• Journal of Power Electronics
• /
• v.11 no.2
• /
• pp.156-162
• /
• 2011

The control loop time delay caused by sampling, the zero-order-holder effect and calculations is inevitable in the digital control of dc-dc switching converters. The time delay will limit the bandwidth of the control loop and therefore degrade the transient performance of digital systems. In this paper, the quantization time delay effects with different time delay values based on a generic second-order system are analyzed. The conclusion that the bandwidth of digital control is reduced by about 20% with a one cycle delay and by 50% with two cycles of delay in comparison with no time delay is obtained. To compensate the time delay and to increase the control loop bandwidth, a duty ratio predictive control scheme based on linear extrapolation is proposed. The compensation effect and a comparison of the load variation transient response characteristics with analogy control, conventional digital control and duty ratio predictive control with different time delay values are performed on a point-of-load Buck converter by simulations and experiments. It is shown that, using the proposed technique, the control loop bandwidth can be increased by 50% for a one cycle delay and 48.2% for two cycles of delay when compared to conventional digital control. Simulations and experimental results prove the validity of the conclusion of the quantization effects of the time delay and the proposed control scheme.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.119.3-119
• /
• 2001

When building a network-based real-time control system, a network-induced delay time should be surly considered for real time schedulability to be guaranteed. The network delay time on end-to-end communication has been analyzed theoretically and modeled mathematically from many previous works. There also exist any other delay element not considered before. In this paper, the remote feedback control system using the CAN protocol is proposed to control three axes´ manipulator arm and the application layer of CAN is modeled to analyze the delay elements defined by three types of time delay: Software delay time, Controller delay time, and Access delay time, in details. The analyzed results are used as an important component to determine PID gains of the proposed system. The effect of the delay time on the control performance is evaluated by com paring the response characteristics of the control system through simulation.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.6
• /
• pp.564-572
• /
• 2008

The performance of the direct adaptive time-delay command shaping filter depends on the select time-delay. In the previously introduced direct adaptive command shaping filter, however, the time-delay value is fixed and only the magnitudes of the impulses are learned. In this paper, the authors introduce a new scheme to adapt the time-delay which is to be used in conjunction with the direct adaptive command shaping for the improved vibration suppression in flexible motion system. In order to formulate the time-delay adaptation scheme, the authors have analyzed the effect of the time-delay value on the performance of the direct adaptive command shaping filter. By modifying the direct adaptation formula based on the analysis result the authors have established a set of equations to adapt the time-delay toward the optimal value. Simulation results show the effectiveness of the proposed time-delay adaptation approach for the improved vibration suppression.

• The Korean Journal of Applied Statistics
• /
• v.36 no.5
• /
• pp.415-445
• /
• 2023

Oftentimes, the time dependent treatment covariate and the time dependent confounders exist in observation studies. It is an important problem to correctly adjust for the time dependent confounders in the propensity score analysis. Recently, In the survival data, Hade et al. (2020) used a propensity score matching method to correctly estimate the treatment delay effect when the time dependent confounder affects time to the treatment time, where the treatment delay effects is defined to the delay in treatment reception. In this paper, we proposed the Cox model based marginal structural model (Cox-MSM) framework to estimate the treatment delay effect and conducted extensive simulation studies to compare our proposed Cox-MSM with the propensity score matching method proposed by Hade et al. (2020). Our simulation results showed that the Cox-MSM leads to more exact estimate for the treatment delay effect compared with two sequential matching schemes based on propensity scores. Example from study in treatment discontinuation in conjunction with simulated data illustrates the practical advantages of the proposed Cox-MSM.

• Journal of ILASS-Korea
• /
• v.3 no.1
• /
• pp.19-26
• /
• 1998

The effect of mixture component makes a nelay time and a long total combustion period $\tau_{p\;max}$. The flame propagation delay $\tau_{df}$ was determined by the record of current ion. The pressure release delay $\tau_{dp}$ and $\tau_{p\;max}$ were determined by the indicated pressure diagram in constant volume of the combustion chamber. The results are as follows: 1) The ignition delay $\tau_t$ time takes the minimum value around $\Phi=1.15$. 2) $\tau_{df}$ and $\tau_t$ time increased according to the increases of the concentrated dilution gases, because the adiabatic flame temperature decreased due to the increases of the heat capacity. But dilution gases have little effect on flame nucleus formation delay 3) The relation between $\tau_t$ time and reciprocal laminar burning velocity is almost linear. 4) The increase of the propagation length is accompanied with increased ratio of the $\tau_{df},\;\tau_{dp},\;\tau_{t},\;\tau_{p\;max}$.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.1
• /
• pp.49-57
• /
• 2016

A modular multilevel converter is widely adapted for a high-voltage direct current power transmission system. This study proposes a design methodology for a novel digital control that mitigates the negative effects caused by time delay, including communication transport delay for a modular multilevel converter. The modeling and negative effect of time delay are analyzed theoretically in a frequency domain, and its compensation methodology based on an inverse model is described fully with practical considerations. The proposed methodology is verified through several simulation results using a modular 21-level converter system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.43-44
• /
• 2006

The performance of the direct adaptive time-delay filter depends on the select time-delay. In this paper, the authors introduce a new scheme to adapt the time-delay which is to be used in conjunction with the direct adaptive command shaping for the improved vibration suppression in flexible motion system. In order to formulate the time-delay adaptation scheme, the authors have analyzed the effect of the time-delay value on the performance of the direct adaptive command shaping filter. By modifying the direct adaptation formula based on the analysis result the authors have established a set of equations to adapt the time-delay toward the optimal value. Simulation results show the effectiveness of the proposed time-delay adaptation approach for the improved vibration suppression.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.8 s.227
• /
• pp.1075-1086
• /
• 2004

In this paper, Time Delay Control(TDC) for robot manipulators is analyzed and its problems are founded. In order to remedy the problems, the enhanced controller is proposed and analyzed. The effect of friction associated with TDC is reported and its cause is presented. Through the analysis, simulation and experiment, it is shown that the friction effect causes serious degradation in control performance and that it is a result of the error of Time Delay Estimation(TDE) in TDC. In order to remedy the problems, TDC combined with Internal Model Control(IMC) concept is proposed. The proposed compensator is effective enough to handle the bad effect of friction, and is so simple and efficient as to match positive attribute of TDC. The simulation and experimental results show the effectiveness of proposed controller against the friction of the robot manipulators.

• Journal of ILASS-Korea
• /
• v.25 no.3
• /
• pp.119-125
• /
• 2020

In this paper, we used Helmholtz solver based on 3D finite element method to quantitatively analyze the effects of change of gain, time delay and time delay spread, which are the main variables of flame transfer function, on combustion instability in gas turbine combustor. The effects of the variable of flame transfer function on the frequency and growth rate, which are the main results of combustion instability, were analyzed by applying the conventional heat release fluctuation model and modified one considering the time spread. The analysis results showed that the change of gain and time delay in the same resonance mode affected the frequency of the given resonance modes as well as growth rate of the feedback instability, however, the effect of time delay spread was not relatively remarkable, compared with the dominant effect of time delay.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.68.1-68
• /
• 2001

This paper discusses tracking position control of linear actuator that has a time delay. The time delay happens when the process reads the sensor data and sends the control input to the plant located at a remote site in distributed control system. In this thesis, the time delay between the linear actuator and the discrete PID controller has constant value due to buffer device so the time delay can be modeled by Pade approximation but the large position error of the linear actuator is generated by the time delay. Therefore, the Smith predictor is used for tracking position control of the linear actuator with the time delay in order to minimize the effect of the time delay. The experimental and simulation results show that the ...