• IEMEK Journal of Embedded Systems and Applications
• /
• v.2 no.2
• /
• pp.76-81
• /
• 2007

A novel multi-layer type micro gas sensor for $NO_X$ detection was designed and fabricated. Micro platform defined as type II-1 in this article for micro gas sensor was fabricated using the MEMS technology to meet the demanding needs of lower power consumption. Nano composite materials were fabricated with nanosized tin oxide powder and $\underline{m}$ulti-$\underline{w}$all $\underline{c}$arbon $\underline{n}$ano $\underline{t}$ube (MWCNT) to improve sensitivity. We investigated characteristics of fabricated multi-layer type micro gas sensor with $NO_2$ concentration variations at constant 2.2 V. Sensitivity (S) of micro gas sensor were observed to increase from 2.9, to 7.4 and 11.2 as concentrations of $NO_2$ gases increased from 2.4 ppm, to 3.6 ppm and 4.9 ppm. When 2.4 ppm of $NO_2$ gas was applied, response time and recovery time of micro gas sensor were recorded as 101 seconds and 142 seconds, respectively.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.217-218
• /
• 2015

주석은 최근 첨단 전기, 전자 제품의 핵심 소재로써 지속적인 수요 증가가 예상되는 전략 금속이다. 국내의 수요량은 2011년 기준 약 17,000톤 으로 99% 이상 수입에 의존하고 있는 실정이다. 그러나, 국내의 주석 제련 산업은 전무한 상태이며 폐자원에서 재활용하는 회수 기술도 초보 단계이다. 이러한 폐자원 발생량은 12,000톤/year이며, 약 1200억원에 달하는 규모이다. 다양한 폐자원의 선별적 전처리 요소 기술 개발 및 회수 공정 시스템 개발이 절실히 요구된다. 본 연구에서는, 주석 폐자원 중 solder 용융물 및 공정 스크랩 Lead solder, Lead-free solder 등 뿐만 아니라, ITO target 제조 시 발생하는 ITO sludge 등의 고상 폐자원으로부터 페자원의 물성을 파악하여 금속/산화물과의 파/분쇄 및 분급공정을 통하여 고품위의 주석 금속을 회수하였다. 뿐만 아니라, 고순도 주석시 발생하는 양극 슬라임 침출액 등의 액상 폐자원으로부터 희소금속의 추출 및 회수를 위해 습식 전처리 공정을 수행하였다. 침출액은 주석, 구리, 납 등의 유가금속이 이온형태로 존재하고 있으며, Chlorine이 다량 함유되어 있다. 고품위의 주석 산화물을 회수하기 위하여 침출액 내의 구리 제거 공정, Chlorine 제거 공정 등을 순차적으로 수행하여 고품위의 산화물 회수를 수행하였다.

• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.E2
• /
• pp.69-75
• /
• 2004

In this study, thin film gas sensor based on tin oxide was fabricated to examine its characteristics. Target gas is acetonitrile ($CH_3$CN) which is a blood simulant for the chemical warfare agent. Sensing materials are SnO$_2$ SnO$_2$/Pt, and Sn/Pt with thickness from 1000 to 3000 $\AA$. The sensor consists of a sensing electrode with inter-digit (IDT) type in front side and a heater in rear side. Resistance changes of sensing materials are monitored on real time basis using a data acquisition board with a 12-bit analog to digital converter. Sensitivities are measured at different operating temperatures also with different gas concentrations and film thickness. The high sensitivity is obtained for Sn (3000 $\AA$)/Pt (30 $\AA$) at 30$0^{\circ}C$ for 3 ppm. Response and recovery times were about 40 and 160 s, respectively. Repetition measurements showed very good results with $\pm$3% in full scale range.

• The Korean Journal of Ceramics
• /
• v.5 no.2
• /
• pp.125-130
• /
• 1999

After $SnO_2$ fine powder by precipitation method, Ca as crystallization inhibitor and Pd as catalyst were added to $SnO_2$ raw material by various methods. Thick film device was fabricated on the alumina substrate by mixing ethylene glycol and such mixed powders. The sensing characteristics of the device for methane gas were investigated. The most excellent gas sensing property was shown by the thick film device fabricated by Method 3 in which Ca and Pd doped $SnO_2$ powder is prepared by mixing $SnO_2$ powder, 0.1 wt% Ca acetate and 1 wt% $PdCl_2$ in deionized water and by calcining the mixture, after $Sn(OH)_4$ is dried at $110^{\circ}C$ for 36h. The sensitivity of the sensor fabricated with $SnO_2$-0.1 wt%Ca acetate-1wt%$PdCl_2$ powder heat-treated at $700^{\circ}C$ for 1h was about 86% for 5,000 ppm methane in air at $350^{\circ}C$ of the operating temperature. Response time and recovery were also excellent.

• Korean Journal of Metals and Materials
• /
• v.48 no.5
• /
• pp.430-435
• /
• 2010

Solvent extraction experiments of Rh(III) and Ir(IV) were performed on the HCl solution by using Alamine336 and TBP. The extraction percentage of Rh and Ir by Alamine336 was much higher than that by TBP. For the solvent extraction with Alamine336, the extraction percentage of Rh and Ir decreased with a HCl concentration. However, the extraction percentage of both metals by TBP was below 12% in our experimental range and increased with an increasing HCl concentration of up to 8 M. From the mixed solution of Ir with an excess SnCl$_{2}$, most of the tin was extracted by Alamine336 and TBP. However, the extraction percentage of Ir by Alamine336 was reduced and no iridium was extracted by TBP. The extraction behavior of Ir and Sn was investigated by scrubbing experiments on the loaded Ir with a SnCl$_{2}$ solution.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.162.2-162.2
• /
• 2015

플렉서블 디스플레이에 사용되는 투명전극은 벤딩에 의한 인장(tensile) 및 압축(compressive) 스트레스 하에서도 전극의 특성이 지속적으로 유지되어야 한다. 기존 OLED소자의 투명전극으로 사용되던 인듐산화물(ITO, Indium Tin Oxide)는 인듐(Indium)의 희소성 문제뿐만 아니라 벤딩에 대한 복원력이 나쁜 것으로 알려져 플렉서블 디스플레이에는 적합하지 않은 것으로 알려져 있다. 벤딩에 강하고 복원력이 우수한 투명전극 재료가 필요하게 되었다. 본 연구에서는 PEN (Polyethylene Naphthalate) 유연기판 상에 그래핀(Graphene)전극을 구현하여 벤딩에 대한 저항특성을 관찰하였고 일반적으로 많이 사용하는 Aluminum 전극과의 비교를 통해 광효율을 지속적으로 유지할 수 있는 플렉서블 OLED용 전극구현 가능성을 연구하였다. 일반적으로 Al금속은 인장 스트레스를 받음에 따라 저항이 증가하고 다시 복원되면 저항이 감소하는 특성을 갖고 있는데 인장 스트레스에 따라 저항과 늘어난 길이와의 관계는 다음과 같다. $R/R0=(L/L0)^2$ ----------------------------------------- (1) 그러나 반복된 스트레스가 가해질 경우 Al 금속 전극은 복원력을 잃고 저항이 원래대로 돌아가지 않는 문제가 발생하는데 반해 그래핀은 벌집모양의 구조를 갖고 있어 벤딩에 대한 강도가 셀 뿐만 아니라 고탄력으로 인해 복원력이 우수하여 여러 싸이클(cycle)의 벤딩 실험에 의해서도 복원력이 지속적으로 유지되었다. Al 금속 전극의 경우 벤딩 각도 또는 정도에 따라 복원력이 유지되는 구간이 있으나 반복적인 벤딩 싸이클에 의해 복원력이 감소하여 인장 스트레스에 의한 저항 증가 후 스트레스 제거 시 저항 감소가 되지 않는데 24시간 동안 전기 저항 변화를 관찰하면 수시간 후에나 저항이 어느 수준까지만 복원되는 것을 확인할 수 있었으나 복원에 오랜 시간이 소요된다는 점에서 그래핀과 비교가 된다. SEM(Scanning electron microscopy) 분석을 통해 인장 스트레스 인가/제거를 반복함에 따라 Al 금속표면이 표면에 열화되는 것을 확인하였으나 그래핀에서는 나타나지 않았다. 본 연구에서는 높은 투과도와 우수한 전기적 특성을 가지는 그래핀 투명 전도성 전극이 다양한벤딩 조건에서도 뛰어난 복원 특성을 보이는 것을 밝혀내어 차세대 투명 전극 물질로 개발하고자 하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.7
• /
• pp.589-593
• /
• 2011

[ $SnO_2$ ]nano powders were prepared by solution reduction method using tin chloride($SnCl_2{\cdot}2H_2O$), hydrazine($N_2H_4$) and NaOH. The $SnO_2$ thick films for gas sensors were fabricated by screen printing method on alumina substrates and annealed at $300^{\circ}C$ in air, respectively. XRD patterns of the $SnO_2$ nano powders showed the tetragonal structure with (110) dominant orientation. The particle size of $SnO_2$ nano powders at the ratio of $SnCl_2:N_2H_4$+NaOH= 1:6 was about 60 nm. The sensing characteristics were investigated by measuring the electrical resistance of each sensor in a test box. Sensitivity of $SnO_2$ gas sensor to 5 ppm $CH_4$gas and 5 ppm $CH_3CH_2CH_3$ gas was investigated for various $SnCl_2:N_2H_4$+NaOH proportion. The highest sensitivity to $CH_4$ gas and $CH_3CH_2CH_3$ gas of $SnO_2$ sensors was observed at the $SnCl_2:N_2H_4$+NaOH= 1:8 and $SnCl_2:N_2H_4$+NaOH= 1:6, respectively. Response and recovery times of $SnO_2$ gas sensors prepared by $SnCl_2:N_2H_4$+NaOH= 1:6 was about 40 s and 30 s, respectively.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.5
• /
• pp.515-523
• /
• 2015

In this paper, we fabricated and evaluated the gas sensor for the detection of CO gas and $NO_X$ gas among the vehicle exhaust emission gasses. The $SnO_2$ (tin dioxide) layer is used as the detection material, and the thin-film type and the nano-fiber type layers are deposited with various thicknesses using sputtering method and electro spinning method, respectively. The experiments are performed in the chamber where the gas concentration is controlled with mass flow controller. The fabricated devices are applied to the CO and $NO_X$ gas, where the device with the thinner $SnO_2$ layer shows better sensitivity. The nano-fiber has the larger surface area, and the shorter response time and recovery time are obtained. From the experimental results, both types of gas sensors successfully detect CO and $NO_X$ gases, which can be applied to measure those gases from the vehicle emissions.

• Analytical Science and Technology
• /
• v.12 no.6
• /
• pp.490-497
• /
• 1999

A hydrogen determinator was modified and installed in the glove box to analyse total hydrogen content in irradiated zircaloy tube. The analysis method of hydrogen is Inert Gas Fusion(IGF)-Thermal Conductivity Detection(TCD). The hydrogen recoveries of no tin method using Ti and Zr matrix standards, respectively, were available within $3{\mu}g$ of hydrogen. Also the smaller size of sample showed the better hydrogen recovery. It was found that the hydrogen standard of Ti matrix is avaliable to hydrogen analysis in zircaloy sample. The mean radioactivity of irradiated zircaloy sample was 10 mR/hr and hydrogen concentration was 130 ppm.

• Analytical Science and Technology
• /
• v.13 no.3
• /
• pp.297-303
• /
• 2000

Isotope-dilution inductively coupled plasma mass spectrometry was used to determine trace amounts of Cd, Cu, Pb, Ni and Zn in sediment. Sediment samples were dissolved by microwave digestion with addition of mixed acid ($HNO_3$, HF and $HClO_4$). Lead was determined after separation of alkaline and alkaline earth metals by an ammonium pyrrolidenedithiocarbarmate (APDC) solvent extraction. The other elements were determined after separation of iron, tin and titanium by hydroxide precipitation. Recovery efficiency of the analyte elements was not satisfactory, but most of matrix elements causing the isobaric interference could be effectively eliminated by the separation. Good agreement was achieved with the certified values in the analysis of the two sediment reference materials.