• 대한기계학회논문집A
• /
• 제24권2호
• /
• pp.535-542
• /
• 2000

This paper presents a method for the dynamic analysis of constrained multibody systems undergoing abrupt collision. The proposed method uses a longer time interval to check collision than that of c onventional method. This reduces the computational effort significantly. To calculate collision points on two colliding rigid bodies, one may introduce constraints of contact. However, this causes reduction of degree of freedom and difficulty of numerical analysis. The proposed method can calculate collision points without above mentioned problems. Three numerical examples are given to demonstrate the computational efficiency and the usefulness of the proposed method.

• 대한전자공학회논문지TC
• /
• 제43권8호
• /
• pp.35-46
• /
• 2006

RFID 리더는 자신이 전송한 명령에 대한 태그의 응답을 수신하여 태그를 인식한다. 이때 근접한 거리에 위치하고 있는 리더들이 동일한 주파수를 이용하거나, 여러 리더가 동시에 하나의 태그에 명령을 전송하는 경우 서로 간섭을 일으킬 수 있는데 이를 RFID 리더 충돌이라고 한다. 리더 충돌이 발생하면 리더의 명령이 태그에게 전달되지 않거나 전송된 명령에 대해 태그가 올바르게 응답할 수 없다. 따라서 RFID 국제 표준 및 논문들은 리더 충돌을 줄이기 위한 기법들을 규정하거나 제안하고 있다. 이 중 Colorwave와 Enhanced Colorwave는 TDM(Time Division Multiplex) 기반의 프레임 알로하 방식을 이용한 리더충돌방지 기법으로 충돌 확률에 따라 프레임의 크기를 변경하여 효과적으로 리더 충돌을 줄일 수 있다. 그러나 이 알고리즘들은 충돌을 경험한 리더들이 충돌을 피하기 위해 자신의 슬롯을 새롭게 선택하는 과정에서 불필요한 충돌을 발생시킬 수 있다는 단점을 가지고 있다. 충돌 발생 리더들이 프레임 내의 임의의 슬롯으로 이동하기 때문이다. 따라서 본 논문에서는 프레임 내 슬롯의 점유 여부를 모니터링 하여 리더 충돌이 발생한 경우 리더들이 점유할 확률이 가장 낮은 슬롯을 선택하는 새로운 리더 충돌방지 알고리즘을 제안하고 시뮬레이션을 이용하여 성능을 분석한다.

• 대한전자공학회논문지TC
• /
• 제44권10호
• /
• pp.47-54
• /
• 2007

시간 영역에서 나노 초 이하의 임펄스 신호를 이용한 초광대역 무선 통신 (Impulse-radio-based ultra wideband:IR-UWB 기술은 반송파 없이 통신을 진행하기 때문에 시간 축에서 데이터를 연속적으로 전송하지 않으며, 이러한 특징을 사용하면 다중 사용자 환경에서 패킷의 충돌을 효율적으로 조절 할 수 있다. 본 논문에서는 IR-UWB 환경을 분석하고, 이에 특화된 충돌 분산이라는 패킷의 충돌을 펄스의 충돌로 분해하는 새로운 패킷충돌 패러다임을 제시한다. 충돌 분산 방안에서는 각각의 노드가 독립된 펄스 간격으로 임의의 시간에 분산된 환경에서 데이터를 전송하며, 패킷의 충돌을 펄스의 충돌로 분해함으로써 패킷의 충돌로 인한 전체 패킷의 손실을 막을 수 있다. 또한 제시된 방안을 이용하여 패킷의 충돌로 인한 패킷 에러가 줄어들 수 있고, 데이터의 실시간 전송을 보장할 수 있음을 분석을 통해 제시하였다.

• 한국멀티미디어학회논문지
• /
• 제19권10호
• /
• pp.1808-1815
• /
• 2016

TPSN(Timing-sync Protocol for Sensor Networks), the representative of time synchronization protocol, has been already developed to provide time synchronization among nodes in wireless sensor networks. Even though the TPSN's method has been referenced by so many other time synchronization schemes for resource-constrained networks like wireless sensor networks or low power personal area networks, it has some inefficiency in terms of power consumption and network-wide synchronization time (or called convergence time). The main reason is that each node in TPSN needs waiting delay to solve the collision problem due to simultaneous transmission among competing nodes, which causes more power consumption and longer network convergence time for a network-wide synchronization. In this paper an improved scheme is proposed by changing message exchange method among nodes. The proposed scheme not only shortens network-wide synchronization time, but also reduce collision traffic which lead to needless power consumption. The proposed scheme's performance has been evaluated and compared with an original scheme by simulation. The results are shown to be better than the original algorithm used in TPSN.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1993년도 한국자동제어학술회의논문집(국내학술편); Seoul National University, Seoul; 20-22 Oct. 1993
• /
• pp.423-427
• /
• 1993

A velocity planning method is proposed that ensures collision-free and minimal delay-time motions for two robotic manipulators and auxiliary equipments. Additional path, which makes robot start with possible largest speed, is added to the original prescribed path of one of two robots, and this running start along the additional path reduces delay time introduced to avoid collision between the robots and therefore reduces total traveling time.

• 자동차안전학회지
• /
• 제5권2호
• /
• pp.17-23
• /
• 2013

This paper describes an algorithm for Advanced Emergency Braking(AEB) with tire-road friction coefficient estimation. The AEB is a system to avoid a collision or mitigate a collision impact by decelerating the car automatically when forward collision is imminent. Typical AEB system is operated by Time-to-collision(TTC), which considers only relative velocity and clearance from control vehicle to preceding vehicle. AEB operation by TTC has a limit that tire-road friction coefficient is not considered. In this paper, Tire-road friction coefficient is also considered to achieve more safe operation of AEB. Interacting Multiple Model method(IMM) is used for Tire-road friction coefficient estimation. The AEB algorithm consists of friction coefficient estimator and upper level controller and lower level controller. The numerical simulation has been conducted to demonstrate the control performance of the proposed AEB algorithm. The simulation study has been conducted with a closed-loop driver-controller-vehicle system using using MATLAB-Simulink software and CarSim Vehicle model.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제2권6호
• /
• pp.299-311
• /
• 2008

The Radio Frequency IDentification (RFID) system is a contactless automatic identification system, which comprises readers and tags. In RFID systems, a reader collision occurs when there is interference in communication between one reader and the tags, due to the signals from other readers. The reader collision problem is considered as the fundamental problem affecting high density RFID reader installations. In this paper, we analyze the existing reader anti-collision algorithms. We also propose a pulse protocol-based reader anti-collision algorithm using slot occupied probability (SOP). The implementation of this improvement is simple, yet it effectively mitigates most reader collisions in dense reader mode, as shown in our simulation. That is, the proposed algorithm reduces the identification time, and increasesthe system throughput and system efficiency compared with the conventional reader anti-collision algorithms.

• Journal of Electrical Engineering and information Science
• /
• 제2권3호
• /
• pp.51-60
• /
• 1997

A practically applicable collision free trajectory planning technique for tow robot systems is proposed. The robot trajectories considered in this work are composed of many segments, an at the intersection points between segments robots stop to assemble, weld, ordo other jobs by the attached a end-effectors. The proposed method is based on the Planning-Coordination Decomposition where planning is to find a trajectory of each robot independently according to their tasks and coordination is to find a velocity modification profile to avoid collision with each other. To fully utilize the independently planned trajectories and to ensure no geometrical path deviation after coordination, we develop a simple technique added the minimal delay time to avoid collision just before moving along path segments. We determine the least delay time by the graphical method in the Coordination space where collisions and coordinations are easily visualized. We classify all possible cases into 3 group and derive the optimal solution for each group.

• 대한임베디드공학회논문지
• /
• 제17권2호
• /
• pp.115-121
• /
• 2022

This paper proposes a distributed model predictive formation control algorithm for a group of unmanned ground vehicles (UGVs) with guaranteeing collision avoidance between UGVs. Generally, the model predictive control based formation control has a disadvantage in that it takes a long time to compute control inputs when considering collision avoidance between UGVs. In this paper, in order to overcome this problem, the formation control algorithm is implemented in a distributed manner so that it could be individually controlled. Also, a collision-avoidance method considering real-time is proposed. The proposed formation control algorithm is implemented based on robot operating system (ROS), open source-based middleware. Through the various simulation tests, it is confirmed that the formation control of five UGVs is successfully performed while avoiding collisions between UGVs.

• Journal of Ship and Ocean Technology
• /
• 제5권3호
• /
• pp.36-44
• /
• 2001

The collision energy absorbing characteristics of side structure of the LNG carriers which have the cargo containment systems of the spherical and the membrane types are compared. A failure mechanism of the double hull side structures of 130, 000 $m^3$ class LNG carriers under sideways collision event has been simulated by using the detailed finite element calculations. In ship collision analysis, the finite element method based on explicit time integration has been use[1 with much success. Finite element modeling techniques for detail description of structural members antral ship motion regarding the dynamic behavior allowed to investigate the effect of bow shape and the initial contact position on side shell of collided ship. In the numerical simulations of the ship-to-ship sideways collision, the effect of the colliding bow shapes and the change of the colliding ship draft are investigated. The critical collision energy which is absorbed by a side structure of a collided ship until the fore-end of colliding ship arrives at the boundary of the cargo tank is calculated. The critical speed of specified colliding ships which can not penetrate the boundary of the LNG cargo tank of the collided ship under collision accident if evaluated.