• Proceedings of the KIEE Conference
• /
• 2004.04a
• /
• pp.278-280
• /
• 2004

판토그라프는 전차선(catenary)으로부터의 전류를 차량에 전달하는 장치로서 전동차 지붕 위에 설치되어 있다. 판토그라프의 설계 목표는 고속 및 다양한 환경 조건하에서 연속적이고 일정한 량의 전류를 차량에 전달하도록 하는 것이다. 열차가 고속화될수록 전류의 흐름이 중단되는 이선, 접촉선과 판토그라프 집전판의 마모, 공력 소음 등이 큰 문제로 대두되며, 이들 문제들이 고속용 판토그라프의 설계 기술에서 중요시되고 있다. 특히 이선은 동력 전달이 중단될 뿐만 아니라 이선시에 발생하는 아크로 인한 마모 증대, 통신 장해를 일으킨다. 유럽과 일렬에서는 그러한 문제를 인식하고 고속용 판토그라프에 대한 연구를 활발히 진행하고 있다. 또한 저속전철이나 고속전철을 운행하는 나라에서는 기존의 가선계를 그대로 이용하면서 고속화를 달성하기 위하여 기존 가선계에 대한 최적의 판토그라프 설계에 노력을 기울이고 있다. 본 논문에서는 국내 기존선 고속화에 필요한 최고속도 180km/h급 틸팅차량시스템의 핵심 구성요소인 판토그라프 제어기술에 대한 연구를 통하여 보다 안전한 틸팅차량용 판토그프사양 개발하는데 목적이 있다.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.5
• /
• pp.572-577
• /
• 2011

Curve squealing of inter-city railway vehicle is a noise with high acoustic pressure and rather narrow frequency spectra. This noise turns out to be very annoying for the people living in the neighborhood of locations and the passenger in railway vehicle where this phenomenon occurs. Squealing is caused by a self-exited stick-slip oscillation in the wheel-rail contact. Curve squeal noise of railway vehicles that passed by a factor of the speed limit, so to overcome in order to improve running performance is one of the largest technology. In the present paper, characteristic of squeal noise behavior at the Hanvit-200 tilting train test-site. Curve squealing of railway wheels/rail contact occurs in R400~ R800 curves with a frequency range of about 4~11 kHz. If the curve is less than the radius of wheel frail contact due to |left-right| noise level difference (dBA) shows a significant effect of squeal noise were more likely.

• Journal of the Korean Society for Railway
• /
• v.12 no.2
• /
• pp.309-314
• /
• 2009

When a train enters into a tunnel, a compression wave is generated by a front nose and a expansion wave is generated by a rear tail respectively. The interaction between pressure waves and the train makes the internal and external pressure of the train change dramatically. In this paper, we had measured the internal and external pressure variations of TTX and analyzed the pressure variations as the tunnel length. Also, the rate of internal pressure variations were investigated with the current airtight condition of TTX. In short tunnels, the internal and external pressure variation were not large because the superposition of pressure waves was not happened. In long tunnels, however, the rapid and large pressure variations were shown because of the superpositions between the same sort of pressure waves, such as expansion wave and expansion wave or compression wave and compression wave. In specific length tunnels, the pressure variation and the pressure variation rates were largely lessened because the compression wave and expansion wave were superposed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.1
• /
• pp.98-105
• /
• 2010

Squeal, a kind of self-excited vibration, is generated by the friction between the disc and the friction materials. It occurs at the ending stage of the braking process, and radiates and audible frequency range of 1 kHz to 10 kHz. Squeal is generated from unstability because of the coupling between the translation and rotation of the system. This instability is caused by the follower force and follower force is normal component of the friction force. In this paper modal analysis of wheel brake system was performed in order to predict the squeal phenomenon. It was shown that the prediction of system instability is possible by FEM. A finite element model of that brake system was made. Some parts of a real brake was selected and modeled. Modal analysis method performs analyses of each brake system component. Experimental modal analysis was performed for each brake components and experimental results were compared with analytical results from FEM. To predict the dynamic unstability of a whole system, the complex eigenvalue analysis for assembly modeling of components confirmed by modal analysis is performed. The finite element models of the disk brake assembly have been constructed, and the squeal noise problems have been solved by complex eigenvalue analysis. The complex eigenvalue analysis results compared with real train test.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.207-211
• /
• 2005

The Korean Tilting Train eXpress (TTX) with service speed of 180km/h have been developing using hybrid design concept combined with a sandwich composite structure for the carbody and stainless steel structure for the underframe to match the challenging demands with respect to cost efficient lightweight design for railway carriage structures. The sandwich composite structure was used to minimize the weight of the carbody, while the metal underframe was used to modify the design easily and to keep the strength of underframe for the installation of the electrical equipments. The sandwich composite structure was 23 meters long, 3 meters wide and 2.7 meters high, and cured as one body in a large autoclave equipment with the length of 30 meters and the diameter of 5 meters. The joint part between the carbody structure made of sandwich composites and the metal underframe was joined by the proposed design.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.331-336
• /
• 2005

A lot of manufacturing knowledge and method have applied to increase manufacturing efficiency in industry field. DES(Discrete Event Simulation) is one of solution to deal with manufacturing problems in factory. Beginning of research, old maintenance system of KNR ( Korea National Railroad) and its technical problems are basically investigated. KNR has maintained railway vehicle with their own solution based on experience. Very advanced railway vehicles such as KTX (Korea Train Express) and TTX(Tilting Train Express) will be difficult to maintain with their old maintenance method. In order to apply knowledge of DES, maintenance field of railway must be considered. Imaginary maintenance machine are selected to variable of DES. Maintenance capability of each machine will be evaluated base on imaginary data from imaginary machine. The machine could be very expensive as well as difficult to replace. Target of research is minimization of number of machine in railway workshop. So basic knowledge of discrete event simulation is introduced. Then five essential stages of discrete event simulation are provided. Each maintenance case defined as event. Each event is discrete and simulated base on different case such as one maintenance line with one machine and one maintenance line with two machines in railway workshop. simple maintenance method, discrete event simulation, will be come out very powerful in complicate maintenance system and will be helpful to reduce maintenance cost as well as maintenance labor.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.627-632
• /
• 2010

Recently the research for lightening the railway vehicle is actively made according to the demand of the environment-friendly technology development contributing to the energy cost reduction and the green growth. The railway vehicle lightweight research is expanded to the load-supporting first structure from the secondary structure which doesn't support the load. After the composite car body development used in the Korean tilting train is completed, the composite bogie frame development in which the weight reduction efficiency is large is progressed. In this paper, distributed strain was monitored when the train load was added to the central part of the composite bogie side-frame. By using the optical fiber which was attached to the lower part of the side-frame and the developed Brillouin correlation domain analysis (BOCDA) system, the strain distribution could be measured with 3cm step over 3m section. This strain distribution was compared with the design value by the FE analysis when the load of 14ton and 18ton added. This experiment can verify the manufactured composite bogie side-frame.

• 한국전산유체공학회:학술대회논문집
• /
• 2003.08a
• /
• pp.132-138
• /
• 2003

The optimal design for a leading car considering the aerodynamic resistance is required on the high-speed train due to increasing of ratio of drag force with proportion for the square of velocity. The aerodynamic analysis using CFD in the stage of concept design offers more economical analysis method which is used to estimate the influence of flow and pressure around the leading car than the experimental method using the Mock-up. In this study, we want to assist the artistic design with aerodynamics analysis in order to get the optimal design for leading car with the operation speed of 180km/h. The results of aerodynamic analysis for two leading car models which one is expressed with lineal beauty and the other is with curvaceous beauty are compared with each other and they offer the proposal of modification for two models in order to decrease the drag force. The shape of curvaceous model is better for the pressure force but slightly worse for the viscous force than the other. The Fluent software is used for the calculation of flow profile in this study.

• Proceedings of the KSR Conference
• /
• 2003.10c
• /
• pp.351-357
• /
• 2003

The optimal design for a leading car considering the aerodynamic resistance is required on the high-speed train due to increasing of ratio of drag force with proportion for the square of velocity. The aerodynamic analysis using CFD in the stage of concept design offers more economical analysis method which is used to estimate the influence of flow and pressure around the leading car than the experimental method using the Mock-up. In this study, we want to assist the artistic design with aerodynamics analysis in order to get the optimal design for leading car with the operation speed at 180km/h. The results of aerodynamic analysis for two leading car models which one is expressed with lineal beauty and the other is with curvaceous beauty are compared with each other and they offer the proposal of modification for two models in order to decrease the drag force. The shape of curvaceous model is better for the pressure force but slightly worse for the viscous force than the other. The Fluent software is used for the calculation of flow profile in this study.

• International Journal of Railway
• /
• v.1 no.3
• /
• pp.113-116
• /
• 2008

The long-tenn exposure of polymeric composite materials to extreme-use environments, such as pressure, temperature, moisture, and load cycles, results in changes in the original properties of the material. In this study, the effect of combined environmental factors such as ultraviolet ray, high temperature and high moisture on mechanical and thermal analysis properties of glass fabric and phenolic composites are evaluated through a 2.5 KW accelerated environmental aging tester. The environmental factors such as temperature, moisture and ultraviolet ray applied of specimens. A xenon-arc lamp is utilized for ultraviolet light and exposure time of up to 3000 hours are applied. Several types of specimens - tensile, bending, and shear specimens that are warp direction and fill direction are used to investigate the effects of environmental factors on mechanical properties of the composites. Mechanical degradations for tensile, bending and shear properties are evaluated through a Universal Testing Machine (UTM). Also, storage shear modulus, loss shear modulus and tan a are measured as a function of exposure time through a Dynamic Mechanical Analyzer (DMA). From the experimental results, changes in material properties of glass fabric and phenolic composites are shown to be slightly degraded due to combined environmental effects.