• 전력전자학회논문지
• /
• 제2권2호
• /
• pp.49-56
• /
• 1997

스위치드 리럭턴스 전동기(switched reluctance motor : 이하 SRM 이라 칭함)는 가변 인덕턴스 프로파일의 비선형성과 리플성분이 포함된 펄스전류에 구동되는 본질적인 특성 때문에 토오크는 맥동성분을 포함한다. 본 논문에서는 토오크의 맥동에 영향을 미치는 전류파형 형태를 고찰하고, 속도나 부하에 관계없이 어드밴스 각(advance angle)와 여자전압을 제어함으로써 토오크 맥동을 저감할 수 있는 단일 펄스모드 스위칭 제어방법을 제안하였다. 그리고 설계 제작된 6/4 SRM을 이용하여 제안한 스위칭 제어방법의 타당성을 실험적으로 확인하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.702_703
• /
• 2009

Electric Power Steering(EPS) system is superior to conventional Hydraulic Power Steering(HPS) system in aspect of fuel economy and environmental concerns. The EPS system consists of torque sensor, electric motor, ECU(Electric Control Unit), gears and etc. Among the elements, the torque sensor is one of the core technologies of which output signal is used for main input of EPS controller. Usually, the torque sensor has used torsion bar to transform torsion angle into torque. The torsion angle of both ends of a torsion bar is measured by a contact variable resistor. In this paper, the sensor is accurately analyzed using 3D finite element method and its characteristics with respect to four different shapes of the stator teeth are compared. The four shapes are rectangular, triangular, trapezoidal and circular type.

• 한국항공우주학회지
• /
• 제37권1호
• /
• pp.89-98
• /
• 2009

CMG는 3축으로 토크를 발생시키기 위해 클러스터로 구성하여 사용할 수 있다. CMG 클러스터에서 발생되는 여러 가지 설계에 고려되어야 할 문제들이 있다. 이러한 문제들을 지상에서 미리 검증하는 것이 필수적이다. 따라서 본 논문에서 토크센서로 위성자세를 계산하는 CMG 시뮬레이터를 제안하였다. 개발과정에서 발생한 김발각문제 해결을 위해 보정방법과 칼만필터가 제시되었다. 보정방법은 계산된 김발각을 기본으로 사용하고 센서 값을 보조로 사용해서 오차를 줄인다. 또한 개발된 CMG 시뮬레이터를 이용하여 특이점 회피를 위한 구동법칙과 자세제어 로직 시험결과도 예로서 제시되었다.

• 전기학회논문지
• /
• 제66권4호
• /
• pp.643-650
• /
• 2017

This pap4er analyzes resonance characteristics of a slave motor that is not controlled by load and parameter differences between Dual motors during parallel operation in middle-low speed. Dual SPMSMs(Surface mounted Permanent Magnet Synchronous Motor) connected in parallel to a single inverter controlled by the master and slave control in this paper. Based on the stability analysis of the SPMSM for a variation of torque angle, the 6th nonlinear state equation of the torque angle variation in the SIMM(Single Inverter Multi Motor) structure is derived according to a mathematical model for the dual motors. In general, an analysis of the 6th order nonlinear state equation is complex. Therefore, a resonance frequency generated from the slave motor is found from the characteristic equation of the 2nd order system obtained by linearization and model reduction near steady state operation point. Through simulations and experiments, it is confirmed that the stability analysis of the SPMSMs and state equation models are useful for the variation of the torque angle analyzed in this paper.

• 전기학회논문지
• /
• 제66권10호
• /
• pp.1481-1487
• /
• 2017

This paper proposes a sensorless speed control algorithm for parallel-connected dual Surface-mounted Permanent Magnet Synchronous Motors fed by a single inverter. For stable parallel operation of synchronous motors with a single inverter, each motor has to be constantly kept in the synchronization state regardless of load torque. If the master motor with the larger load is controlled, the synchronous state will be maintained. Therefore, detection of the master motor is essential. Conventionally, the master motor is determined by comparing the rotor position error from the relation between the back-EMF for torque angle and the flux position. consequently, the position sensor is deemed essential for finding the rotor position. In this paper, we proposed a method that decides the magnitude of the load from the power angle of two motors due to the load variation and selects the motor to control through the sign function for the sensorless speed control without the position sensor. The results of simulation and experiment conducted verify the efficacy of the proposed method.

• 전력전자학회논문지
• /
• 제3권3호
• /
• pp.263-272
• /
• 1998

본 논문은 자기적 비선형성과 상간의 토오크중첩을 고려하여 맥동토오크를 최소화시킬 수 있는 제어기법을 제시하고 이를 DSP를 이용하여 구현한 SRM의 구동시스템에 대하여 기술하였다. 이를 위해 먼저 몇 단계의 상전류 크기에 대한 회전자 위치별 인덕턴스값과 발생토오크의 크기를 실측한 후 이들 대표값으로부터 신경회로망을 사용하여 제어에 필요한 충분히 정밀한 값들을 추론한다. 또한 각 상간의 토오크중첩을 고려하여 총합 발생토오크의 맥동성분의 최소화되도록 상별 지령토오크 파형을 설정한다. 회전자위치와 상전류를 검출하고, 이 검출값과 추론된 토오크데이터를 이용하여 구한 토오크 값이 지령토오크를 추종하도록 델타변조기법에 의한 제어기를 구성한다. 이러한 제어방식을 실시간으로 처리하고, 제어기의 신뢰성을 높이기 위해 DSP를 사용하였다.

• 한국정밀공학회지
• /
• 제18권10호
• /
• pp.93-100
• /
• 2001

The analysis and control of a new type unsymmetrical slotted self-bearing step motor for small angle control is presented. The motor actuator is used for both motor and bearing functionality without any additional coil windings or electromagnets for bearing functionality. A circular-arc, straight-line permeance model for the fringing effect is presented. An unsymmetrical slotted self-bearing step motor layout and control algorithm are described. A new control current generation method using the electromagnets layout geometry, which needs no additional current for bearing functionality, is proposed. As the result of this analysis the fringing effect largely influences on the system characteristics. especially in torque. Even if the bearing functionality is added into the motor functionality, it is shown that the magnitude of torque is not changed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 A
• /
• pp.25-27
• /
• 1998

The switched reluctance motor(SRM) drive system provides a good adjustable speed and torque characteristics. However, it also has some drawbacks such as relatively high torque ripple and acoustic noise which are caused by the torque production mechanism. To reduce torque ripple and to have precise speed control, PLL technique is adopted. The PLL system in conjunction with dynamic dwell angle control scheme has good speed regulation characteristics. Digital control system with a 80c196kc micro-controller is used to be realized this drive system. Test results show that the suggested control system has the ability of dynamic and precise speed control.

• Journal of Electrical Engineering and Technology
• /
• 제10권3호
• /
• pp.1048-1057
• /
• 2015

This paper proposes a sensorless speed control algorithm for parallel-connected dual Surface-mounted Permanent Magnet Synchronous Motors (SPMSMs) fed by a single inverter. For stable parallel operation of synchronous motors with a single inverter, each motor has to be constantly kept in the synchronization state regardless of load torque. If the master motor with the larger load is controlled, the synchronous state will be maintained. Therefore, detection of the master motor is essential. Conventionally, the master motor is determined by comparing the rotor position error from the relation between the back-EMF for torque angle and the flux position; consequently, the position sensor is deemed essential for finding the rotor position. The parallel sensorless speed control method proposed in this paper uses no position sensor, instead it compares the flux-axis current from the connection between the back-EMF for torque angle and current in unbalanced load conditions. The results of simulation and experiment conducted verify the efficacy of the proposed method.

• 조명전기설비학회논문지
• /
• 제29권9호
• /
• pp.89-95
• /
• 2015

This paper presents a current sensorless maximum torque control of a synchronous reluctance motor drive. Stator current and current angle vs. maximum torque are obtained using measured d-axis and q-axis inductances. Then, d and q-axis stator voltage references for current sensorless maximum torque control are calculated from stator voltage equations. The proposed method is verified by simulation results comparing with conventional method.