• Journal of the Korean Geotechnical Society
• /
• v.15 no.4
• /
• pp.3-17
• /
• 1999

Torsion shear tests under various stress paths were performed to study the behavior of sand during large stress reversal. The stress paths can be classified into the clockwise and the counterclockwise according to torque applied to specimen, and the directions of plastic strain incremental on the stress paths including large stress reversal are compared with the direction of stress state and stress incremental. From test results, the isotropic hardening theory using the principle of St. Venant desirably showed that direction of plastic strain incremental coincided with stress state on primary loading part and nearby failure point, but it might result in a rough approximation on part of unloading and reloading by stress reversal.

• Earthquakes and Structures
• /
• v.5 no.6
• /
• pp.703-731
• /
• 2013

In order to verify the applicability of buckling restrained braces (BRB's) and fiber reinforced polymer (FRP) sheets to the seismic strengthening of a low-rise RC building having the irregularities of a soft/weak story and torsion at the ground story, a series of earthquake simulation tests were conducted on a 1:5 scale RC building model before, and after, the strengthening, and these test results are compared and analyzed, to check the effectiveness of the strengthening. Based on the investigations, the following conclusions are made: (1) The BRB's revealed significant slips at the joint with the existing RC beam, up-lifts of columns from RC foundations and displacements due to the flexibility of foundations, and final failure due to the buckling and fracture of base joint angles. The lateral stiffness appeared to be, thereby, as low as one seventh of the intended value, which led to a large yield displacement and, therefore, the BRB's could not dissipate seismic input energy as desired within the range of anticipated displacements. (2) Although the strengthened model did not behave as desired, great enhancement in earthquake resistance was achieved through an approximate 50% increase in the lateral resistance of the wall, due to the axial constraint by the peripheral BRB frames. Finally, (3) whereas in the original model, base torsion was resisted by both the inner core walls and the peripheral frames, the strengthened model resisted most of the base torsion with the peripheral frames, after yielding of the inner core walls, and represented dual values of torsion stiffness, depending on the yielding of core walls.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.9
• /
• pp.979-984
• /
• 2012

An antiroll-bar assembly is a precision component that is designed to control the rolling of railway cars. It is important for ensuring a safe and comfortable ride. A torsion bar is the main part of the antiroll-bar assembly. Now, this part is classified as a consumable, and it is imported into Korea from France. Therefore, there is a strong need to domestically develop a torsion bar suitable for Korean conditions and to reduce cost and improve quality. In this study, an antiroll bar is developed, and it is analyzed and tested by using a road histogram measured on Korean railroads. This bar shows satisfactory results in a comparison with the imported bar. It has a novel design featuring a ring cover made of SUS steels to prevent the corrosion of the torsion bar. Its safety is examined through CAE analysis and wear tests. It is found that its design does not result in a significant difference in static and fatigue safety. Two different SUS steels were investigated in terms of their wear resistance, and the best one was adopted.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.10
• /
• pp.1339-1344
• /
• 2010

MSM (Modal Superposition Method) is a technique for analyzing structural durability by taking the vibration characteristics into consideration. In this paper, MSR (Modal Stress Recovery) method, which is similar to MSM, was reviewed to check its validity as a durability analysis method. The MSR method directly calculates the modal displacement time history in multibody dynamics analysis; as a result, the total analysis time is shorter than that of MSM method. We conduct durability analysis using the MSR method and a durability test of a torsion beam axle that is affected by various road loads within the natural frequency of the beam axle. The analysis results for critical location and durability were in good agreement with the respective test results. Therefore, durability analysis using the MSR method is effective in predicting the durability of the structures of various dynamic systems.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.5 no.3
• /
• pp.89-97
• /
• 2002

In this study, the effect of $\alpha$-phase morphology on the dynamic deformation behavior at ultra high strain rate was investigated by EBW(Explosive Bridge Wire) test. All of tests and analyses were conducted on three typical microstructures of Ti-6Al-4V alloy, i.e. equiaxed, widmanstatten and bimodal microstructures. The spall strength and HEL(Hugoniot Elastic Limit) of the specimens that have the thickness of 2mm and 4mm were highest with the bimodal microstructure. These results were similar with previous study which was performed by dynamic torsion test(Kolsky torsion test).

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.5 no.2
• /
• pp.39-51
• /
• 2001

This paper shows how boundary element method can be used to calculate torsion geometrical stiffness of cross-sections of various beams and airfoil profiles. Using the BEM direct formulation, the technique for determining bending and torsional geometrical characteristics of arbitrary multiply connected cross-sections is presented. The application limits of several well-known formulae on some test problems have been demonstrated and discused.

• Journal of Korean Society of Steel Construction
• /
• v.18 no.5
• /
• pp.543-551
• /
• 2006

Cold-formed steel studs that are being used as load-bearing members of wall panels for steel houses have a problem with their insulation due to the heat bridging of their web. Some additional thermal insulating materials should be used. To solve this problem, the new-concept hybrid stud, which consists of a galvanized steel sheet (t = 1.0 m - 12.0 m) and a GFRP panel (t = 4.0-6.0 mm), has recently been developed. An investigation on the structural behavior and the strength capacity of this new hybrid stud has been conducted so that it can be used in load-bearing wall panels of residential buildings. This paper describes the axial compression-torsion test results of the hybrid studs under both axial compression and torsion using ATTM. The main factors of the test were the stud length, the magnitude of the initial compressive force, and the loading method of the monotonic or cyclic loading. The torsion was applied increasingly while the initial compression was kept constant to the failure of the hybrid section. The advanced analysis results obtained form the finite element procedure that considered the material properties of the high-strength galvanized steel and the GFRP were compared with the test results for verification.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.6
• /
• pp.484-491
• /
• 2016

The purpose of this development is weight reduction of hollow type steel torque bar by changing the material from steel to composite. Structure analysis is executed by the finite element model generated by the structural load condition and geometric structure requirement. According to this analysis result, optimized ply sequence and wall thickness are defined. To simulate analysis result, torsion test for composite torque bar was performed. Throughout the test result, the stiffness and strength requirement of composite torque bar was verified.

• Proceedings of the KSR Conference
• /
• 2004.06a
• /
• pp.903-908
• /
• 2004

Among welded structure bogies in use for high speed freight car, a part of bogies manufactured in 1999 and 2000 have found problems that crack occurs in its end beam. In case of a freight car the difference of weight between empty and loading conditions are worse than in case of a passenger car. Moreover its brake system is tread brake without second suspension system. Cracks of end beam is supposed to be due to loading by brake system rather than vertical loading by freight. These cracks can make brake system useless and may be a cause of derailment in the worst case. In this study, we have proposed a simple torsion-free brake shoe holder hanger to remove torsion of hanger bracket which was supposed to be one of causes of cracks and performed finite element analyses. Also static load test was applied in torsion free brake shoe holder.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.3
• /
• pp.86-91
• /
• 2012

Door effort was calculated for a new door checker with torsion bar spring and integrated checker case by FE analysis. A hybrid checker arm which has peaks and valleys only on the upper surface was adopted to reduce noise in operation and make operation with more distinctive steps. The checker arm was modeled using shell elements to estimate both the longitudinal and the lateral resistance force by checker arm. By combining the checker arm resistance force obtained from analysis and the door self-closing force by the theoretical calculation, door effort was predicted to show the good correlation with test results. In addition the unrolling effect of roller model was investigated and a new roller type for more smooth rolling was studied.