• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.3
• /
• pp.367-372
• /
• 2012

In nuclear plants, UVR (under voltage relay, 27r) of 1E bus, which protected and supplied power to essential loads, to safety trip of reactor and supplied to starting signal of EDG (emergency diesel generators) automatically. therefore UVR tolerances setting and calculation method has been important to nuclear facility. If calculation and tolerances values differ or ignore, may induced power loss and economical loss by protective failure. This paper show results for calculation methods, and whether dependant or independent methods for factors. included whether PT (potential transformer/voltage transformer) tolerance or not adapted, and based on UVR setting method within a difference minimum and maximum of rated voltage to safety operation in nuclear plants.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.875-877
• /
• 2003

This paper use fault location algorithm for single-phase-to-ground faults on the teed circuit of a parallel transmission line that use only local end voltage and current information. When Newton-Raphson iteration method is used, the Initial value may cause error or cause not suitable result. Suggested new calculation model uses NVP methodology, which is one of the fault tolerance technology to solve this problem. EMTP simulation result has shown effectiveness of the algorithm under various conditions.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2004.05a
• /
• pp.241-244
• /
• 2004

Dimension and tolerance are very important factors both in a design stage and in a manufacturing stage. As a part of process planning, the tolerance transfer aims at determining the method for converting design dimensions and tolerances into manufacturing dimensions and tolerances based on a given drawing. A procedure for the tolerance transfer is proposed in this paper. Tolerance chart is a valuable graphical tool for a process planner to determine the manufacturing dimensions and tolerances, and consisted of several steps. Among several steps necessary for making up the tolerance chart, the methods for the identification of dimension chain, the determination of tolerances, and the calculation of operational dimensions are presented by using concepts and new presentation methods. A solution method for each step is derived which will be used to establish the tolerance transfer techniques.

• Spatial Information Research
• /
• v.11 no.1
• /
• pp.23-32
• /
• 2003

TIN is applied in pondage calculation and topography analysis. And much processing time and storage capacity are needed because TIN contains information as elevation, slope and aspect. In the construction of TIN using contour, weed tolerance that is used for the simplification of line is influenced on the sampling distance of contour. The processing time and storage capacity of TIN are calculated in according to the weed tolerance of various size in this research. And we estimated OEMs standard error that is created from TIN to present reasonable weed tolerance and decided the size of weed tolerance that satisfy DEM standard error. We got TINs weed tolerance that satisfy DEM standard error(5m) was 70m and DEMs resolution is 20m as estimation result.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.12
• /
• pp.75-83
• /
• 2010

Every mechanical part for mass production has dimensions with tolerances in engineering drawing. Tolerance is given to guarantee assemble parts together satisfying functional requirements and dimensional constraints. Tolerance is essential factor for standardization of parts or assembly and has huge influence on manufacturing cost. It will be desirable to have tolerances as broad as possible for minimizing manufacturing cost. This paper describes tolerance analysis of u-joint assembly that is a part of automobile steering system. Within the range of tolerances of parts, accumulated effect is estimated by arithmetic calculation, probability theory and Monte carlo simulation. Each result is compared to investigate the method for increasing productivity.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.36 no.4
• /
• pp.135-142
• /
• 2020

The new method for evaluating the displacement tolerance of sky-bridges with pin-roller type supports was proposed considering both return period of phase difference between connected buildings and geometrical characteristics of skybridge. Because displacement tolerance is relative value, which is most affected by the phase difference of the connected buildings, the dynamic response of these building with time history analysis should be evaluated. However, the initial phase could not be specified, so the result of displacement tolerance would be varied with respect to initial value. Thus, the tolerance can be reasonably evaluated SRSS calculation with design displacements based on statistical approach and of each building. In addition, the geometrical characteristics of sky-bridge should be considered because the transverse displacement of sky-bridge span causes the shear deformation of the bridge and longitudinal displacement tolerance cannot release the shear deformation. Therefore, the some pin-end support in sky-bridge should have longitudinal displacement tolerance to accommodate the shear deformation. By resolving this shear deformation, it is possible not only to accommodate transverse displacement, but also to avoid the complicated joint details such as both pot bearing and guided supports with shear key.

• The Journal of the Acoustical Society of Korea
• /
• v.21 no.3
• /
• pp.221-229
• /
• 2002

In thin paper, error tolerance of each array element which satisfies error tolerance of beam pattern is decided by using the Monte-Carlo method. Conventional deterministic method decides the error tolerance of each element from the acceptance pattern by testing all cases, but this method is not suitable for the analysis of large number of array elements because the computation resources increase exponentially as the number of array elements increases. To alleviate this problem, we applied new algorithm which reduces the increment of calculation time increased by the number of the array elements. We have validates the determined error tolerance region through several simulation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.153-153
• /
• 2013

Turbomolecular pump (TMP) is widely used to obtain and maintain high vacuum by spinning turbine rotors to migrate gas molecules to the exhaust of the pump. However, performance of the TMP has not been well observed when it is influenced by strong magnetic field. Such study may give useful information about magnetic field tolerance of TMP, development of magnetic shielding technique for key components of TMP, etc. For this purpose, magnetic field induced by a circular current source was firstly designed and investigated. Using spherical coordinates and vector potential, magnetic field throughout the space including axis of rotation was calculated. Due to the rotational symmetry of the circular current source, induced magnetic field is azimuthally symmetric and, thus, is analyzed by radial and polar components of the magnetic fields. In order to enhance the numerical accuracy for the calculation, magnetic field was expressed by complete elliptic integrals of first and second kinds. According to the calculation, when 1 A of DC-current passes through a 1 turned circular wire with 50 cm of diameter, overall magnitude of the inducedmagnetic field was about 0.02 Gauss, which was used to the determination of the current and the number of turns of wires to fabricate the coil for the study on the magnetic field tolerance of TMP.

• Journal of the Optical Society of Korea
• /
• v.18 no.6
• /
• pp.720-731
• /
• 2014

There are many kinds of optical systems to widen a field of view. Fisheye lenses with view angles of 180 degrees and omni-directional systems with the view angles of 360 degrees are recognized as proper systems to widen a field of view. In this study, we proposed a new optical system to overcome drawbacks of conventional omni-directional systems such as a limited field of view in the central area and difficulties in manufacturing. Thus we can eliminate the undesirable reflection components of the omni-directional system and solve the primary drawback of the conventional system. Finally, tolerance analysis using Zernike polynomial coefficients was performed to confirm the productivity of the new optical system. Furthermore, we established a method of optical axis alignment and compensation schemes for the proposed optical system as a result of tolerance analysis. In a sensitivity calculation, we investigated performance degradation due to manufacturing error using Code V(R) macro function. Consequently, we suggested compensation schemes using a lens group decentering. This paper gives a good guidance for the optical design and tolerance analysis including the compensation method in the extremely wide angle system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.184-190
• /
• 2003

In this study, several methods for measuring floor impact sound were introduced. Among them, the simple methods (impedance method and diffuse index method) which can be easily applied to site works were investigated. Moreover, the comparison between the calculation results using diffuse index method and the experimental results measured in real apartment structures was conducted. Consequently, the modified diffuse index method, which can be practically used for predicting the performance of to the floor impact sound of apartment structures and can meet the allowable tolerance of Grade I (${\pm}$5㏈), was proposed.