• 한국해양공학회지
• /
• 제28권4호
• /
• pp.338-344
• /
• 2014

The purpose of this study was to evaluate the dispersion degree of particles using a nanoindentation test for titanium oxide nanoparticles/epoxy resin nanocomposites. Thus, the effects of the particle size and weight fraction, dispersion agent, and position of the sample on the modulus and degree of particle dispersion in the nanocomposites were investigated. As a result, the dispersion degree of large particles was found to be better than that of smaller particles in composites. It could be found that the aggregation or agglomeration of small particles with large surface energy occurred more easily in nanocomposites because of the large specific surface area. The moduli of the upper side of the film-shaped sample obtained from a nanoindentation test were low scattering, while the values for the bottom side were high scattering. Thus, the dispersion situation of the nanoparticles on the upper side of film-shaped samples could be considered to be better than that for the bottom side. This could be concluded due to the non-uniform nanoparticle dispersion in the same sample. The modulus obtained from nanoindentation test increased slightly with the content of nanoparticles and increased with the indented depth for the same sample. The latter is presumably due to the increase in the accumulated particles facing the indenter with the indented depth. The nanoindentation test was found to be a useful method to evaluate the dispersion status of nanoparticles in nanocomposites.

• Transactions on Electrical and Electronic Materials
• /
• 제6권5호
• /
• pp.238-242
• /
• 2005

The Pt counter electrode of a dye-sensitized solar cell (DSSC) plays a role in helping redox reaction of iodine ions in electrolyte, also, transferring electrons into electrolyte. In this case, it is expected that characteristics of Pt electrodes strongly depend on fabrication process and its surface condition. In this study, Pt electrodes were prepared by a electro-deposition and a RF magnetron sputtering. Electrochemical behavior of Pt electrodes was compared using cyclic-voltammetry and impedance spectroscopy. Surface morphology of Pt electrodes was investigated by FE-SEM and AFM. I-V characteristics of DSSC were measured and discussed in association with the surface properties of counter electrode. As a result, electrochemical properties of electro-deposited Pt electrode were superior to that of sputtered Pt electrode. This is likely that enlarged area of surface in electro-deposited Pt electrode in comparison with the case of sputtered Pt electrode playa role in enhancing such electrochemical properties.

• 한국전기전자재료학회논문지
• /
• 제18권1호
• /
• pp.43-49
• /
• 2005

Temperature stabilities of resonance frequencies of the substrates are very important in piezoelectric ceramics oscillators and fitters. In this study, it was investigated thermal resisting property of the length-extensional vibration mode of PZT ceramics. The mode can be utilized in fabricating ultra-small 55 kHz IF devices. We fabricated the ceramic specimens with x = 0.51, 0.52, 0.53, 0.54, and 0.55 in the Pb(Zr$\sub$x/Ti$\sub$1-x/)O$_3$ system. And their resonance frequencies were measured before 1st thermal aging, after 1st and 2nd thermal aging. In order to investigate the influence of thermal aging on thermal resisting properties, thermally aged specimens were once mote thermally aged. Before 1st thermal aging, the specimens of the compositions with morphotropic phase, x = 0.53 and rhombohedral phase, x = 0.54 have weak thermal resisting property of resonance frequency, while tetragonal phase, x = 0.51 has robust thermal resisting property of resonance frequency. 1st thermal aging improved thermal resisting property of resonance frequency in all specimens.

• 동력기계공학회지
• /
• 제17권5호
• /
• pp.69-77
• /
• 2013

The purpose of this study is to improve the properties of epoxy resin using the big-sized titanium oxide nanoparticles. The effects of particle weight fraction and shape of sample on the thermal and mechanical properties in titanium oxide reinforced epoxy resin has been investigated. In addition, the effect of particle dispersion situation on the mechanical properties of nanocomposites has been studied. As a result, the Tg was almost same regardless of the content of nanoparticles. Storage modulus increased up to the content of 3wt% particles and then decreased. Tensile strength and modulus of film-shaped sample with 1wt% was higher than the one of pure epoxy, while other composites were not. The tensile strength of dogbone-shaped sample with 1wt% was only higher than the one of pure epoxy, while other composites were lower than the one of pure epoxy. Tensile modulus of dogbone-shaped samples increased with the content of particles.

• 한국통신학회논문지
• /
• 제17권2호
• /
• pp.121-131
• /
• 1992

포스트 필터링(adaptive postfiltering)을 수신단의 마지막에세 수행 하였다. 첫째는, SBC 시스템의 대역 필터를 QMF(Quadrature Mirror Filter) 대신 GQMF(Generalized QMF)를 사용하여 성능을 향상시켰고, 둘째는, 각 대역에 적응 비트 할당을 함으로써 음질의 향상뿐 아니라 variable rate 부호화할 수도 있었다. 세번째로는 APCM(Adaptive Plulse Code Modulation)과 ADPCM(Adaptive Differential Pulse Code Modulation)을 부호화기로 사용하여 각각의 성능을 평가 한 결과, SB-APCM 의 성능이 우수하였다.또한, 수신단의 마지막에서 적응 포스트 필터링을 수행하여 부호화된 음성의 음질을 개선할 수 있었다. 본 논문에서는 두가지의 적응 포스트 필터링 기법을 제안하였는데 낮은 복잡성을 가지고도 부호화된 음성에서 상당량의 잡음 감쇄를 이룰 수 있었다.

• Nuclear Engineering and Technology
• /
• 제52권10호
• /
• pp.2353-2360
• /
• 2020

An anodic electrophoretic deposition (EPD) technique is used to create a uniform TiO₂ thin film coating on boiling thin steel plates (1.1 mm by 90 mm). All of the effective parameters except time of the EPD method are kept constant. To investigate the effect of gamma irradiation on the critical heat flux (CHF), the test specimens were irradiated in a gamma cell to different doses ranging from 100 to 300 kGy, and then SEM and BET analysis were performed. For each coated specimen, the contact angle and capillary length were measured. The specimens were then tested in a boiling pool for CHF and boiling heat transfer coefficient. It was observed that irradiation significantly decreases the maximum pore diameter while it increases the porosity, pore surface area and pore volume. These surface modifications due to gamma irradiation increased the CHF of the nano-coated surfaces compared to that of the unirradiated surfaces. The heat transfer coefficient (HTC) of the nano-coated surfaces irradiated at 300 kGy increased from 83 to 160 kW/(㎡ K) at 885 kW/㎡ wall heat flux by 100%. The CHF of the irradiated (300 kGy) and unirradiated surfaces are 2035 kW/㎡ and 1583 kW/㎡, respectively, an increase of nearly 31%.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.885-888
• /
• 2000

The effects of deposition temperature and post annealing process of ferroelectric PbZr$\sub$0.52/Ti$\sub$0.48/O$_3$(PZT) thin films by pulsed laser deposition (PLD) were investigated. The PZT thin films were deposited at 400, 450, 500, and 550$^{\circ}C$, with/without post annealing at 650$^{\circ}C$ for 30 min. The PZT thin films deposited above 500$^{\circ}C$ without post annealing were crystallized into peroveskite phase, but the PZT thin films deposited below 450$^{\circ}C$ had pyrochlore phase. The PZT thin films deposited below 450$^{\circ}C$ with post annealing also crystallized into pure perovskite. Compared to the PZT thin films which were deposited at 450$^{\circ}C$ and post annealed, the films deposited at 550$^{\circ}C$ have a columnar microstructure and high remnant polarization 28 (${\mu}$C/cm$^2$). With in-situ annealing at oxygen ambient, the PZT thin films reduced oxygen vacancies and increased retained polarization.

• 보존과학회지
• /
• 제37권1호
• /
• pp.34-42
• /
• 2021

This study analyzes six slags excavated from the iron making site in Gogi-ri, Namwon, Korea to understand the characteristics of the ruins, and to confirm the iron making process performed at the time. The chemical components of the iron making by-products from the Gogi-ri site were analyzed, and the findings indicate total Fe contents between 23.24% and 37.56%, which are lower than the typical total Fe content found in ancient iron making processes. The deoxidation agent contents of the slags ranged from 43.88% to 58.13%, which are higher than the typical deoxidation agent content of ancient iron making processes. The high content suggests smooth separation between iron and slags, and TiO₂ detected from the site suggests the use of materials with high titanium content in the iron making in the region. As for the microstructures of the slags, some slags have long pillar-shaped fayalites, while others have pillar-shaped wüstite along with ulvöspinel. Slags from the forging furnace show hammer scales created by both the earlier stages and later stages of forging work. The findings suggest that the iron making site in Gogi-ri, Namwon, Korea used to be an iron making facility where a full range of iron making process was carried out ranging from smelting to forging, and the ironmakers used a wide array of technologies to manufacture iron products.

• Current Optics and Photonics
• /
• 제6권1호
• /
• pp.79-85
• /
• 2022

Tracers are one of the critical factors for improving the performance of velocimetry. Silver and gold nanoparticles as tracers with localized surface-plasmon resonance are analyzed for their scattering properties. The scattering cross sections, angular distribution of the scattering, and equivalent scattering cross sections from 53° and 1.5° half-angle cones at 532 nm are calculated, with particle sizes in the nanoscale range. The 53° and 1.5° half-angle cones used as examples correspond respectively to the collection cones for microscope objectives in microscopic measurements and camera lenses in macroscopic measurements. We find that there is a transitional size near 35 nm when comparing the equivalent scattering cross sections between silver and gold nanoparticles in water at 532 nm. The equivalent scattering cross section of silver nanoparticles is greater or smaller than that of gold nanoparticles when the particle radius is greater or smaller than 35 nm respectively. When the radius of the plasmonic nanoparticles is smaller than about 44 nm, their equivalent scattering cross sections are at least ten times that of TiO₂ nanoparticles. Plasmonic nanoparticles are promising for velocimetry applications.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 봄 학술논문 발표대회
• /
• pp.93-94
• /
• 2023

Through the industrial revolution that began in the 18th century, the amount of carbon dioxide in the atmosphere increased rapidly as humans used fossil energy such as coal and oil as fuel for steam engines and factory machines. The amount of carbon dioxide emitted while producing cement, the main material of concrete used in construction, is large enough to account for 5-8% of the world's carbon dioxide emissions. In this study, Non cement-based matrix were used to reduce carbon dioxide emissions from cement production. Red mud is an industrial by-product generated in the manufacturing process of aluminum hydroxide using bauxite, and more than 120 million tons are produced worldwide. In addition, red mud is a porous material that can be physically adsorbed, and causes a photocatalytic reaction of TiO₂ to remove harmful substances such as nitrogen oxide formaldehyde in the air and chemically adsorbs ammonia and hydrogen sulfide. Therefore, this study aims to examine the physical properties of the matrix by mixing red mud, an industrial by-product with good adsorption performance, into the Non cement-based matrix.