• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1025-1025
• /
• 2006

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1026-1029
• /
• 2006

Particulate reinforced titanium composites were produced by PM rout. Differents volumetric percentages of TiN reinforcements were used, 5,10,15 vol%. Samples were uniaxial pressed and vacuum sintered at differents temperatures between $1200-1300^{\circ}C$. Density, porosity, shrinkage, mechanical properties and microstructure were studied. Elastic properties and strength resistance were analysed by flexural strength and tension tests, and after the test, fractured samples were analysed too, obtaining a correlation between the fracture, interparticulated or intraparticulated, and the reinforcement addition.. Hardness and microhardness test were applied too, in order to complete the study about mechanical properties. In order to study wear resistance pin-on-disc test were used. In addition, the temperature influence, the reactivity between matrix and reinforcement, and the microstructures developed were observed by optical and electron microscopy.

• 한국분말재료학회지
• /
• 제17권2호
• /
• pp.123-129
• /
• 2010

The fabrication of interconnect from titanium powders and $TiN_x$ powders is investigated. Corrosion-resistant titanium and $TiN_x$ are used as reinforcement in order to reveal high heat and corrosion resistance at the elevated temperature. We fabricated the plates for interconnect reinforced with $TiN_x$ by mixing titanium powders with 10 wt.% of nano-sized $TiN_x$. Spark Plasma Sintering (SPS) was chosen for the sintering of these composites. The plate made of titanium powders and $TiN_x$ powders demonstrates higher corrosion resistance than that of the plate of titanium powders alone. The physical properties of specimens were analyzed by performing hardness test and biaxial strength test. The electrochemical properties, such as corrosion resistance and hydrogen permeability at high temperature, were also investigated. The microstructures of the specimens were investigated by FESEM and profiles of chemical compositions were analyzed by EDX.

• 대한금속재료학회지
• /
• 제48권11호
• /
• pp.1003-1008
• /
• 2010

In this study, the effect of the reinforcement on the wear behaviour and mechanical properties of hypereutectic Al-Si alloys was investigated. The Gas atomized hypereutectic Al-20Si alloy powders were mixed with 1, 3, and 5 wt.% AlN and TiC ceramic particles and consolidated by hotpress. The Al-20Si powder has both finely dispersed primary Si phases and eutectic structures. The Al-20Si-AlN, TiC composites showed that the reinforcements were distributed along the boundary of the Al-20Si alloy. The UTS increased with increasing the AlN, TiC contents. At a lower load, with an increasing weight fraction of reinforcements, the wear rate decreased in both composites and the wear mechanism was adhesive wear. At a higher load, the shape of the debris changes the mechanism of the AlN composites to abrasive-adhesion wear and this resulted in an increase of the wear rate.

• 소성∙가공
• /
• 제8권3호
• /
• pp.259-259
• /
• 1999

TiC ceramic particulate-reinforced titanium matrix composites were fabricated and the resultant densification, microstructure, and static and dynamic mechanical properties were studied. Comparing Ti with TiH₂powders as host materials for TiC ceramic reinforcement by pressureless vacuum sintering, TiH₂-started composites showed better sinterability and resistance to both elastic and plastic deformation than Ti-started ones. When TiH₂and TiH₂-45 vol.%TiC samples were hot pressed, TiH₂matrices transformed to alpha prime Ti and alpha Ti phase, respectively. It is interpreted that the diffusion of an alpha stabilizer carbon from TiC into the matrix is one of the plausible reasons far such a microstructural difference. The 0.2% offset yield strengths of the hot pressed TiH₂and TiH₂-45 vol.%TiC samples were 1008 and 1446 MPa, respectively, in a static compressive mode (strain rate of 1×$10^{-3}$/s). Dynamic compressive strengths of the samples were 1600 and 2060 MPa, respectively, at a strain rate of 4×10³/s.

• 한국결정성장학회지
• /
• 제29권6호
• /
• pp.329-337
• /
• 2019

스플린터(splinter) 및 판상(plate shape) 형상을 가지는 티탄산칼륨염(K₂O·nTiO₂, PT)을 합성하고 브레이크 마찰재의 보강재로 이용하여 마찰 특성을 평가하였다. 스플린터형 티탄산칼륨염을 합성하기 위하여 먼저 판상 형상을 가지는 사티탄산칼륨염(K₂O·4TiO₂, PT4)을 합성하고 칼륨 이온(K⁺)을 일부 산침출(acid leaching)하여 육티탄산칼륨염(K₂O·6TiO₂, PT6)으로 변환시킨 후, 800℃에서 열처리하여 스플린터 형상의 입자를 얻었다. 판상형 티탄산칼륨염을 합성하기 위해서 염화칼륨을 융제로 사용하고 마그네슘(Mg)을 일부 첨가하여 판상의 형상을 가지는 마그네슘티탄산칼륨염(K_0.8Mg_0.4Ti_1.6O₄, PMT)을 합성하였다. 얻어진 육티탄산칼륨염 및 마그네슘티탄산칼륨염 입자를 보강재로 이용하여 브레이크 패드 마찰재를 제작하고 1/ 5-스케일 다이나모미터(scale dynamometer)를 이용하여 마찰 마모 특성을 평가하였다. 평가 결과, 두 종류의 보강재가 유사한 마찰계수 및 Fade & recovery 특성을 보였으며 판상형 마그네슘티탄산칼륨염의 경우, 스플린터형 육티탄산칼륨염보다 우수한 내마모성을 보이는 것을 알 수 있었다.