• E2M - 전기 전자와 첨단 소재
• /
• 제7권2호
• /
• pp.145-151
• /
• 1994

The multi-dielectric layer SiOz/Si3N4/SiO2(ONO) is used to scale down the memory device. In this paper, the change of composition in ONO layer due to the process condition and the conduction mechanism are observed. The composition of the oxide film grown through the oxidation of nitride film is analyzed using auger electron spectroscopy(AES). AES results show that oxygen concentration increases at the interface between oxide and nitride layers as the thickness -of the top oxide layer increases. Results of I-V measurement show that the insulating properties improve as the thickness of the top oxide layer increases. But when the thickness of the nitride layer decreases below 63.angs, insulating peoperties of film 28.angs. of top oxide and film 35.angs. turn over showing that insulating property of film 28.angs. of top oxide is better than that of film 35.angs. of top oxide. This phenomenon of turn over is thought as the result of generation of surface state due to oxygen flow into nitride during oxidation process. As the thickness of the top oxide and nitride increases, the electrical breakdown field increases, but when the thickness of top oxide reaches 35.angs, the same phenomenon of turn over occurs. Optimum film thickness for scaled multi-layer dielectric of memory device SONOS is estimated to be 63.angs. of nitride layer and 28.angs. of top oxide layer. In this case, maximum electrical breakdown field and leakage current are 18.5[MV/cm] and $8{\times}{10^-12}$[A], respectively.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2018년도 춘계학술대회 논문집
• /
• pp.43.1-43.1
• /
• 2018

Spatial distribution of binding state in depth direction is investigated in a hard skin layer on soft polydimethylsiloxane (PDMS) fabricated by Ar ion beam irradiations. The hard skin layer known as a silica-like homogenous layer was composed of two layers. Impinging Ar ions transfer energy to PDMS as a function of collisional energy transfer rate, which is the maximum at surface and decreases gradually as an ion penetrates. This formed the heterogeneous hard skin layer that consists of a top-most layer and an intermediate layer. XPS depth profiling showed the existence of the top-most layer and intermediate layer. In the top-most layer, scission and cross-linking were occurred simultaneously and Si-O bond showed dissociated status, SiOx (x = 1.25 - 1.5). Under the top-most layer, there was the intermediate layer in which cross-linking is mainly occurred and Si-O bond showed silica-like binding status, SiOx (x = 1.75 - 2). And theoretical analysis which calculates the collisional energy transfer and a displacement per atom explained the thickness variation of top-most layer according to Ar ion energy from 360 eV to 840 eV.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2002년도 International Meeting on Information Display
• /
• pp.1081-1081
• /
• 2002

Top emission organic EL devices were fabricated by using metal-doped cathode interface layer to achieve low drive voltages. Also, facing-targets-type sputtering was used to sputter indium-tin oxide layer on top of organic active layer. The devices fabricated in this study showed reasonably high external quantum efficiency of about 1 % which is comparable to that of bottom-emission-type devices.

• Journal of Magnetics
• /
• 제10권3호
• /
• pp.99-102
• /
• 2005

Modification in exchange bias of a NiFe/FeMn/NiFe trilayer, on introduction of a nonmagnetic Al layer at the top FeMn/NiFe interface, is investigated in multilayers prepared by rf magnetron sputtering. The introduction of Al layer leads to vanishing of bias of the top NiFe layer. But the bias for the bottom NiFe layer increases steadily with increasing Al layer thickness and attains bias (230 Oe) which is greater than that of the trilayer without the Al layer (150 Oe). When the top NiFe layer thickness is varied, exchange bias has highest value at 12 nm thickness for 1 nm thicknes of Al layer. Ion beam etching of the top NiFe layer also leads to an enhancement in bias for the bottom NiFe layer.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.413-414
• /
• 2008

We have studied an organic layer thickness dependent optical properties and microcavity effects for top-emission organic light-emitting diodes. Manufactured top emission device, structure is Al(100nm)ITPD(xnm)/$Alq_3$(ynm)/LiF(0.5nm)/Al(23nm). While a thickness of hole-transport layer of TPD was varied from 35 to 65nm, an emissive layer thickness of $Alq_3$ was varied from 50 to 100nm for two devices. A ratio of those two layers was kept to about 2:3. Variation of the layer thickness changes a traverse time of injected carriers across the organic layer, so that it may affect on the chance of probability of exciton formation. View-angle dependent emission spectra were measured for the optical measurements. Top-emission devices show that the emission peak wavelength shifts to longer wavelength as the organic layer thickness increases. For instance, it shifts from 490 to 555nm in the thickness range that we used. View-angle dependent emission spectra show that the emission intensity decreases as the view-angle increases. The organic layer thickness-dependent emission spectra show that the full width at half maximum decreases as the organic layer thickness increases. Top emission devices show that the full width at half maximum changes from 90 to 35nm as the organic layer thickness increases. In top-emission device, the microcavity effect is more vivid as the organic layer thickness increases.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2011년도 춘계학술발표회 논문집
• /
• pp.251-263
• /
• 2011

This study was carried out in order to investigate the effect of pre-coating layer on top-coating layer. The coated paper with five different formulations were prepared. The properties of coated paper were measured and correlation between pre and top-coated layer was evaluated. Paper gloss was increased with addition of clay and GCC that has smaller particle size. Roughness was decreased with using smaller particle GCC, clay and talc. The highest thickness was obtained with talc. Brightness and whiteness of pre-coated layer were affected to top-coated layer. GCC 60 shows the highest and ununiform water adsorption during 1sec. The adsorption was higher with increasing coated weight. Talc shows the excellent water adsorption properties due to its wettability. These results indicate that final printability and properties of top coating layer can be controlled with adjusting pre-coating layer.

• Geomechanics and Engineering
• /
• 제16권1호
• /
• pp.49-58
• /
• 2018

Open-mode cracks could be commonly observed in layered rocks. A concept model is firstly used to explore the mechanism of the vertical cracks (VCs) in the top layer. Then the crack behaviour of the two-layer model is simulated based on a cohesive zone model (CZM) for layer interfaces and a plastic-damage model for rocks. The model indicates that the tensile stress normal to the VCs changes to compression if the crack spacing to layer thickness ratio is lower than a threshold. The results indicate that there is a threshold for interfacial shear strength that controls the crack patterns of the layered system. If the shear strength is lower than the threshold, the top layer is meshed by the VCs and interfacial cracks (ICs). When the shear strength is higher than the threshold, the top layer is meshed by the VCs and parallel cracks (PCs). If the shear strength is comparative to the threshold, a combining pattern of VCs, PCs and ICs for the top layer can be formed. The evolutions of stress distribution in the crack-bound block indicate that the ICs and PCs can reduce the load transferred for the substrate layer, and thus leads to a crack saturation state.

• 펄프종이기술
• /
• 제48권1호
• /
• pp.27-33
• /
• 2016

This study was carried out in order to investigate the effect of binder properties in pre-coating layer on the characteristics of top-coating layer and print mottle of coated paper. Four different latices were used as a binder in pre-coating layer, and coating color prepared with a same formulation was applied for top-coating. The properties and print mottle of coated paper were evaluated. It was found that glass transition temperature (Tg) was the important factor to control the properties of pre- and top-coating layer. PPS roughness of coated paper was decreased and paper gloss was increased with applying binder which has lower Tg. Properties of top-coating layer were affected by the binder used in pre-coating layer. Print mottle of coated paper was improved with using binder which has lower Tg in pre-coating layer. These results indicate that final printability and properties of top-coating layer can be improved with using suitable binder in pre-coating layer.

• Asian-Australasian Journal of Animal Sciences
• /
• 제13권11호
• /
• pp.1593-1597
• /
• 2000

In the quiescent state, cattle-manure slurry stratifies into three discernible layers, namely a floating scum layer, a bottom sludge layer and a watery middle layer. The proportions of top (scum), middle and bottom (sludge) layers were approximately 20, 60 and 20% respectively of the volume of the whole slurry. Particulate matter from the different stratified layers was characterised for particle size distribution and cellulose, hemicellulose and lignin composition. Total solids concentrations of top, middle and bottom layers were 12.7, 2.8 and 7.4% respectively. Larger particles were found in the top layer compared with the bottom. The top layer contained the highest amounts of Neutral Detergent Fibre (NDF), Acid Detergent Fibre (ADF), cellulose and hemicellulose, but the lowest amount of Total Kjeldahl Nitrogen (TKN). The bottom layer contained the highest amounts of Acid Detergent Lignin (ADL) and TKN. With increase in particle size, there were increases in NDF, ADF, cellulose and hemicellulose, accompanied by decreases in ADL and TKN. Biochemical methane potential of the three layers was also measured. The top layer was found to produce the most methane with the middle layer producing the least. Biomethanation rate from the top layer was also the highest. Differences in biomethanation rates and biochemical methane potential were attributed to differences in chemical composition of the particulate matter. About 48%, 23% and 30% of the total chemical oxygen demand (COD) in the top, middle and bottom layers respectively of the slurry was found to be degradable.

• 한국정보처리학회:학술대회논문집
• /
• 한국정보처리학회 2012년도 춘계학술발표대회
• /
• pp.1073-1074
• /
• 2012

최근 인터넷의 발달과 사용량의 증가로 데이터의 양이 급증함에 따라 대용량 데이터를 효율적으로 검색하는 top k 질의 처리가 중요시 되고 있다. Layer 기반 방법은 가장 잘 알려진 top k 질의처리 방법이며, 객체의 모든 속성의 값들을 이용하여 객체들을 layer들의 리스트로 구성하는 방법이다. 본 논문에서는 그 중에서 convex hull을 사용하여 layer list를 생성하는 기존 연구를 조사하고 문제점을 파악한다.