• 국제초고층학회논문집
• /
• 제6권3호
• /
• pp.249-259
• /
• 2017

The use of high-strength steels in construction of highrise and mega building structures can bring about many technological advantages from fabrication to erection. However, key design criteria such as local and lateral stability in current steel design specifications were developed based on tests of ordinary steels which have stress-strain characteristics very different from that of high strength steels. A series of tests on 800 MPa tensile strength steel (HSA800) members are summarized in this paper which were conducted to investigate the appropriateness of extrapolating current ordinary-steel based design criteria to high strength steels. 800 MPa I-shape beam specimens designed according to flange local buckling (FLB) criteria of the AISC Specification developed a sufficient strength for elastic design and a marginal rotation capacity for plastic design. It is shown that, without introducing distinct and significant yield plateau to the stress-strain property of high-strength steel, it is inherently difficult to achieve a high rotation capacity even if all the current stability limits are met. 800 MPa I-shape beam specimens with both low and high warping rigidity exhibited sufficient lateral torsional buckling (LTB) strength. HSA800 short-column specimens with various edge restraint exhibited sufficient local buckling strength under uniform compression and generally outperformed ordinary steel specimens. The experimental P-M strength was much higher than the AISC nominal P-M strength. The measured residual stresses indicated that the impact of residual stress on inelastic buckling of high-strength steel is less. Cyclic seismic test results showed that HSA800 members have the potential to be used as non-ductile members or members with limited ductility demand in seismic load resisting systems. Finally, recent applications of 800 MPa high strength steel to highrise and mega building structures in Korea are briefly presented.

• 한국산학기술학회논문지
• /
• 제16권9호
• /
• pp.6385-6390
• /
• 2015

수평 곡선 I-형 거더에는 초기곡률이라는 기하학적 특성으로 인해 휨 모멘트와 더불어 비틀림 모멘트가 작용하게 된다. 이러한 휨 비틀림 거동은 서로 상호 작용을 일으켜 약축방향으로 2차 휨거동을 유발하게 된다. 휨과 비틀림 간의 상호 작용은 곡선 거더를 조기에 비선형 상태 및 소성 상태로 유도하여 내하력의 저하를 야기하게 되고, 차량의 이동 위치에 따른 편심 하중은 비틀림을 더욱 증대시킬 수 있다. 그러나 기존에 연구되어왔던 직선 거더에 대한 휨 비틀림 상호관계식은 곡선 거더가 가지고 있는 거동 특성이 고려되지 않았기 때문에 수직하중을 받는 수평 곡선 I-형 거더의 극한 강도가 과대평가 될 수 있다. 따라서 이에 대한 보다 명확하고 합리적인 제안식의 적용이 곡선 거더의 설계 시에 필요하다. 본 연구에서는 유한요소해석을 통하여 편심하중이 작용하는 수평 곡선 I형 거더의 휨 비틀림 상호작용 특성을 파악하고 거동분석을 수행하였다.

• 한국산학기술학회논문지
• /
• 제15권4호
• /
• pp.2399-2405
• /
• 2014

조립식지그재그 형태의 단일거더시스템이 적용되는 경골형 교량은 비틀림에 취약한 구조이다. 특히 거더와 PHC(Pretensioned spun High strength Concrete) 말뚝의 고정 연결부는 비틀림 하중에 의한 과도한 응력이 집중되는 취약부이므로 이를 저감시키기 위한 방안이 요구된다. 본 연구에서는 연결부에 발생하는 과도한 응력을 저감시키기 위한 다양한 보강재 형식의 효율성을 수치해석적으로 평가하였다.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2002년도 가을 학술발표회 논문집
• /
• pp.3-10
• /
• 2002

Recently, arches are used structurally because of their high in-plane stiffness and strength, which result from their ability to transmit most of the applied loading by axial forces actions, so that the bending actions are reduced. On the other hand, the resistances of arches to (out-of-plane,) flexural-torsional behavior depend on the rigidities EI/sub y/, for lateral bending, GJ for Uniform torsion, and EI/sub w/ for warping torsion which are related to axial stress for flexural-torsional behavior. The resistance of an arch to out-of-plane behavior may be reduced by its in-plane curvature, and so it may require significant lateral bracing. Thus. it is supposed that In-plane preloading which cause an axial stress, have an effect on out-of-plane free vibration behavior of arches. Because axial stresses caused increase or decrease out-of-plane stiffness. But study about this substance is insufficient. In this thesis, We will study an effect of preloading on lateral free vibration of arches, using finite element method based on Kang and Yoo's curved beam theory (about curved beam element have 7 degree of freedom including warping) with FORTRAN programming.

• 한국안전학회지
• /
• 제24권4호
• /
• pp.74-81
• /
• 2009

In this study, the seismic performance of RC school buildings which were not designed according to earthquake-resistance design code were evaluated by using response spectrum and push-over analyses. The torsional amplification effect due to plan irregularity is considered and then the efficiency of seismic retrofitting methods such as RC shear wall, steel frame, RC frame and PC wing wall was investigated. The analysis result indicate that the inter-story drift concentrated in the first floor and most plastic hinge forms at the column of the first story. Among the retrofitting methods, the PC wing wall has the highest seismic performance in strength and story drift aspect. Especially, it can make building ductile behavior due to the concentrated inter-story drift at the first column hinge is distributed overall stories. The axial force, shear force and moment magnitude of existing elements significantly decreased after retrofitting. However, the axial and shear force of the elements connected to the additional retrofitting elements increased, and especially the boundary columns at the end of the retrofitting shear wall should be reinforced for assuring the enhancement of seismic performance.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.427-430
• /
• 2008

The influence of subsequent annealing treatment on the dynamic deformation and the fracture behavior of submicrocrystalline Al-4.4%Mg alloy is investigated in this study. After inducing an effective strain of 8 via equal-channel angular pressing at $200^{\circ}C$, most of the grains are considerably reduced to nearly equiaxed grains of $0.3{\mu}m$ in size. With an increment of various subsequent heat treatments for 1 hour, resultant microstructures are found to be fairly stable at temperatures up to $200^{\circ}C$, suggesting that static recovery will be dominantly operative, whereas grain growth is pronounced above $250^{\circ}C$. The results of tensile tests show that yield and ultimate tensile strength decrease, but elongation-to-failure and strain hardening rate increase with an increase in annealing temperatures. The dynamic deformation and the fracture behavior retrieved with a series of torsional tests are explored with respect to annealed microstructures. Such mechanical response is analyzed in relation to resultant microstructure and fracture mode.

• Structural Engineering and Mechanics
• /
• 제3권1호
• /
• pp.91-103
• /
• 1995

An analysis to determine shear centers for anisotropic elastic thin-walled composite beams, cantilevered and loaded transversely at the free end is presented. The shear center is formulated based on familiar strength of material procedures analogous to those for isotropic beams. These procedures call for a balancing of torsional moments on the cross sectional surface and lead to a condition of zero resultant torsional couple. As a consequence, due the presence of anisotropic coupling, certain non-classical effects are manifested and are illustrated in two example problems. The most distinguishing result is that twisting may occur for composite beams even if shear forces are applied at the shear center. The derived shear center locations do not depend on any specific anisotropic bending theories per se, but only on the values of bending and shear stresses which such theories produce.

• 콘크리트학회논문집
• /
• 제16권6호
• /
• pp.733-740
• /
• 2004

본 논문에서는 휨과 비틀림을 함께 받는 전형적인 건축분야의 프리캐스트 프리스트레스트 콘크리트 역T형 보와 직사각형 보의 거동을 연구하였다. 연구 목적을 위하여 국내 건축시장에서 사용되고 있는 주차장 활하중 $5 kN/m^2$ 및 상가 활하중 $12 kN/m^2$ 의 역T형 프리캐스트 프리스트레스트 콘크리트 보를 제작하였다. 또한 같은 길이의 보 밑면과 면적을 갖는 두개의 직사각형 콘크리트 보도 제작하였다. 따라서 설계 활하중과 단면형상이 다른 네 개의 보를 휭과 비틀림의 동시 작용 하에서 실험하여 그 결과를 분석하고 비교하였다. 실험결과 비틀림의 영향으로 시험체 모두 초기 균열 및 극한 휨의 강도가 저하되었다. 그러나 단면형상에 따라 사용하중 및 극한 하중 하에서의 하중 지지력에는 커다란 차이가 없는 것으로 나타났다.

• 한국강구조학회 논문집
• /
• 제20권1호
• /
• pp.1-8
• /
• 2008

강재 박스거더교의 바닥틀을 구성하며, 바닥판의 활하중과 고정하중을 지지하는 가로보와 세로보의 설계 합리화를 위한 연구가 수행되었다. 가로보는 일반 거더교의 수직 브레이싱 규정을 근거로 6m 이하의 간격으로 조밀하게 배치되며, 세로보는 가로보 사이에 배치된다. 또한 가로보와 세로보는 바닥판과 슬래브 앵커로 연결되지만, 허용응력은 횡비틀림좌굴의 발생을 고려하여 보수적으로 결정 된다. 강박스거더교의 경제성을 도모하고 가설 및 유지관리시의 편의성을 증진시키기 위하여 가로보의 간격을 10m로 증가시켜 세로보와 가로보 의 단면 및 이음부 설계에 대해 검토하였다. 세로보의 지간이 증가함에 따라 응력이 증가하여 고강도의 강재를 사용해야 하지만, 제작 및 유지관리면에서 세로보의 지간을 증가시키는 것이 바람직하며, 경제적으로도 유리할 것으로 판단된다. 바닥판과 세로보 및 가로보의 부착 강도를 충분히 확보하기 위해서는 기존에 사용되고 있는 슬래브 앵커 보다는 전단연결재를 활용하는 것이 바람직한 것으로 판단된다.

• 대한조선학회논문집
• /
• 제43권3호
• /
• pp.331-339
• /
• 2006

The objective of this paper is to calculate the fatigue strength for upper deck hatch corner insert plate of large container carriers without wave load analysis and global finite element analysis at the initial design stage. Wave load analysis and global F.E. analysis for three container carriers have been performed by GL(Germanischer Lloyd) procedure to propose the equation for hatch corner stress range which is the important factor in fatigue strength calculation. Considering the restraining effect of bulkhead, three types of equation, that is, single tight bulkhead, double tight bulkhead and support bulkhead have been proposed. Using the proposed equations, a simplified fatigue analysis based on GL rules has been performed for two container carriers of which fatigue strength analysis was carried out by GL. From the comparison between fatigue strength result of using the proposed equations and that of GL, it has been found that proposed stress range equations are useful for scantling of upper deck hatch corner insert plates for over 8,000 TEU class container carriers.