• 한국세라믹학회지
• /
• 제33권1호
• /
• pp.41-48
• /
• 1996

Self-propagating High-temperature Synthesis of Ti+N system has been investigated using the cylindrical high pressure reactor. The nitrogen pressure was varied from 40 to 80 atmosphere and TiNx(x=0.55) powder produced by SHS process was used as a diluent in order to control the reaction. Both the velocity of surface reaction and the ratio of TiN synthesis increased with increasing the nitrogen pressure. As the amount of diluent increases the degree of conversion to titanium nitride increases. Homogenious TiN powder was obtained in the composition 50Ti+50TiN0.94(diluent)

• 한국표면공학회지
• /
• 제39권5호
• /
• pp.199-205
• /
• 2006

Titanium nitride (TiN) coatings were produced on AISI 420 stainless steel by DC magnetron sputtering of a Ti target changing the processing variables, such as the flow rate of $N_2/Ar$, substrate temperature and the existence of Ti interlayer between TiN coatings and substrates. The hardness and residual stress in the films were investigated using nanoindentation and a laser scanning device, respectively. The stoichiometry and surface morphology were investigated using X-Ray Diffraction and SEM. The corrosion property of the films was also studied using a polarization method in NaCl (0.9%) solution. Mechanical properties including hardness and residual stress were related to the ratio of $N_2/Ar$ flow rate. The corrosion resistance also was related to the processing variables.

• ETRI Journal
• /
• 제13권4호
• /
• pp.58-69
• /
• 1991

고집적회로에서 A1 금속공정의 diffusion barrier로 널리 사용되는 titanium nitride의 성질을 조사하였다. 실제 회로 구조의 열적 안정성을 관찰하기 위하여 준비된 TiN/Ti다층 barrier를 $600^{\circ}C$까지 열처리하여 x-ray photoelectron spectroscopy (XPS), cross-sectional transmission electron microscopy(XTEM) 등으로 분석하였다. 열처리 온도가 증가됨에 따라 oxygen은 TiN 층의 표면과 pure-Ti 층에 pile up 된다. TiN 층의 표면에서는 $600^{\circ}C$열처리시 TiN이 분해되어 완전히 $TiO_2$가 형성되며, TiN 층 내에서는 oxygen 함량은 열처리 온도의 증가에 따라 커지고 이때 형성되는 Ti-oxide는 $TiO_2$ 보다 TiO, $Ti_2$$O_3$ 상태로 존재하게 된다. Pure-Ti 층은 열처리시 두개의 층으로 나누어 지는 데, 표면에서 침투하는 oxygen과 pure-Ti이 반응하여 Ti-oxide 층이 생기며 실리콘 기판과의 반응으로 Ti-silicide를 형성한다. $600^{\circ}C$에서 모든 Ti 층이 반응으로 소모되고 열적 stress, Ti-silicide의 grain growth, oxygen의 침입으로 TiN 층에 blistering이 발생한다.

• 한국반도체및디스플레이장비학회:학술대회논문집
• /
• 한국반도체및디스플레이장비학회 2003년도 추계학술대회 발표 논문집
• /
• pp.1-6
• /
• 2003

Flow modulation chemical vapor deposition process has been reported as an alternative way to obtain low resistivity, low residual chlorine content and good step-coverage titanium nitride film. Flow and concentration characteristics in a vertical FMCVD reactor are analyzed by using computational fluid dynamics method. The results show that 1.0 second as Cl reduction period is too short and there is still $TiCl_4$ gas above the holder at the end of the period. Time variation of $TiCl_4$ gas concentration on the holder shows that at least 3.0 second is necessary as Cl reduction time for the sake of film characteristics.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2015년도 춘계학술대회 논문집
• /
• pp.68-68
• /
• 2015

질화 티타늄(titanium nitride; TiN)은 색상이 미려하고 물리적 특성이 우수한 특성에도 불구하고 내산화성이 낮아 이를 해결하기 위해서 TiN에 Al을 첨가한 TiAlN 소재가 개발되었다. 하지만 난삭재 가공용 공구의 사용 온도가 $800^{\circ}C$이상인 점을 고려하여 $800^{\circ}C$ 이상의 고온 환경에서도 산화가 일어나지 않는 고경도 박막 소재가 요구되고 있으며 TiAlN 소재에 Si을 첨가하면 내산화성이 향상된다는 연구결과가 보고되고 있다. 본 연구에서는 음극 아크 증착과 스퍼터링을 동시에 이용한 하이브리드 공정으로 제조한 TiAlSiN 박막의 Si 함량에 따른 미세구조, 물리적 특성 그리고 내산화성을 평가하였다.

• 한국표면공학회지
• /
• 제26권5호
• /
• pp.225-234
• /
• 1993

Titanium nitride coatings were deposited onto SUS304 stainless steel substrates pretreated by mechanical scrubbing, chemical etching at 50% HCl solution and Ar ion etching. Adhesion strength were measured by scratch tester and confirmed by SEM with EDS. Adhesion strength of Ar ion etched substrate was 10 to 15 times higher than that of mechanical scrubbed or chemical etched substrate. Ar ion etching brought about an uniform and fine spherical shaped surface, while chemical etching gave rise to a rough and irregular surface on SEM micrograph. It was suggested that higher adhesion strength might be caused by anchoring effect of Ar ion etched surface prior to TiN deposition.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.50-50
• /
• 2007

We report the effect of the film thickness on electrical properties of Ti(N) film resistors. The applications of titanium nitride thin film resistor in $\Pi$-type attenuators are also characterized. As film thickness decreases from 100 to 30 nm, temperature coefficient of resistance significantly decreases from -60 to -148 ppm/K, while sheet resistance increases from 37 to $270\;{\Omega}/{\square}$. The characterizations of 20dB-attenuators using thin film resistors are improved in comparison with those using thick film resistors. The $\Pi$-type attenuators using Ti(N) thin film resistors exhibit a attenuation of -19.94 dB and voltage standing wave ratio of 1.16 at a frequency of 2.7 GHz.

• 한국표면공학회지
• /
• 제25권3호
• /
• pp.133-143
• /
• 1992

Titanium nitride(TiN) films have been prepared by HCD plasma enhanced reactive ion plating. Density and temperature of the plasma generated by the HCD were investigated. It was shown that parameters such as the substrate bias voltage(0 350V) and N2 flow rate(10 180SCCM) influenced the growth, the growth, the microstructure and the color tone of the film mostly. In order to study the interface region, surface analysis by AES combined with sputter depth profiling was performed. Microhardness of the coated TiN films were measured by micro Vickers hardness tester. Also, the effect of coating parameters on composition, coating surface and fracture morphology, grain size and growth rate were examined.

• 구강회복응용과학지
• /
• 제32권3호
• /
• pp.194-201
• /
• 2016

목적: 본 연구는 Co-Cr, Ti-6Al-4V 합금에 Zirconium Nitride (이하 ZrN) 적용 시, 의치상 레진과의 접착력을 비교하는 것이다. 연구 재료 및 방법: Co-Cr, Ti-6Al-4V 디스크(직경 10 mm, 두께 2.5 mm)를 각각 14개씩 제작하였고, ZrN 코팅에 따라 2개의 그룹으로 나누었다. Primer로 시편 전처리 후, 의치상 레진(직경 6 mm, 두께 5 mm)을 부착하였다. 표면 측정기를 이용하여 시편의 거칠기를 측정한 후, 만능 시험기를 이용하여 전단결합강도를 측정하였으며, 이원분산분석으로 통계 분석하였다. 시편 표면과 파절 양상을 주사전자현미경을 이용하여 관찰하였다. 결과: ZrN을 코팅한 시편에서 유의하게 높은 표면 거칠기를 나타내었고(P < 0.05), 전단결합강도는 낮았다(P < 0.001). ZrN 코팅 시편에서는 혼합성 파절과 부착성 파절이 함께 나타났다. 결론: Co-Cr, Ti-6Al-4V 합금에서 ZrN 코팅 처리는 의치상 레진과의 결합력을 약화시켰다.

• 대한치과보철학회지
• /
• 제37권2호
• /
• pp.212-234
• /
• 1999

Dental restorative materials must have the physical properties to withstand wear and corrosion. Base metal alloys possess better mechanical properties and lower price than the gold alloys. For these reasons such alloys have largely replaced the precious metal alloys. One aspect to con-sider is the release of metal substances to oral environment. The release of elements from dental alloys is a continuing concern because the elements may have the potentially harmful biological effects on local tissues. The purpose of this study was to minimize metal release on the nonprecious metal surfaces by ion beam assisted deposition(IBAD) of titanium nitride (TiN) Ni-Cr-Be alloys with and without TiN coatings were secured in an wear test machine opposing ruby ball to determine their relative resistance to wear with loom, 200m, 300m and 400m sliding distance. And the corrosion behavior of the Ni-Cr-Be alloys with and without TiN coatings and 3 dental noble alloys have been studied. Potentiodynamic curves were used to analyse the corrosion characteristics of the alloys. The measurement of the released Ni and Cr ions was conducted by analysis of the electrolyte solution with atomic absorption spectroscopy. The results were as follows : 1. The critical sliding distance that wore down TiN coatings of $2.5{\mu}m$ thickness in this study condition was 300m. 2. Ion beam assisted deposition of TiN showed a good surface modification with respect to the properties of wear and corrosion resistance. 3. X-ray diffraction showed that the strongest peak of TiN is TiN(111) in the coatings. 4. The release of Ni and Cr ions from alloys measured by means of atomic absorption spectroscopy was reduced by ion beam assisted deposition of TiN.