• Composites Research
• /
• v.21 no.1
• /
• pp.40-45
• /
• 2008

Rubber hose assembly for automotive hydraulic brake during operation is subject to combined stresses of cyclic pressure, cyclic bending and torsion as well as thermal load. The rubber hose is composed of ethylene-propylene diene monomer(EPDM) rubber layers reinforced by polyvinyl acetate(PVA) braided fabrics. A durability tester with loading rigs for inducing the above cyclic stresses was used to investigate failure mechanisms in the rubber hose assembly. Failure examination was performed at every 100 thousands cycles of bending and torsion. Hose samples were sectioned with a diamond-wheel cutter and then polished. The polished surface was observed by optical microscope and scanning electron microscope (SEM). Some interfacial delamination with a length of about 1mm along the interface between EPDM rubber and PVA fabrics was shown at the test cycles of 400,000. The delamination induced some cracking into the outer rubber skin layer to leading the final rupture of the hose.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.1
• /
• pp.64-70
• /
• 2023

In this study, reliability tests of torsion control expansion anchors according to drill bit diameters were performed. The standard deviation and coefficient of variation of the anchor were reviewed through the tests for each variable, and the results were compared and evaluated with the standard test results. As a result of the reliability test of the M12 and M16 anchors with 1.04 times the drill bit diameter, they were within 20% of the ultimate tensile load permissible standard coefficient of variation. It was found that the pulling-out performance of the anchor installed in the large hole was sufficiently secured. However, it was found to be about 253% and 210% of the design strength, indicating that the pulling performance of the anchor installed in 1.04 times the drill bit diameter was sufficiently secured. As a result of the reliability test of the M12 and M16 anchors with 1.02 times the drill bit diameter, the value of the coefficient of variation of the ultimate tensile load limit was within 20%, which satisfies the test standard. It was shown to be about 136% and 168% of the design strength, indicating that the pulling-out performance of the anchor installed in 1.02 times the drill bit diameter is sufficiently secured.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.619-622
• /
• 2005

Purpose of this study is to investigate the size-dependent mechanical properties in micron scale medium. Theories such as the couple stress theory and strain gradient theory explain that the deformation in the micron scale is dependent upon the size of the medium. Specimens of the cantilever type, bridge type and paddle type beam that have thickness of 900, 1000 and 1200 nm and width of 10, 20, 30 and $50{\mu}m$ were fabricated by the MEMS technique. We carried out the bending and torsion test to measure the mechanical properties such as the young's modulus, yield strength and torsional rigidity using the AFM(Atomic Force Microscopy).

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.3
• /
• pp.110-115
• /
• 2010

This paper studies the vibration characteristics of a vehicle seat on several driving conditions. Modal test for a vehicle seat is conducted for the three different boundary conditions: on the rigid jig, BIW and the full vehicle. In driving on various road conditions and speeds, vibration level is measured at several locations including seat mounting and seat-back. The vibration pattern for each driving condition is found where the suspension mode and the 1st bending and torsion modes of the seat make the major contribution on it.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.83-83
• /
• 2009

The automotive chassis components are structural assemblies that support the engine, suspension, and steering components of the vehicle. For the development of AHSS components, the durability analysis is important. In this paper, the low cycle fatigue property of AHSS was evaluated for the geometry complex and local plasticity in the base material. The GMAW optimization was implemented for the weld soundness using the moving least square method. And the weld S-N curves of AHSS were evaluated to access durability analysis for the weld region. For the verification, the durability analysis of the couple torsion beam axle (CTBA) was performed and compared to the rig test result. The durability analysis using the low cycle fatigue property and the evaluated weld S-N curve of AHSS met the good agreement with the test result.

• Steel and Composite Structures
• /
• v.20 no.1
• /
• pp.43-56
• /
• 2016

Polyurethane foam with low density used in sandwich panels is examined in the paper. A series of experiments was carried out to identify mechanical parameters of the foam. Various experimental methods were used for determining the shear modulus, namely a four and three point bending tests (the most common in engineering practice), a double-lap shear test and a torsion test. The behavior of PU in axial compression and tension was also studied. The experiments revealed pronounced anisotropy of the PU foam. An orthotropic model is proposed. Limitations of application of isotropic model of PU in engineering practice is also discussed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.298-299
• /
• 2005

Differently from the tensile, transverse compression and torsion cases, the bending test of HTS tapes requires a lot of time and efforts, since the sample should be mounted successively onto bent sample holders in the order of decreasing radius and measuring the $I_c$ at each step. The influence of repeated cooling and warming experienced during these processes on the $I_c$ degradation can not be ignored. As a result, in this study, particularly. a new one-body type sample holder which provides continuous bending strains at 77K was devised. And, $I_c$ degradation behavior of Bi-2223 tapes under easy bending condition was investigated and compared that with other cases using Goldacker-type bending tester or respective sample holder.

• The korean journal of orthodontics
• /
• v.33 no.2 s.97
• /
• pp.131-140
• /
• 2003

The purpose of this study was to evaluate clinical applications of electroplating method through investigation of the physical properties of orthodontic rectangular wires according to varying their cross section. For the study, it was accomplished to electroplate the 0.016-inched orthodontic rectangular stainless steel wire. The cross section of stainless steel orthodontic rectangular wire increased from $0.016{\times}0.016inch\;to\;0.017{times}0.017inch$ by electroplating. The wire was heat treated to improve an adhesion between the wire and electroplated metal. h three-point bending test and torsion test were conducted in order to compare physical properties among three wire groups; $0.016{\times}0.016wires(group 016),\; electroplated\;0.016{\times}0.016wires(group\;016P)\;and\;0.017{\times}0.017$ wires (group 017). Through the investigations of each wire group, following results were obtained 1. At three-point bending test, the group Ol6P showed higher tendency in the degree of stiffness, yield strength and ultimate tensile strength than the group 016. Stiffness and ultimate tensile strength showed statistically significant differences between two groups at three-point bending test (p<0.05). 2. Stiffness, yield strength, and ultimate tensile strength of the group 016P showed lower tendency than those of the group 017 Stiffness showed statistically significant differences between two groups at three-point bending test (p<0.05). 3. Torque/twist rate, yield torsional moment, and ultimate torsional moment of the group 016P showed higher tendency than those of the group 016. All measurements showed statistically significant differences between two groups alter torsion test (p<0.05). 4. Torque/twist rate, yield torsional moment, and ultimate torsional moment of the group 0166P showed lower tendency than those of the group 017. Yield torsional moment, and ultimate torsional moment showed statistically significant differences between two groups after torsion test (p<0.05).

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2182-2186
• /
• 2003

This paper presents the differential type resonant accelerometer (DRXL) and its performance test results. The DRXL is the INS grade, surface micro-machined sensor. The proposed DRXL device produces a differential digital output upon an applied acceleration, and the principle is a gap-dependent electrical stiffness variation of the electrostatic resonator with torsion beam structures. Using this new operating concept, we designed, fabricated and tested the proposed device. The final device was fabricated by using the wafer level vacuum packaging process. To test the performance of the DRXL, a nonlinear self-oscillation loop is designed using describing function technique. The oscillation loop is implemented using discrete electronic elements. The performance test of the DRXL shows that the sensitivity of the accelerometer is 12 Hz/g and its long term bias stability is about $2mg(1{\sigma})$. The turn on repeatability, bandwidth, and dynamic range are 4.38 mg, 100 Hz, and ${\pm}\;70g$, respectively.

• Journal of the korean Society of Automotive Engineers
• /
• v.3 no.1
• /
• pp.32-37
• /
• 1981

모든 차형을 간단한 이상형으로 가정하여 그들을 수치적인 값으로 비교할 수 있다면 승용차 차 체의 설계상 매우 큰 도움이 될 것이다. 실제로 새로운 모델의 차가 개발되었을 때에는 다음과 같은 이유 때문에 그 prototype body에 대한 정적 시험이 실시되고 있다. 1) 조기에 설계의 문제점이나 차체의 주결함을 발견할 수 있어 시간과 경비를 절약할 수 있다. 2) 계속적인 정적 시험을 통하여 구조적으로 만족할 만한 road car를 만들 수 있다. 3) 과설계를 방지하여 차체의 경량화에 기여하고, 최적설계의 개발을 위한 길을 제시해 준다. 차체에 대한 정적 시험은 위와 같은 이유 때문에 발전되어 왔으며, 정적 시험의 효과를 ㅊ대로 하기 위하여 그것은 순수한 공학적 원리에 기초를 두어 실제의 사용조건과 충분히 일치되는 시 험으로서 고안되었다. 차체구조는 그 사명의 다양성뿐만 아니라 제작, 개수에 상당한 노력과 시 간이 필요하기 때문에 조기에 문제점을 발견하여 결함을 제지하지 않으면 안된다. 구조체로서의 많은 필요조건 중에서 특히 중요시되는 것은 강도, 강성 및 내구성이다. 그 때문에 차체의 강도, 강성시험은 이론적인 해석(탄성학, 구조역학, 강도학 등)에 앞서 여러가지 방법이 개발되어 왔 으며, 여기에서는 그 중 가장 대표적인 방법인 비틀림시험(torsion test)과 굽힘시험(bending test) 에 관하여 Pony 4-door Sedan 차체의 시험 결과를 토대로 하여 기술하고자 한다.