strongly on the total pressure loss, and the turbulent energy varies inversely as the static pressure recovery coefficient.

• International Journal of Fluid Machinery and Systems
• /
• 제2권1호
• /
• pp.1-12
• /
• 2009

Surrogate modeling is applied to a compressor blade shape optimization to modify its stacking line and thickness to enhance adiabatic efficiency and total pressure ratio. Six design variables are defined by parametric curves and three objectives; efficiency, total pressure and a combined objective of efficiency and total pressure are considered to enhance the performance of compressor blade. Latin hypercube sampling of design of experiments is used to generate 55 designs within design space constituted by the lower and upper limits of variables. Optimum designs are found by formulating a PRESS (predicted error sum of squares) based averaging (PBA) surrogate model with the help of a gradient based optimization algorithm. The optimum designs using the current variables show that, to optimize the performance of turbomachinery blade, the adiabatic efficiency objective is improved substantially while total pressure ratio objective is increased a very small amount. The multi-objective optimization shows that the efficiency can be increased with the less compensation of total pressure reduction or both objectives can be increased simultaneously.