• Journal of Sensor Science and Technology
• /
• v.31 no.2
• /
• pp.90-95
• /
• 2022

The effect of the structure of an ITO nanoparticle film sensor on its performance was studied. A printed ITO film (P-ITO film) was fabricated on a flexible polyethylene terephthalate (PET) substrate, and the contact resistance of the electrode and sensor response change were clarified according to the detection position. The contact resistance between Ag and P-ITO was observed to be -204.4 Ω using the transmission line method (TLM), confirming that a very good ohmic contact is possible. In addition, we confirmed that the contact position of the analyte had a significant influence on the response of the sensor. Based on these results, the performance of the four types of sensors was compared. Consequently, we observed that 1) optimizing the resistance of the printed film, 2) optimizing the electrode structure and analyte input position, and 3) optimizing the electrode area are very important for fabricating a metal oxide nanoparticle (MONP) sensor with optimal performance.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.1
• /
• pp.130-133
• /
• 2010

Although many structures based on $SnO_2$ nanowires have been demonstrated, there is a limitation towards practical application due to the unwanted contact potential between the metal electrode and the $SnO_2$ nanowire. This is mostly due to the presence of the native oxide layer that acts as an insulator between the metal contact and the nanowire. In this study the contact properties between Ti/Au contacts and a single $SnO_2$ nanowire was compared to the electrical properties of a contact without the oxide layer. RIE(Reactive Ion Etching) is used to selectively remove the oxide layer from the contact area. The $SnO_2$ nanowires were synthesized by chemical vapor deposition (CVD) and dispersed on a $Si/Si_3N_4$ substrate. The Ti/Au (20nm/100nm) electrodes were formed bye-beam lithography, e-beam evaporation and a lift-off process.

• Journal of the Korean Vacuum Society
• /
• v.8 no.4B
• /
• pp.565-571
• /
• 1999

In this study, high-density plasma etching characteristics of ITO(indium tin oxide) films used for transparent electrode in dispaly devices were investigated. Plasma diagnostic and surface analysis tools were used to understand etch reaction mechanism. The etch rate of ITO was increased by the increase of reactive radicals such as H and $CH_3$ with the addition of moderate amount of $CH_4$ to Ar. However, the addition of excess amount of $CH_4$ decreased possibly due to the increased polymer formation on the ITO surface being etched. The increase of source power and bias boltage increased ITO etch rates but it decreased selectivities over under-layers $(SiO_2, Si_3N_4)$. The increase of working pressure up to 20mTorr also increased ITO etch rates, however the further increased of the pressure decreased ITO etch rates. From the analysis of XPS, a peak related to the polymer of hydrocarbon was observed on the etched ITO surface especially for high $CH_4$ conditions and it appears to affect ITO etch rates.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.4
• /
• pp.336-341
• /
• 2008

Recently, research on a flat panel display(FPD) has focused on organic light-emitting display(OLED) which has wide angle of view, high contrast ratio and low power consumption. ITO(Indium-Tin-Oxide) films are the most widely used material as a transparent electrode of OLED and also in many other display devices like LCD or PDP. The performance and efficiency of OLED is related to the surface condition of ITO coated glass substrate. The typical surface defect of glass substrate is measured for electric characteristics and physical condition for transmittance and roughness. Since ITO coated glass substrate can be destroyed for inspection about surface roughness, sheet resistance, film thickness and transmittance, precise fabrication condition should be made based on the estimated relationship. In this paper, ITO films were prepared on the commercial glass substrate by the Ion-Plating method changing the partial pressure of gas(Ar, 02) and the chamber temperature between $200^{\circ}C$ and $300^{\circ}C$. The characteristics of films were examined by the 4-point probe, supersonic thickness measurement, transmittance measurement and AFM. We estimated the relationship between processing parameters(Ar gas, O2 gas, Temperature) and properties of ITO films (Sheet Resistance, Film Thickness, Transmittance, Surface Roughness).

• Journal of Electrochemical Science and Technology
• /
• v.3 no.1
• /
• pp.24-28
• /
• 2012

The electrocatalytic activities and surface roughness of indium-tin-oxide (ITO) electrodes have been investigated after thermal treatment at 100, 150, or $200^{\circ}C$ for 30 min, 2 h, or 8 h. To check electrocatalytic activities, the electrochemical behavior of four electroactive species (p-hydroquinone, $Ru(NH_3){_6}^{3+}$, ferrocenemethanol, and $Fe(CN){_6}^{4-}$) has been measured. The electron transfer rate for p-hydroquinone oxidation and ferrocenemethanol oxidation increases with increasing the incubation temperature and the incubation period of time, but the rate for $Ru(NH_3){_6}^{3+}$ is similar irrespective of the incubation temperature and period because $Ru(NH_3){_6}^{3+}$ undergoes a fast outer-sphere reaction. Overall, the electrocatalytic activities of ITO electrodes increase with increasing the incubation temperature and period. The surface roughness of ITO electrodes increases with increasing the incubation temperature, and the thermal treatment generates many towering pillars as high as several tens of nanometer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.351.2-351.2
• /
• 2014

Indium tin oxide (ITO) has a lot of variations of its properties because it is basically in an amorphous state. Therefore, the differences in composition ratio of ITO can result in alteration of electrical properties. Normally, ITO is considered as transparent conductive oxide (TCO), possessing excellent properties for the optical and electrical devices. Quantitatively, TCO has transparency over 80 percent within the range of 380nm to 780nm, which is visible light although its specific resistance is less than $10-3{\Omega}/cm$. Thus, the solar cell is the best example for which ITO has perfectly matching profile. In addition, when ITO is used as transparent conductive electrode, this material essentially has to have a proper work function with contact materials. For instance, heterojunction with intrinsic thin layer (HIT) solar cell could have both front ITO and backside ITO. Because each side of ITO films has different type of contact materials, p-type amorphous silicon and n-type amorphous silicon, work function of ITO has to be modified to transport carrier with low built-in potential and Schottky barrier, and approximately requires variation from 3 eV to 5 eV. In this study, we examine the change of work function for different sputtering conditions using ultraviolet photoelectron spectroscopy (UPS). Structure of ITO films was investigated by spectroscopic ellipsometry (SE) and scanning electron microscopy (SEM). Optical transmittance of the films was evaluated by using an ultraviolet-visible (UV-Vis) spectrophotometer

• Laser Solutions
• /
• v.13 no.1
• /
• pp.11-15
• /
• 2010

Indium tin oxide (ITO) provides high electrical conductivity and transparency in the visible and near IR (infrared) wavelengths. Thus, it is widely used as a transparent electrode for the fabrication of liquid crystal displays (LCDs) and organic light emitting diode displays (OLRDs), photovoltaic devices, and other optical applications. Lasers have been used for removing coating on polymer substrate for flexible display and electronic industry. In selective removal of ITO layer, laser wavelength, pulse energy, scan speed, and the repetition rate of pulses determine conditions, which are efficient for removal of ITO coating without affecting properties of the polymer substrate. ITO coating removal with a laser is more environmentally friendly than other conventional etching methods. In this paper, pattering of ITO film from polymer substrates is described. The Yb:KGW femtosecond laser processing system with a pulse duration of 250fs, a wavelength of 1030nm and a repetition rate of 100kHz was used for removing ITO coating in air. We can remove the ITO coating using a scanner system with various pulse energies and scan speeds. We observed that the amount of debris is minimal through an optical and a confocal microscope, and femtosecond laser pulses with 1030nm wavelength are effective to remove ITO coating without the polymer substrate ablation.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.1
• /
• pp.46-49
• /
• 2016

A thin film transistor (TFT) has been fabricated using the amorphous 0.5 wt% Si doped zinc-tin-oxide (a-0.5 SZTO) with different electrodes made of either aluminium (Al) or titanium/aluminium(Ti/Al). Contact resistance and total channel resistance of a-0.5SZTO TFTs have been investigated and compared using the transmission line method (TLM). We measured the total resistance of 1.0×10² Ω/cm using Ti/Al electrodes. This result is due to Ti, which is a material known for its adhesion layer. We found that the Ti/Al electrode showed better contact characteristics between the channel and electrodes compared with that made of Al only. The former showed a less contact and total resistance. We achieved high performance of the TFTs characteristic, such as Vth of 2.6 V, field effect mobility of 20.1 cm² V⁻¹s⁻¹, S.S of 0.9 Vdecade⁻¹, and on/off current ratio of 9.7×10⁶ A. It was demonstrated that the Ti/Al electrodes improved performance of TFTs due to enhanced contact resistance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.450-450
• /
• 2007

Indium tin oxide (ITO), which is used as an electrode in organic thin film transistors (OTFT), was modified with a self-assembled monolayer (SAM) by wet chemical surface modification. The surface of the ITO was treated by dipping method in a solution of 2-chloroethane phosphonic acid (2-CEPA) at room temperature. The work function in the ITO which was modified with the SAM in the 2-CEPA had 5.43eV. A surface energy and a transmittance were unchanged in an error range. On this study, therefore, possibility of ohmic contact is showed in the interface between the ITO and the organic semiconductors. These results suggest that the treatment of the ITO with the SAM can greatly enhance the performance of the OTFT.

• Journal of IKEEE
• /
• v.25 no.1
• /
• pp.69-75
• /
• 2021

In this work, we consider the fabrication method and electrical characteristics of dye-sensitized solar cells (DSSCs), which use titanium (Ti) metal thin films to replace expensive fluorine tin oxide (FTO) electrodes. The thickness of the Ti thin film was changed by adjusting the deposition time of the Ti, and the surface resistance decreased as the thickness of the Ti thin film became thicker. The thickness of the Ti thin film was shown to be similar to the surface resistance of the FTO thin film at approximately 190nm and the DSSC with a thickness of approximately 250nm showed the highest energy conversion efficiency of 4.24%. Furthermore, the possibility of commercialization was confirmed by fabricating and evaluating the DSSC module.