• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.2
• /
• pp.130-135
• /
• 2007

Wind tunnel test for Smart UAV power model has been conducted at KARI LSWT for about 3 months. The static model is used for the base plane and the power effect of tilt rotor is simulated by the tilt-rotor test rig installed in the test section. Although the genuine power effect is the difference between power-on and off tests. The existence of struts for power effect test produced unwanted form of interference and caused the change in flow angularity. To precisely evaluate power effect, a special approach is applied to Smart UAV test.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.15 no.4
• /
• pp.9-16
• /
• 2007

Tilt rotor aircraft can take off and land vertically and cruise faster than any other helicopter. A scaled flight demonstration model of a tilt rotor aircraft has been developed by KARI. Because the flight characteristics of tilt rotor are not well known, the developed scaled model would be helpful to evaluate flight control algorithm of a full scale aircraft. The tethered hover test has been performed in order to improve hover flight characteristics of tilt rotor aircraft prior to flight test of the small scaled model. During the tethered hover test, the performance of rotor speed governor, rate SAS (Stability Augmentation System) and control surface mixers have been evaluated. We expect that the results of real flight hover test would be quite same as tethered hover test. Therefore the tethered hover test results will reduce the risk of flight test properly by fixing some of hidden problems which might occur during the flight test. This paper presents the results of tethered hover test in detail and shows how it could be final ground test before flight test. The control mixer gain and rate SAS feedback gains were modified in order to get higher controllability and stability during the tethered hover flight. The rotor governor showed that it could keep rotor RPM constant with very small deviation even during severe pilot collective input change. The tethered hover test results gave pilot and engineers confirmation and experience about the scheduled flight test.

• Aerospace Engineering and Technology
• /
• v.12 no.1
• /
• pp.22-31
• /
• 2013

Flight tests on flight control performance of helicopter, conversion and airplane mode for the Smart UAV were completed. Automatic take-off and landing, automatic return home as well as automatic approach to hover were performed in helicopter mode. Climb/descent, left/right turn using speed and altitude hold mode were performed in each $10^{\circ}$ tilt angle in conversion mode. The rotor speed in airplane mode was reduced to 82% from 98% RPM in order to increase rotor efficiency with reducing Mach number at tip of rotors. It reached to the designed maximum speed, $V_{TAS}$=440 km/h at 3 km altitude. This paper presents the flight test result on full envelopment of Smart UAV. Detailed test plan and test data on control performance were also presented to prove that all data meets the flying qualities requirement.

• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.39-44
• /
• 2005

To validate the rotor performance analysis, 3D Computational Fluid Dynamics(CFD) analysis was performed for tilt rotor aeroacoustic model(TRAM). Also, 3D vehicle with rotating rotors was simulated for rotor power effect analysis. Multiple reference frame(MRF) and sliding mesh techniques were implemented to capture the effect of rotor revolution. CFD results were compared with the wind tunnel test results to validate their accuracy. At helicopter mode, CFD analysis predicted lower thrust than the wind tunnel test but CFD results showed good agreement with the test result at cruise mode. Rotor power effect decreased the lift but did not change drag and pitching moment.

• 한국전산유체공학회:학술대회논문집
• /
• 2007.04a
• /
• pp.8-13
• /
• 2007

Unsteady flow simulation for the tiltrotor Smart UAV configuration was performed to investigate the powered rotor wake effect on aerodynamic characteristics. Calculations were performed to simulate various flow conditions based on different flight modes including hover, conversion and cruise. Three-dimensional compressible Navier-Stokes equation code were used for flow calculation and Chimera grid technique overlapping individually generated grids was employed. A dynamic grid method was adopted in simulation of the rotating blades. Flow calculations were also conducted for the un-powered case. Aerodynamic interaction between the rotor and airframe was investigated comparing three data sets from the un-powered, powered, and isolated rotor cases.

• Aerospace Engineering and Technology
• /
• v.6 no.2
• /
• pp.236-244
• /
• 2007

The 40% scaled vehicle of Smart UAV has been developed for the investigation of basic flight characteristics and the verification of flight control algorithm. The similar gimbal hub and drive train with the full scale UAV were implemented and a forced air cooling reciprocating engine was installed. The various kind of tests were conducted for the major components of the vehicle. The important performance and mechanical endurance of the fabricated vehicle were identified by ground and hovering test.

• Aerospace Engineering and Technology
• /
• v.7 no.2
• /
• pp.31-37
• /
• 2008

Flight-test is necessary at the identification of dynamic model of flight vehicle. A commonly faced problem is that once the flight-test instrumentation system is difficult to reschedule in the vehicle at the end of the test. This paper identified the parameter of dynamic model of vehicle using measurement data of non-flight test. The identification algorithm is based on frequency response identification method (CIFER) dealing with a longitudinal motion of Smart UAV 40% scale.

• 한국항공운항학회:학술대회논문집
• /
• 2004.11a
• /
• pp.128-135
• /
• 2004

• 한국전산유체공학회:학술대회논문집
• /
• 2009.04a
• /
• pp.43-50
• /
• 2009

In order to reduce the download around Smart UAV(SUAV) at hovering and transition mode, flow control using synthetic jet has been performed. Many of the complex tilt rotor flow features are captured including wing leading and trailing edge separation, and the large region of separated flow beneath the wing. First, in order to control the trailing edge separation, synthetic jet is located at 30, 95% of flap chord length. The flow control using synthetic jet on flap shows that stall characteristics depending on several mode can be improved through separation vortices resizing. Also, a flap jet and a 0.01c jet which control the separation efficiently are applied at the same time at each test case because controlling the leading edge separation is essential for download reduction. As a result, time averaged download is reduced about 18% comparing with no control case at hovering mode and 48% at transition mode. These research results show that if flow control using leading edge jet and trailing edge jet is used effectively to the SUAV in overall flight mode, flight performance and stability can be improved.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.6
• /
• pp.63-69
• /
• 2011

The Smart UAV must have the control characteristics of propulsion system necessary for both rotary aircraft and fixed wing aircraft though it equips turbo-shaft engine. To develop an electronic engine controller in the future, it is necessary to accumulate the experience of engine operation and data of tilt rotor aircraft. For this purpose, the computer programs which predict engine performance in the steady state and transient state can be utilized for the supplementation of flight test data. In this work, we developed a dynamic analysis program using engine performance data gathered during the flight tests. In addition the accuracy of the program was verified through comparison with flight test data and the results of steady-state performance analysis program.