• Steel and Composite Structures
• /
• 제23권1호
• /
• pp.67-85
• /
• 2017

This study investigates numerically the behavior of tilted angle shear connectors embedded in solid concrete slabs. Two different tilted angle connectors were used, titled angle with 112.5 and 135 degrees between the angle leg and steel beam flange. A nonlinear finite element model was developed to simulate and validate the experimental push-out tests. Parametric studies were performed to investigate the variations in concrete strength and connector's dimensions. The results indicate that the ultimate strength of a tilted angle shear connector is directly related to the square root of the concrete compressive strength. The effects of variations in the geometry of tilted angle connectors on the shear capacity are discussed in details. Based on the numerical analyses, two equations are proposed to estimate the ultimate capacity of tilted angle shear connectors of 112.5 and 135 degrees in the defined range of parameters.

• 한국전기전자재료학회논문지
• /
• 제18권7호
• /
• pp.635-640
• /
• 2005

In this paper, we have improved a novel high tilted optically compensated bend (OCB) (HTOCB) mode by using high tilt angle that was generated by the unique baking condition on the homeotropic alignment layer. The high tilt angle of liquid crystal (LC) was generated by new alignment process that tilt angle changed homeotropic state to homeogenous state using Hot-plate equipment; we obtained about $40\~50^{\circ}$ tilt angle with negative and positive dielectric anisotropy on the homeotropic polyimide (PI), and then LC tilt angle decreased as increasing baking temperature and time. At last, we obtained about $10^{\circ}$ with positive type NLC $({\Delta}n>0)$. Also, the LC tilt angle of positive type NLC $({\Delta}n>0)$ decreased as increasing rubbing strength at the same baking temperature and time. The novel LC operating mode (HTOCB) that used the high tilt angle by the new alignment method was improved. The response time of the novel HTOCB cell was faster than that of conventional OCB cell. We suggest that the developed the novel HTOCB cell using control of tilt angle on the homeotropic surface is a promising technique for the achievement of a fast response time and a high contrast ratio.

• 한국정보전자통신기술학회논문지
• /
• 제1권2호
• /
• pp.57-63
• /
• 2008

In this paper, we develop the Hipass antenna that is used in electronic tall-gate charging (ETC) system in Korea expressway. This antenna has circular polarized characteristics, and especially has 45 degree tilted beam properties. These properties are very effective in ETC communication between the vehicle antenna and the tall-gate antenna. To achieve these properties on a small microstrip type antenna structure, we propose a annular ring microstrip antenna with stubs. When the length and angle of stubs are changed, the direction of the circular polarized beam is generally tilted by $45^{\circ}$ in elevation angle. Especially, by using the stubs in inner area or outer area of ring antenna, it is found that the beam direction of in azimuth angle can be rotated.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 학술대회 및 기술세미나 논문집 디스플레이 광소자
• /
• pp.45-46
• /
• 2006

We have studied the viewing angle control using a twist nematic liquid crystal display (TN-LCDs). These TK-LCDs have the characteristics, of which is not good image quality, for examples low Contrast ratio and gray scale inversion problems at upper and down viewing direction. TN-LCDs have the function of switching between the wide viewing mode and narrow viewing angle mode using two tilted LC layers. Tilt angles of the two LC layers, $14^{\circ}$ and $60^{\circ}$ were required in both wide viewing angle and narrow viewing angle modes, respectively. Consequently, this device is compatible with two image performances of which the wide viewing angle mode and Narrow viewing angle mode.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.699-702
• /
• 2006

We have developed twist nematic liquid crystal displays (TN-LCDs), of which the viewing angle can be controlled. The TN-LCDs have the function of switching between the wide viewing mode and narrow viewing angle mode using two tilted LC layers. Tilt angles of the two LC layers, $14^{\circ}$ and $60^{\circ}$ were required in both wide viewing angle and narrow viewing angle modes, respectively. In this way, the viewing angle range in terms of contrast ratio 5:1 can be switched from $120^{\circ}$ to $60^{\circ}$.

• 설비공학논문집
• /
• 제8권1호
• /
• pp.1-12
• /
• 1996

In lots of application to heat exchanger systems, closed two-phase thermosyphons are tilted from a horizontal. If the tilt angle, especially, is less than 30$^{\circ}$, the operational performances of thermosyphon are highly dependent on tilt angle. The present study was conducted to better understand such operational behaviors as mech-anni는 of phase change, and flow patterns inside a tilted thermosyphon. For experiment, an ethanol thermosyphon with a 35% of fill charge rate was designed and manufactured, using a copper tube with a diameter 19mm and a length 1500mm. Through a series of test, the tilt angle was kept constant at each of 4 different values in the range 10~25deg. and the heat supply to the evaporator was stepwisely increased up to 30㎾/$m^2$. When a steady state was established to the thermosyphon for each step of thermal loads, the wall temperature distribution and vapor temperature at the condenser were measured. The wall temperature distributions demonstrated a formation of dry patch in the top end zone of the evaporator, with a values of temperature 20~4$0^{\circ}C$ higher than the wetted surface for a moderate heat flux q≒20㎾/$m^2$. Inspite of the presence of hot dry patch, however, the mean values of boiling heat transfer coefficient at the evaporator wall were still in a good agreement with those predicted by Rohsenow's formula, which was based on nucleate boiling. For the condenser, the wall temperatures were practically uniform, and the measured values of condensation heat transfer coefficient were 1.7 times higher than the predicted values obtained from Nusselt's film condensation theory on tilted plate. Using those two expressions, a correlation was formulated as a function of heat flux and tilt angle, to determine the total thermal resistance of a tilted thermosyphon. The correlation formula showed a good agreement with the experimental data within 20%.

• 한국전자파학회논문지
• /
• 제14권2호
• /
• pp.202-208
• /
• 2003

본 논문에서는 기생 패치와 구동기 패치가 서로 다른 층에서 H-plane 에지 결합과 broadside 결합을 통해 고이득과 큰 틸팅 각도를 얻을 수 있는 위성 방송 수신용의 마이크로스트립 패치 배열 안테나를 제안하였다. 제안된 안테나는 고가의 유전체 기판 대신에 폴리에스터 동장 적층 필름과 폼을 사용하여 16$\times$8 배열로 설계 제작되었으며, 이득 22.9 dBi, 3dB 빔 폭 4.6$^{\circ}$, 그리고 broadside 방향에서 43.9$^{\circ}$기울어진 빔 특성을 가지고 있다.

• 한국태양에너지학회 논문집
• /
• 제38권3호
• /
• pp.1-20
• /
• 2018

It is a very important and fundamental process to know accurately the intensity of the solar energy coming into the installed module considering the tilted angle. Europe and the US commonly use a program called PVsyst to convert the global horizontal irradiation to global irradiation on tilted plane. There are two types of models that PVsyst uses to convert to irradiation on tilted plane. In this paper, Perez model, which is a decomposition model and Perez model, which is a transposition model used in PVsyst, are applied based on global horizontal irradiation and global irradiation on tilted plane measured in a specific area. The comparison of the decomposition model shows the effect of the transpostion model on global irradiation on tilted plane conversion by comparing the ratio of the horizontal diffuse irradiation amount of the Watanabe model which are highly trusted in Asia and the Perez model. The comparison of transposition model confirm the error between the measured data and the calculated value which is applied Perez model to global horizontal irradiation decomposed by Perez model and Watanabe model. Based on the two comparisons, This paper propose a method to confirm the reliability of transposition model and reduce the error when PVsyst is used in Korea.

• 천문학회보
• /
• 제35권2호
• /
• pp.30.2-30.2
• /
• 2010

A direct tilted-ring fitting method allows us to investigate kinematic structure of spiral galaxies. By employing the method to high-resolution HI data cubes, we can more easily trace warp characteristics of spiral galaxies than ever. In this contribution, we make use of TiRiFiC to VLA HI data cube of spiral galaxies in Virgo cluster, and present our preliminary yet interesting results. The TiRiFiC (Tilted-Ring-Fitting-Code) is publicly available code that provides 'best-fit' tilted-ring parameters (i.e. position angle and inclination) via chi-square minimization technique. We also discuss possible biases (e.g., resolution dependency) and its effect on our conclusions.

• 한국태양에너지학회 논문집
• /
• 제31권1호
• /
• pp.44-50
• /
• 2011

The solar radiation, inner temperature of the tilted box and the amount of condensed water were measured to find the most effective purified water production system. The inner temperature of the tilted box was related with solar radiation that was affected by sunshine and cloud. With analyzing those relationships of the solar radiation, inner box temperature, the angle of tilted boxes and amounts of water condensation optimal collecting system area could be calculated.