• Elastomers and Composites
• /
• v.43 no.2
• /
• pp.72-81
• /
• 2008

Nowadays, modifying asphalt to improve the resistancy of plastic deformation or rutting on roads has been drawing attention. In this study, asphalts were modified with modifying agents and ground rubber from waste tire (GRT), and the effects of modifier and GRT on the properties of asphalt were analyzed. The Marshall stability of modified asphalt was increased by 98% and the tensile strength increased by 43% compared to straight asphalt. GRT played an important role in enhancing these properties. Viscosity tests, penetration tests and TMA analysis showed the deformation resistancy of modified asphalt. IR and GPC tests indicated that asphalt and modifier have similar chemical structures to each other, and chemical bonding between asphalt and modifier have occurred so that the molecular size lengthened.

• Journal of the Korea Concrete Institute
• /
• v.19 no.5
• /
• pp.623-630
• /
• 2007

Grouting materials are used for the unification of superstructural and substructural body like bridge seat (shoe) or machinery pedestal and e.t.c by filling their intercalary voids. Accordingly, grouting materials have been developed and used mainly with products of high strength because those materials are constructed specially in a part receiving large or impact load. In this situation, the structural body constructed by grouting materials with high stiffness-centered (caused by high strength) products is apt to cause brittle failure when receiving over a limit stress and to cause cracks according to cumulative fatigue by continuous and cyclic load. In addition, grouting materials are apt to cause cracks by using too much rapid hardening agents that give rise to high heat of hydration to maintain high strength at early age. In this study, to overcome these problems, cement type grouting materials including powder of waste tire and resin as elastic materials which aim to be more stable construction and to be improvement of mother-body's unification are developed and endowed with properties of high toughness and high durability add to existing properties of high flowability, non-shrinkage and high strength. Besides, this study contribute to of for green construction materials for being possible recycling industrial waste like waste tire and flyash. On the whole, seven type mixing conditions are tested and investigated to choose the best mixing condition.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.5
• /
• pp.822-827
• /
• 2002

In general, jerk phenomenon appeared because of gear changing, when a vehicle starts off or climbs an incline. Therefore, it makes ride quality worse. In this paper, an optimal pattern of automatic transmission was designed using fuzzy logic in order to improve ride quality. After del eloping fuzzy rule for shift pattern control of automatic transmission, dynamic characteristics (i.e. acceleration, velocity, distance and so on) were simulated using dynamic model of a car. To do this he powertrain model of a vehicle with automatic transmission including torque converter, gear box, and final gear drive - from engine to tire - is developed.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1191-1198
• /
• 2011

The railway business was began at England in 1767. Since then, it has been changed for configuration of rail over the years and made in the form of I. The train propulsion has been developed in a engine of steam, diesel, motor, electromagnetic force and a pneumatic engine, continuously. also, the friction has been improved in a steel-wheel, rubber tire, frictionless maglev system and railless system. In consequence, the efficiency and improvement speed for train have been accomplished. In this paper, it is investigated for the structure with lightweight using the change for supporting the form of lateral pressure by centrifugal force in the substructure supporting load for railway vehicles.

• International Journal of Automotive Technology
• /
• v.6 no.6
• /
• pp.625-633
• /
• 2005

Vehicle drift was reduced using statistical six sigma tools. The study was performed through four steps: M (measure), A (analyze), I (improve), and C (control). Step M measured the main factors which were derived from a fishbone diagram. The measurement system capabilities were analyzed and improved before measurement. Step A analyzed critical problems by examining the process capability and control chart derived from the measured values. Step I analyzed the influence of the main factors on vehicle drift using DOE (design of experiment) to derive the CTQ (critical to quality). The tire conicity and toe angle difference proved to be CTQ. This information enabled the manufacturing process related with the CTQ to be improved. The respective toe angle tolerance for the adjustment process was obtained using the Monte Carlo simulation. Step C verified and controlled the improved results through hypothesis testing and Monte Carlo simulation.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1126-1131
• /
• 2007

This paper presents unified chassis control (UCC) to improve the vehicle lateral stability. The unified chassis control implies combined control of active front steering (AFS), electronic stability control (ESC) and continuous damping control (CDC). A direct yaw moment controller based on a 2-D bicycle model is designed by using sliding mode control law. A direct roll moment controller based on a 2-D roll model is designed. The computed direct yaw moment and the direct roll moment are generated by AFS, ESP and CDC control modules respectively. A control authority of the AFS and the ESC is determined by tire slip angle. Computer simulation is conducted to evaluate the proposed integrated chassis controller by using the Matlab, simulink and the validated vehicle simulator. From the simulation results, it is shown that the proposed unified chassis control can provide with improved performance over the modular chassis control.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.191-194
• /
• 2006

Recently the quality improvement of the steel cord product is demanded by the tire market. After wire drawing process, produced residual stresses have a harmful effect on the durability of the wire and become the cause which decreases the quality of the product. Therefore, to improve the quality of the steel cord product, the research regarding the method of residual stress relaxation is necessary. To evaluate the quality of the drawn wire, it is important to measure the residual stress, because the residual stress decides a variety of the quality level which is demanded in the drawn wire. This study proposed a residual stress relaxation method in the drawn wire using FE analysis. The validity of the analysis results was verified by nanoindentation test.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.5
• /
• pp.79-84
• /
• 2011

Air pollutants from a small marine diesel engine are increasing and the IMO(International Marine Organization) regulation asked for its reduction. In this study, NOx reduction technologies such as improvement of various cooling systems are applied to the small marine diesel engine. The various cooling systems are a intercooler, a heat exchanger for engine coolant, and an exhaust manifold by water cooling. These systems are tested on an engine dynamometer and a exhaust gas analyzer by a marine diesel engine test regulation. Test results are shows that the small marine engine are satisfied the IMO NOx regulations; Tire II.

• Journal of Biosystems Engineering
• /
• v.25 no.2
• /
• pp.79-88
• /
• 2000

Effects on tractive performance of design parameters of cage wheel as a traction aid to driving tires of tractor in wet paddy field were investigated experimentally. an experimental cage wheel was designed so that the design parameters such as wheel diameter, wheel width, lug pitch and lug angle could be varied during traction test, The traction test was conducted in two different types of wet paddy field ; shallow and deep harpan fields . Experimental results showed that tractive performance is affected by both soil conditions and the design parameters. A considerable improvement on the tractive performance was obtained by using a cage wheel with 45$^{\circ}$ lug angle in shallow hardpan and smaller lug pitch in deep hardpan. The diameter of cage wheel was mostly influential to the tractive performance both in shallow and deep hardpans.

• Elastomers and Composites
• /
• v.50 no.3
• /
• pp.159-166
• /
• 2015

Silica which is used for reinforcing filler in tire industry is widely known as eco-friendly material exerting $CO_2$ reduction effect through decrease of rolling resistance and improvement of wet grip. Generally silica is classified as a highly polar filler because it contains a large number of silanol (Si-OH) group on its surface. And also silica gives a lower reinforcing effect than carbon black due to its poorer rubber-filler interaction. Therefore silica is treated with silane coupling agent or activator, then following the conventional rubber blend method, vulcanized sheets were prepared using a hot press, and cure characteristics, mechanical properties and abrasion resistance of the test specimens were investigated. It was found that with an increase in the silane coupling agent content the tensile strength, 300% modulus and abrasion resistance increased while Mooney viscosity decreased and crosslink density slightly increased with an increase of activator.