• 한국항공운항학회:학술대회논문집
• /
• 한국항공운항학회 2004년도 추계학술발표대회 논문집
• /
• pp.167-172
• /
• 2004

• 한국항공우주학회지
• /
• 제38권3호
• /
• pp.228-235
• /
• 2010

본 논문에서는 틸트로터 항공기의 회전익 모드에 대한 자율비행 유도제어 알고리즘을 적응제어기법을 이용하여 설계하는 것이다. 이를 위해 우선 출력기반 근사적 궤환선형화 기법을 통하여 알고리즘의 내부루프를 구성하고 그로부터 발생하는 모델오차를 단일 은닉층-신경망을 적용하여 상쇄하였다. 그리고 리아푸노프 안정성 이론에 따른 적응제어 갱신법칙은 선형 관측기를 기반으로 설계하였다. 나아가 외부루프는 경로점 유도법칙으로부터 생성되는 궤적을 추종하도록 하였으며 특히 엄밀한 자동착륙 궤적추종 성능 향상을 위하여 방향각 및 비행경로각 시선유도법칙을 설계하였다. 틸트로터 비선형 모델 시뮬레이션 결과는 콜렉티브 입력에서 보이는 순간적인 작동기 포화현상 이외에는 만족할 만한 안정성과 추종성능을 보여 주고 있다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.301-307
• /
• 2005

In this study, simplified whirl flutter analyses using quasisteady aerodynamic theory have been performed for a 2-DOF tilt-rotor system with both pitch and yaw motions of a rotor-nacelle. The present dynamic system consists of the rotor (propeller), forming the gyroscopic and aerodynamic element, supported horizontally by a pylon that is pivoted at some wing attachment point. Several design parameters (or rotor-nacelle system are considered and the effect of whirl flutter stability are also investigated for various design parameters.

• 항공우주시스템공학회지
• /
• 제3권3호
• /
• pp.17-23
• /
• 2009

KARI SUAV (Smart Unmanned Aerial Vehicle) program is currently on the phase of ground and flight test. SUAV is a tilt rotor aircraft having the capability of vertical take-off/landing and high speed forward flight. The SUAV rotor system is 3-bladed, gimbaled hub type, which is not common for conventional helicopter configuration. In this paper, detailed procedure and method of rotor pitch rigging, tracking and balancing were described based on the experience of SUAV ground test.

• Journal of Biosystems Engineering
• /
• 제35권4호
• /
• pp.215-223
• /
• 2010

In order to develop an precision aerial pesticide application system to be attached to an unmanned helicopter which can be applied to small lots of land, this study analyzed the flowing and spraying characteristics of the spray droplets by the main rotor downwash by setting the application conditions at the flight altitude of 3 m, the diameter of main rotor of 3.1 m, the boom length of around 2.8 m, and the spraying rate of 8 L/ha. The results of this study are summarized below. Through analysis of the covering area ratio of the spray droplets by main rotor downwash by nozzle type, boom with tilt angle and height, it was found that the covering area ratio of the twin flat-fan nozzle of around 25% was more uniform than other types of nozzle, also boom with $10^{\circ}$ tilt angle and spraying height of 3 m was shown to be the appropriate conditions for aerial application of pesticides. It was found that the nozzle position to minimize the scattering loss of spray droplets due to vortex phenomenon at both ends of the main rotor was around 10 cm from the end of the main rotor. An application test for the aerial pesticide application system attached to the HUA-ACEI unmanned helicopter developed by the Rural Development Administration showed that the range of covering area ratio of the spray droplets was 10-25%, and the spraying width was approximately 7 m when over 10% of covering area ratio was considered for valid spraying.

• Journal of Biosystems Engineering
• /
• 제35권5호
• /
• pp.302-309
• /
• 2010

Aerial application using an unmanned agricultural helicopter would allow precise and timely spraying. The attitude of a helicopter depends on a number of dynamic variables for roll-balanced flight. Laterally tilting behavior of a helicopter is a physically intrinsic phenomenon while hovering and forwarding. In order to balance the fuselage, the rotor should be counter-tilted, resulting in the biased down-wash. The biased spraying toward right side causes uneven spray pattern. In this study, a raised tail rotor system for the roll-balanced helicopter was studied. Thrust of the tail rotor system was measured and theoretically estimated for the fundamental database of the roll-balanced helicopter design. The estimated tail thrust and roll-moment would be used to design the raising height of tail rotor and roll balancing dynamics. The unmanned agricultural helicopter required the tail rotor thrust of about 39.2 N (4.0 kgf) during hovering with a payload of 235.4 N (24 kgf). A raised tail rotor system would compensate for the physical tilt phenomena. A further attitude control system of helicopter would assist roll-balanced aerial spray application.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2007년도 춘계 학술대회논문집
• /
• pp.8-13
• /
• 2007

Unsteady flow simulation for the tiltrotor Smart UAV configuration was performed to investigate the powered rotor wake effect on aerodynamic characteristics. Calculations were performed to simulate various flow conditions based on different flight modes including hover, conversion and cruise. Three-dimensional compressible Navier-Stokes equation code were used for flow calculation and Chimera grid technique overlapping individually generated grids was employed. A dynamic grid method was adopted in simulation of the rotating blades. Flow calculations were also conducted for the un-powered case. Aerodynamic interaction between the rotor and airframe was investigated comparing three data sets from the un-powered, powered, and isolated rotor cases.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 춘계학술발표대회 논문집
• /
• pp.79-82
• /
• 2004

The rotor drive system in rotor-craft carries out power transmission from powerplant to rotors and the drive shafts are fallen into misaligned condition by the vibration of engine and shafts and the deformation of supporting structures. The high performance flexible coupling accommodates these misalignments of drive shafts. In this study, we compare the performance of the metalic flexible coupling with the composite flexible coupling through analytic method to develop the high performance flexible coupling used in the rotor drive system of UAV tilt-rotor.

• 한국항공운항학회:학술대회논문집
• /
• 한국항공운항학회 2007년 춘계학술대회 논문집
• /
• pp.85-88
• /
• 2007

• 한국항공운항학회지
• /
• 제15권4호
• /
• pp.24-32
• /
• 2007

In this study, computational structural vibration analyses of a smart unmanned aerial vehicle (SUAV) with tilt-rotors due to dynamic hub loads have been conducted considering detailed supporting structures of installed equipments. Three-dimensional dynamic finite element model has been constructed for different fuel conditions and tilting angles corresponding to helicopter, transition and airplane flight modes. Practical computational procedure for modal transient response analysis is successfully established. Also, dynamic loads generated by rotating blades and wakes in the transient and forward flight conditions are calculated by unsteady computational fluid dynamics technique with sliding mesh concept. As the results of present study, transient structural displacements and accelerations of the vibration sensitive equipments are presented in detail. In addition, vibration characteristics of structures and installed equipments of which safe operation is normally limited by the vibration environment specifications are physically investigated for different flight conditions.