• 대한치과교정학회지
• /
• 제21권3호
• /
• pp.495-500
• /
• 1991

To design the acceptable prejusted bracket for Korean using straight wire appliance, teeth and dental arch of Korean were studied and brackets were made. It was named Oriental Bracket. The results were following. 1. The bracket position for Korean occlusion was obtained. 2. The axial inclinations of each tooth were obtained. 3. The crown torques of each tooth were obtained. 4. The thickness of each tooth was obtained. 5. The bracket (Oriental bracket) was made according to these data.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 A
• /
• pp.290-292
• /
• 1998

The driving torque acting on a rotatable disk of watthour meter is proportional to the effective power. The aim of this paper is to show how the driving torque on a disk can be measured by a LVDT transducer. This driving torque is obtained by the theoretical computation. To verify the computated result, the LVDT as torque transducer, was used. A comparison is made between computed and measured torques.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2017년도 임시총회 및 하계학술연구발표회
• /
• pp.229-229
• /
• 2017

• 연구논문집
• /
• 통권22호
• /
• pp.21-26
• /
• 1992

Dynamic analysis is important in structural design of SCARA or articulated type industrial robots and is' usually done to main three axes. In this paper, robot arm dynamics was analyzed using FBD(free body diagram). Though the proposed scheme becomes complex as DOF(degree of freedom)increases, it allows to see types and directions of forces and moments acting on the body. Therefore, the strength analysis of robot arm can be done relatively easy in a case of either closed or open loop chain. This method can be used for obtaining dynamic simulation at off-line programming system and calculating required torques at joints at on-line system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.21-23
• /
• 2001

A design and analysis program is proposed for switched reluctance motor using an analytical method and a CAD program LabVIEW. The algorithm uses conventional permeance method, in which flux linkages, inductances and torques are calculated numerically. In order to analyze a dynamic characteristics of the motor, voltage control scheme is fallen and a single pulse operation is applied. 2 SRM models are analyzed under the given specifications and constraints. The results compared with measured data.

• Structural Engineering and Mechanics
• /
• 제73권1호
• /
• pp.75-82
• /
• 2020

In this study, the problem of torsion of bars with open cross section surrounded by corrugated boundaries is analyzed. An approximate analytical solution is given using perturbation technique. First, the stress analysis for circular open cross-section for arbitrary opening angle is formulated and the problem is analytically solved. Second, the open cross-section with corrugated cross section is analyzed using perturbation method. First order contributions to the stresses and the torques have been added. The results have been exemplified and compared by considering special examples.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2016년도 임시총회 및 하계학술연구발표회
• /
• pp.71-72
• /
• 2016

• 충청수학회지
• /
• 제24권2호
• /
• pp.313-317
• /
• 2011

In this article, we consider an unbounded minimal graph $M{\subset}R^3$ which is contained in a slab. Assume that ${\partial}M$ consists of two Jordan curves lying in parallel planes, which is symmetric with the reflection under a plane. If the asymptotic behavior of M is also symmetric in some sense, then we prove that the minimal graph is itself symmetric along the same plane.

• Journal of Korean Dental Science
• /
• 제11권1호
• /
• pp.14-20
• /
• 2018

Purpose: The purpose of this study is to measure and compare the removal torques of different cements applied in attachments of zirconia restorations on titanium (Ti) abutments fitted with retrievable cement-type slot (RCS) on the lingual side for the better retrievablity by use of a slot driver. Materials and Methods: Three types of cements were used in the experiment: two permanent cements in $RelyX^{TM}$ U200 (RU) (3M ESPE) which is a resin cement and $FujiCem^{TM}$ (FC) (GC) which is a resin-modified glass ionomer cement, and a temporary cement in $Freegenol^{TM}$ temporary cement (TC) (GC). Measurements of removal torques were conducted as follows; an attached sample was fixed on the equipment customized for the experiment; a slot driver was connected to a MGT12 (Mark-10 Corp.), a torque measurement instrument; the sample had the driver fitted to its RCS and then was rotated until the it was removed; and finally, the maximum torque value was recorded. Result: As for the removal torque measurement results, the average values were $47.9{\pm}2.6Ncm$ for RU, $43.4{\pm}1.5Ncm$ for FC, and $20.9{\pm}1.0Ncm$ for TC. The statistical analysis using Kruskal-Wallis test yielded the significance probability of P<0.05 (P=0.002), which confirmed the presence of significant differences between the three groups. Conclusion: All three cements exhibit clinically acceptable levels of removal torque when applied to an upper zirconia implant restoration fitted with a lingual slot, with RU and FC, the two permanent cements, having the significantly higher values than that of TC, the temporary cement.

• 패션비즈니스
• /
• 제11권4호
• /
• pp.204-220
• /
• 2007

The background of Korean Ethnical Costume was originated from those northern mounted nomadic groups, which was Scythe style Costume Culture. Through the antique records and paintings of tombs bequests hereby describe the forms of Scythian Cotume (1) Headgear : There was Conical Cap(or Pointed Cap), Feathered Cap, and Crown. (2) Clothes : Both Men and Women wore Jacket as upper garment with leftsided collars, narrow sleeves to the length of the hip line. As lower garment, they wore the tight Trousers and Kungo(:窮袴)that was attached with gusset. (3) Belts and Boots : On the upper garment bound the leather Belts that was hanged a hook that was shaped of animal form at the end. Scythian Buckles was divided into six groups, animal-shaped, animal's head shaped, animal fight-shaped, rectangle-shaped, rectangle openwork-shaped, genre scene shaped Buckle. To the Boots, they wore leather boots. (4) Ornaments : Ornaments divided into Dress Trimming(:Gold plaques), Earrings, Necklaces(;Torques), Bracelets, Rings. Scythian Gold Plaques were divided into several types according to the shape, animal style(curved beast shape, profile shape, head reversed over its back shape), round shape, quadrilateral form, star shape, flower shape, crescent shape, bundle shape, human appearance. Earrings consisted of a plain ring and pendant ring was a middle ornament hung from it to a pendants which hung was made of heart shaped leaves of the tree, beads-linked. Scythian Torques were divided into several types according to the shape, Torque with Terminal style, Spiral style, Layers style, Crescent-shaped pectoral style, Crown style. Scythian Bracelet were divided into 4 styles according to the shape, Bracelets with ends shaped like beasts style, Spiral style, Layers style, Crown with openwork style. Rings were rhomb-shaped and animal shaped styleRings (5) Animal motifs used in Scythian ornaments appears that in some cases the work was intended to be purely ornamental, while many times the motifs had symbolic meaning (such as the successful dominance of the aggressor over the victim portrayed in the attack scenes). Magical use of symbols may have been inten-ded to guarantee the power of the aggressor.