• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.437-440
• /
• 1999

The objective of this study is to deposited the preparation of SrTiO$_3$dielectric thin films on Ag/barrier-mater/Si(N-type 100) bottom electrode using a conventional rf-magnetron sputtering technique with a ceramic target under various conditions. It is demonstrated that the leakage current of films are strongly dependent on the substrate temperature. The current-voltage characteristics are influenced by the Schottky effict. The resistivity properties of films deposited on silicon substrates were very high resistivity. Conduction mechanisms in the films was dependent on the substrate temperature range.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.244-247
• /
• 1999

The(Sr$\sub$0.85/Ca$\sub$0.15/) TiO$_3$(SCT) thin films are deposited on Pt-coated electrode(Pt/TiN/SiO$_2$/Si) using RF sputtering method. The composition of SCT thin films deposited on Si substrate at room temperature is close to stoichiometry(1.102 in A/B ratio). Also, SCT thin films deposited on Pt-coated electrodes have the cubic perovskite structure and polycrystalline state. The maximum dielectric constant of SCT thin films is obtained by annealing at 600[$^{\circ}C$].The dielectric constant changes almost linearly in temperature ranges of -80~+90[$^{\circ}C$].

• Journal of Sensor Science and Technology
• /
• v.19 no.3
• /
• pp.202-208
• /
• 2010

This study examined the dependency of crystalline orientation and electric properties of sol-gel PZT film on hydrolysis, a $PbTiO_3$ seed layer and a concentration of sol-gel solution. The PZT thin films were prepared by using 2-Methoxyethanol-based sol-gel method and spin-coating on Pt/Ti/$SiO_2$/Si substrates. The 1-${\mu}m$-thick PZT films were coated and then fired in a furnace by direct insert method. The highly (111) oriented PZT film of pure perovskite structure could be obtained. We could control the degree of orientation by various parameters such as hydrolysis, a $PbTiO_3$ seed layer and a concentration of sol-gel solution. The highest measured remanent polarization, dielectric constant and piezoelectric coefficient are $24.16\;{\mu}C/cm^2$, 2808, and 159 pC/N, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.191-191
• /
• 2009

$Bi_4Ti_3O_{12}$ (BiT) thin films were well developed on the Pt/Ti/$SiO_2/Si$ substrate by a metal organic decomposition (MOD) method. Oxygen was effective on the crystallization of the BiT thin films during a rapid thermal annealing process. The electrical properties of the BiT films dependant on the oxygen partial pressure were investigated. No crystalline phase was observed for the BiT film annealed at $700^{\circ}C$ under oxygen free atmosphere. However, its crystallinity was significantly evolutionned with increasing oxygen partial pressure. In addition, its dielectric and piezoelectric properties were enhanced with increasing oxygen partial pressure to 10 torr. Especially, the BiT film, annealed at $700^{\circ}C$ and 10 torr oxygen pressure, showed good dielectric properties: dielectric constant of 51 and dielectric loss of 0.2 % at 100 kHz. Its leakage current and piezoelectric constant ($d_{33}$) was also considerably improved, being as 0.62 nA/$cm^2$ at 1 V and approximately 51 pm/V, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.4
• /
• pp.290-296
• /
• 2009

$Bi_{4}Ti_{3}O_{12}$ (BiT) thin films were grown on the Pt/Ti/$SiO_2$/si substrate using a metal organic decomposition (MOD) method. Effects of oxygen annealing on the structural properties and dielectric properties of the BiT thin films were investigated. The BiT films were well developed when rapid thermal annealed at $>500^{\circ}C$ in oxygen ambient. For the film annealed at $700^{\circ}C$, no crystalline phase was observed under oxygen free annealing atmosphere while its crystallinity was significantly enhanced as the oxygen pressure increased. The BiT film also exhibited a smooth surface with defect free grains. A high dielectric constant and a low dielectric loss were achieved satisfactory in the frequency range from 75 kHz to 1 MHz. Especially, the BiT film, annealed at $700^{\circ}C$ and 10 torr oxygen pressure, showed good dielectric properties: dielectric constant of 51 and dielectric loss of 0.2 % at 100 kHz. Its leakage current was also considerably improved, being as $0.62\;nA/cm^2$ at 1 V. Therefore, it is considered that the oxygen annealing has effects on an enhancement of crystallinity and dielectric properties of the BiT films.

• Journal of the Korean Vacuum Society
• /
• v.4 no.S1
• /
• pp.81-86
• /
• 1995

Aluminum has been deposited selectively on TiN surfaces in the presence of Si, SiO2 from Dimethyethylamine Alane(DMEAA). The film properties of the deopsited AI film were determined by various methods(SEM, Auger, UV-photospectrometer, Four point-probe, XRD). The effect of in-situ H2 plasma precleaning was studied. The effect of gap distance, pressure and temperature on the properties(crystallinity, resistance, grain size, morphology) of AI film and on the growth rates was investigated. It was found that the plasma precleaning promotes the growth rate and there exists optimum thmperature for maximum growth rate.

• Journal of the Korean Magnetics Society
• /
• v.11 no.5
• /
• pp.222-225
• /
• 2001

The planar type inductors have a good potential for the application of miniaturized low power DC-DC converters. For those high quality application, the reduction of coil loss and also magnetic films which have good high frequency properties are required. Fabricated inductor was consisted of FeTaN/Ti magnetic film and electroplated Cu coil thickness of 100$\mu\textrm{m}$ and $SiO_2$ as a insulating layer. The inductor was designed double rectangular spiral shape for magnetic field highly confining within the device. The measured value of inductance and resistance were 980 nH and 1.7 $\Omega$ at 1 MHz as operating frequency of device. The Q factor is 3.55 at 1 MHz.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.5
• /
• pp.801-804
• /
• 2006

[ $GdAlO_3(GAO)$ ] buffer layer for $YBa_2Cu_3O_{7-{\delta}}(YBCO)$ coated superconductor wire was fabricated by sol-gel processing. Precursor solution was prepared by dissolving 1:1 stoichiometric quantaties of gadolinium nitrate hexahydrate and aluminum nitrate nonahydrate in methanol. The solution was spin-coated on $SrTiO_3(STO)$(100) single crystal substrates and heated at $1000^{\circ}C$ for 2h in wet $N_2-5%\; H_2$, atmosphere. A SEM(scanning electron microscopy) observation of the surface morphology of the GAO layer has shown that it has a faceted morphology indicating epitaxy. It was shown from x-ray diffraction(XRB) that GAO buffer layer was highly c-axis oriented epitaxial thin film with both good out-of-plane($FWHM=0.29^{\circ}$ for the (002) reflection) and in-plane ($FWHM=1.10^{\circ}$ for the {112} reflection) alignment.

• Korean Journal of Materials Research
• /
• v.8 no.2
• /
• pp.131-134
• /
• 1998

The deposition rate and surface morphology of Al films deposited by MOCVD have been studied on the $SiO_{2}$ and TiN(60nm/Si) substrates. A1 films were deposited with the pyrolysis of dimethylethylamine alane(DMEAA). When A1 was deposited on Ti& substrate without carrier gas, Al deposition rate increased with H\ulcorner pre- treatment. The $H_2$ gas enhances the CVD reaction at the substrate surface. When Al was deposited on $SiO_{2}$ substrate, $H_2$ plasma pretreatment reduced Al incubation time and made a dense Al film compared with Ar plasma pre- treatment or no pretreatment.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1997.07a
• /
• pp.114-114
• /
• 1997