• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.279-279
• /
• 2010

한국형 헬륨 냉각 고체형 증식(Helium Cooled Solid Breeder : HCSB) 시험 블랑켓(Test Blanket Module : TBM)은 삼중수소 증식을 위해서 $Li_2TiO_3$ 및 $Li_4SiO_4$ 페블을 고려하고 있으며, 중성자 반사 재료로는 SiC가 코팅된 흑연 페블을 사용할 예정이다. $Li_2TiO_3$ 및 $Li_4SiO_4$ 페블을 제조하기 위해서는 먼저 각각의 분말 제조가 선행되어야 한다. $Li_2TiO_3$ 분말을 합성하기 위해서는 먼저 Lithium 금속염과 Isopropoxide를 용매 및 폴리머 캐리어로서의 두 가지 기능을 하는 에틸렌글리콜에 첨가한 후 가열하여 완전히 용해시킨 후 혼합 용액을 건조시켜 겔형의 전구체를 제조한다. 이를 하소한 후 결정화시켜 Titanate 분말을 얻는데 이때의 건조, 하소 및 결정화 온도의 조건에 따른 분말의 크기 및 특성이 각각 다르다. 즉 하소 온도가 $600^{\circ}C$ 미만이면 열분해된 폴리머로부터 잔유 탄소가 남게 되고, $700^{\circ}C$를 초과하면 결정화가 시작된다. 이렇게 얻어진 Titanate분말은 지르코니아 볼을 이용하여 약 24 시간 동안 볼 밀링 과정을 통해 입도분포가 좁은 미세한 Titanate 분말로 만들었다. $Li_2TiO_3$ 페블은 위의 과정에서 얻어진 미세분말에 바인더를 이용하여 페블화 시킨 후 $1200^{\circ}C$의 전기로에서 최종 소결한 것이다. 중성자 반사 재료인 흑연페블은 강도가 약하기 때문에 표면에 SiC를 수 ${\mu}m$ 코팅해서 사용할 예정이다. 선행실험으로 건식법을 이용하여 SiC 코팅을 실시했으며, 그 결과를 소개할 것이다.

• Journal of Powder Materials
• /
• v.12 no.4 s.51
• /
• pp.249-254
• /
• 2005

Titanium dioxide was prepared by Polymer Complex Solution Method(PCSM) according to the mole ratio of Titanium (IV) isopropoxide(TTIP)/solvent and polymer(Poly Ethylene Glycol). Polymer electrolytes were usually made by dispersing preproduced ceramic nanoparticles in a polymer matrix. Using this method, pure and nano-sized $TiO_2$ powder was synthesized through a simple procedure and polymer entrapment route. At the optimum amount of the polymer, the titanium ions are dispersed in solution and a homogeneous polymeric network is formed. The maximum intensity of anatase phase of $TiO_2$ was achieved by calcining at $500^{\circ}C$ for 2h. The synthesized $TiO_2$ powders were nano-sized and the average size was about 50nm. Anatase/Rutile ratio of the synthesized $TiO_2$ was 70%/30%.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2004.04a
• /
• pp.31-31
• /
• 2004

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2005.11a
• /
• pp.18-20
• /
• 2005

• Journal of Powder Materials
• /
• v.12 no.5 s.52
• /
• pp.336-344
• /
• 2005

In the present study, the focus is on the effect of cobalt oxide powder in the carbothermal reduction of the titanium-cobalt-oxygen based oxide powder by solid carbon for the optimizing synthesis process of ultra fine TiC/Co composite powder. The titanium-cobalt-oxygen based oxide powder was prepared by the combination of the spray drying and desalting processes using the titanium dioxide powder and cobalt nitrate as the raw materials. The titanium-cobalt-oxygen based oxide powder was mixed with carbon black, and then this mixture was carbothermally reduced under flowing argon atmosphere. Changes in the phase structure and thermal gravity of the mixture during carbothermal reduction were analysed using XRD and TGA. Titanium-cobalt-oxygen based oxide powder desalted at $600^{\circ}C$ had a mixture of $TiO_2\;and\;Co_{3}O_4$. And the one desalted at $800^{\circ}C$ had a mixture of $TiO_2\;and\;CoTiO_3$. In the case of the former powder, the reduction of cobalt oxide powder in the titanium-cobalt-oxygen based oxide powder occurred at lower temperature than the latter one. However, the carbothermal reduction of titanium dioxide powder in the titanium-cobalt-oxygen based oxide powder with a mixture of $TiO_2\;and\;Co_{3}O_4$ occurred at higher temperature than the one with a mixture of $TiO_2\;and\;CoTiO_3$. And also, the former powder showed a lower TiC formation ability than the latter one.

• Journal of Powder Materials
• /
• v.29 no.5
• /
• pp.357-362
• /
• 2022

The low-temperature sinterability of TiO₂-CuO systems was investigated using a solid solution of SnO₂. Sample powders were prepared through conventional ball milling of mixed raw powders. With the SnO₂ content, the compositions of the samples were Ti_1-xSn_xO₂-CuO(2 wt.%) in the range of x ≤ 0.08. Compared with the samples without SnO₂ addition, the densification was enhanced when the samples were sintered at 900℃. The dominant mass transport mechanism seemed to be grain-boundary diffusion during heat treatment at 900℃, where active grain-boundary diffusion was responsible for the improved densification. The rapid grain growth featured by activated sintering was also obstructed with the addition of SnO₂. This suggested that both CuO as an activator and SnO₂ dopant synergistically reduced the sintering temperature of TiO₂.

• Journal of Powder Materials
• /
• v.6 no.1
• /
• pp.75-80
• /
• 1999

The formation of $n-TiO_2$ powder by oxidation of Ti-ethoxied vapor in a flat flame burner reactor maintained under 20 torr has been studied. The produced powder were characterized in terms of crystal structure, chemical composition by XRD and TEM. The results showed that the powder consisted of loose agglomerated anatase and rutile particles and their size were about 10 nm and 20 nm, respectively. In the course of synthesis, changes of the flame color were happened to each condition during heating up the bubbler. The flame color transition phenomena reveled that a critical precursor delivery rate was needed for the powder formation (obtainable powder yield). The critical precursor delivery rate was estimated by a simple function of the bubbler temperature and the carrier gas flow rate. The critical precursor delivery rate was reviewed as an important variable of the nanopowder synthesis.

• Journal of the Mineralogical Society of Korea
• /
• v.15 no.1
• /
• pp.59-68
• /
• 2002

Chemical analyses and Rietveld structural refinement with powder X-ray diffraction data were done for Nb-rich perovskite, named latrappite ($Ca_2NbFe^{3+}O_6$)from the Oka, Quebec, Canada. Latrappite is shown to be a member of a continuous solid solution of $CaTiO_3-NaNbO_3-Ca_2NbFe^{3+}O_6$ and approximately $(Ca_{1.5}Na_{0.4})\;(Nb_{0.1}Ti_{0.6}Fe_{0.4})O_6$ in composition. The crystal structure of latrappite, determined by Rietveld refinement, is similar to that of perovskite ($CaTiO_3$). It differs in that replacement of Ti by Nb and $Fe^{3+}$ results in greater distortion and tilting of the $TiO_6$ framework octahedra relative to $CaTiO_3$. Revised unit-cell parameters of latrappite are a=5.4474(4), b=5.5264(4), c=7.7519(5) ${\AA},\;V=233.4(3){\AA}^3$ space group Pbnm.

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.1
• /
• pp.15-19
• /
• 2013

The n-type $Bi_2(Te_{0.9}Se_{0.1})_3$ powders, which were fabricated by melting/grinding method and dispersed with 0.5 vol% $TiO_2$ nanopowders, were hot-pressed in order to investigate the effects of $TiO_2$ dispersion on the thermoelectric properties of the hot-pressed $Bi_2(Te_{0.9}Se_{0.1})_3$. Excellent thermoelectric properties such as a maximum figure-of-merit of $2.93{\times}10^{-3}/K$ and a maximum dimensionless figure-of-merit of 1.02 were obtained for the hot-pressed $Bi_2(Te_{0.9}Se_{0.1})_3$. With dispersion of 0.5 vol% $TiO_2$ nanopowders, the maximum figure-of-merit and the maximum dimensionless figure-of-merit decreased to $2.09{\times}10^{-3}/K$ and 0.68, respectively.

• Journal of Powder Materials
• /
• v.10 no.4
• /
• pp.228-234
• /
• 2003

In the present study, the focus is on the synthesis of titanium carbide/cobalt composite powder by the spray thermal conversion process using metallic salt solution as the raw materials. Two types of oxide powders of Ti-Co-O system were prepared by the spray drying of two types of metallic salt solutions : titanium chloride-cobalt nitrate and $TiO_2$ powder-cobalt nitrate solutions. These oxide powders were mixed with carbon black, and then these mixtures were carbothermal reduced under a flowing argon atmosphere. The changes in the phase structure and thermal gravity of the mixtures during carbothermal reduction were analysed using XRD and TG-DTA. In the case of using the titanium chloride-cobalt nitrate solution, it could not be obtained TiC/Co composite powder due to contamination of the impurities during the spray drying of the solution. However, in tile case of using the $TiO_2$ powder-cobalt nitrate scullion, TiC-15 wt. %Co composite powder could be synthesized by the spray thermal conversion process. The synthesized TiC-15 wt. %Co composite powder at 120$0^{\circ}C$ for 2 hours has average particle size of 150 nm.