• The Korean Journal of Ceramics
• /
• v.6 no.3
• /
• pp.309-314
• /
• 2000

In the present study, preliminary experimental results of the change in the properties of perovskite-type oxides caused by the $^{18}O$- exchange have been reported. Two systems were selected for the exchange, (1) $ATiO_3$(A=Ca,Sr,Ba) and (2) manganese perovskite. The dielectric properties of isotope-exchanged $SrTi^{18}O_3$showed a drastic change from a quantum paraelectricity below 3K to ferroelectric-like behavior with a peak at 23K and an enhanced dielectric constant, 35000 at the peak. On the contrary, the $T_c$ for $BaTiO_3$was found to increase by 0.9K. The observed isotope shift of $T_c$ as well as $T_co$ for the manganese perovskites is correlated with the key parameters controlling the lattice such as $Mn^{3+}$ content, average ionic radius of the A-site cation <$r_A$> ad A-site ionic disorder $\sigma^2$.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.822-823
• /
• 2006

The compaction and sintering behavior of zirconium titanate $(ZrTiO_4)$ was investigated by means of the measurement of sintering density and shrinkage, and the observation of microstructure. With increasing the content of $Al_2O_3$ additive, $Al_2O_3$-modified zirconium titanate samples fired at $1300^{\circ}C$ showed the anisotropic shrinkage behavior that the upper region of sintered body has higher sintering shrinkage than the low region. This difference of sintering shrinkage decreased with increasing firing temperature from 1300 to $1400^{\circ}C$. The SEM micrographs of powder compation show that the anisotropic shrinkage behavior is related with non-uniform density in a uniaxial compaction.

• Electrical & Electronic Materials
• /
• v.9 no.7
• /
• pp.668-673
• /
• 1996

In this paper, (P $b_{1-x}$ L $a_{x}$)(Z $r_{0.52}$ $Ti_{0.48}$) $O_{3}$ (X=0-13[at%]) thin film were prepared by the Sol-Gel method, Multiple PLZT thin films were spin-coated on the Pt/Ti/ $SiO_{2}$Si substrate. The electrical properties of the films were investigated for varying the annealing temperature. In the PLZT(11/52/48) specimens, the dielectric ocnstant of 1236 and the polarization reversal time of 460[nm] were obtained and the breakdown of the film did not occur up to 1*10$^{10}$ cycles at the voltage of 7[V] by the bipolar acceleration. The remanent polarization and coercive field decreased with increasing the content of La in the range of 0-13[at%] and thin film of the PLZT(11/52/48) showed the value of 2.56[.mu.C/c $m^{2}$] and 21.1[kV/cm], respectively.ly.y.

• Journal of Powder Materials
• /
• v.6 no.1
• /
• pp.88-95
• /
• 1999

The purpose of this study is to investigate the manufacturing feasibility of WC-Co milling inserts via Powder Injection Molding (PIM) process. WC-Co is used in a wide variety of cutting tools due to its high hardness, stiffness, compressive strength and wear resistance properties. WC-Co parts for a high stress application were conventionally produced by the press and sinter method, which were Iimited to 2 dimensional shapes. Manufacturing WC-Co parts for a high stress application by PIM implies that tool efficiency can be highly improved due to increased freedom is design. P30 grade WC powder (WC-Co-TiC-TaC system) was mixed with RIST-5B133 binder and injection molded into milling inserts (Taegu Tech. Model WCMX 06T 308). The mean grain size of the powder was about 0.8$\mu$m. Injection molded specimens were debound by solvent extraction and thermal degradation method at various conditions. The specimens were sintered at 140$0^{\circ}C$ for 1 hr in vacuum. Carbon content, weight loss, dimensional change, and macro defects of the specimen were carefully monitored at each stage of the PIM process. PIMed WC-Co milling inserts reached 100% full density after sinteing. Its mechanical properties and micro-structures were comparable with the press and sintered milling insert. Carbon content of the sintered WC-Co insert was mainly determained by the atmosphere of thermal debinding. By controlling powder loading and injection molding condition, dimensional accuracy could be obtained within 0.4%. We confirm that PIM can not only be an alternative manufacturing method for WC-Co parts economically but also provide a design freedom for more effieient cutting tools.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.297-299
• /
• 1999

Effects of additives on the ceramic and electrical properties of Pb(Y$_{1}$2/Ta$_{1}$2/)O$_3$-PbZrO$_3$-PbTiO$_3$ceramics in a perovskite type structure were investigated. The dielectric and piezoelectric properties of the base composition were improved markedly through selection of Fe$_2$O$_3$ additives in proper amounts. The composition Pb(Y$_{1}$2/Ta$_{1}$2/)O$_3$-PbZrO$_3$-PbTiO$_3$ obtained the dielectric constant ($\varepsilon$$_{r}$=1,425). Also, electromechanical couping factors for planar(k$_{p}$) and piezoelectric constant(d$_{33}$) were obtained 0.50 and 294[pC/N] at the additives 0wt% Fe$_2$O$_3$ respectively. The mechanical quality facor(Q$_{m}$) of Pb(Y$_{1}$2/Ta$_{1}$2/)O$_3$-PbZrO$_3$-PbTiO$_3$+Fe$_2$O$_3$(0.3 wt%) is about 510.510.510.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.3 no.2
• /
• pp.176-184
• /
• 1993

The glasses, which the $\beta$-spodumene as the principal crystalline phase could be precipitated, were melted by adding >, $P_2O_5, TiO_2, ZrO_2 in the Li_2O-Al_2O_3-SiO_2$ system. In order to achieve the glass-ceramic body of near-theoritical density by sintering method, the optimum condition of heat treatment, the effect of glass powder size and the properties were investigated by DTA, XRD, bulk density, thermal expansion and SEM. Addition of $P_20_5$ imProved the tendency of sintering and the sample with 9wt% $P_20_5$ content was the most dense OOdy by sintering method. The optimum condition of heat treatmemt was sintered for densitification at $740^{\circ}C$ and crystallized at $950^{\circ}C$. In the optimum condition, the relative density was above 90% and the thermal expansion was negative about $-1{\times}10^{-7}/^{\circ}C$.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.22 no.3
• /
• pp.255-261
• /
• 1993

The effect of dried soymilk residue (DSR) on protein quality of tofu was studied. The amount of added DSR into soybean water extract was corresponding 10% (dry basis) of soybean used in tofu manufacturing. Proximate composition and in vitro protein qualities of soybeans at different stages of the conversion into tofu have also been investigated. Partially substituted tofu with DSR (TDSR) had higher moisture content (80.6%) than that of tofu prepared in traditional manner (TT). TDSR contained lower content of protein (38.9%) and total lipid (26.9%) compared to 45.8% of protein and 34.3% of total lipid for TT. A large amount of trypsin inhibitor (TI) in raw soybeans was diminished and extracted through tofu processing, and only 10~13% of TI in raw soybean remained in both tofu products (TDSR and TT). There was not a considerable difference in amino acid profiles between TT and TDSR, but TDSR had a higher content of lysine than that in TT. in vitro studies showed that TDSR and TT were comparable in terms of both in vitro digestibilities (90% over for four-enzyme digestibility and predicted digestibility) and discriminant computed protein efficiency ratio (2.07~2.14, DC-PER). Unlike those in vitro indices for protein quality, computed protein efficiency ratio (C-PER) of TDSR was much lower (1.4) than that of TT (1.95). It was revealed that C-PERs of tofu products were not in agreement with rat-PERs (1.7~1.9) in previous reports except for TT. However, DC-PER assay was more recommendable for protein quality of tofu products than C-PER assay.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.17 no.2
• /
• pp.109-116
• /
• 1984

In order to assess the protein nutritional quality of salted and dried yellow corvenia, which was prepared using the different salting methods like dry and brine salting, the changes of trypsin indigestible substrate(TI) and in vitro apparent protein digestibility were studied during storage at room temperature($24{\pm}1^{\circ}C$). It was also examined the retention of available lysine and formation of nonenzymatic brown pigments under the same conditions of preparing and storage mentioned above and confirmed the relationship between in vitro digestibility and the antinutritional factors, such as nonenzymatic browning, unavailability of lysine and TI content, TI content was gradually increased during the storage and in showed $1.5{\sim}2$ times more after 57 days storage than at the initial stage which ranged from 0.11 to 0.17mg/g solid. Of all the products, $25\%$ brine salting product contained the least TI content in 0.21 mg/g solid, while $10\%$ dry salting products was the most abundant in 0.30 mg/g solid using Hamerstrand method(1981). In vitro protein digestibility of all dried products was decreased significantly up to 30 days as the contents of TI increased, except $25\%$ brine salted products. After storing for 57 days, the in vitro digestibility was only $4\%$ drip showed in $25\%$ brine salted products. The nonenzymatic brown pigments were also developed on the level of available lysine reduced as in vitro protein digestibility was decreased throughout storage. Of all the various salted and dried products of yellow corvenia, $25\%$ salting product showed the lowest rate of browning development and loss of available lysine. Therefore, it was revealed that unavailability of lysine and development of nonenzymatic brown pigments were major factors influencing the protein quality in salted and dried yellow corvenia.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.4
• /
• pp.589-598
• /
• 1997

The effects of PT/PZ ratio variations in a modified PZT system on crystal structure and electrical properties were studied. $0.05Pb(Sn_{0.5}Sb_{0.5})O_3＋xPbTiO_3＋yPbZrO_3$＋0.4Wt% $MnO_2$(＝0.55PSS＋0.11PT＋0.84PZ＋0.4wt%$MnO_2$ ; x＋y=0.95) systems with variations of PT/PZ from 0.50/0.45 to 0.l1/0.84 were sintered at $1250^{\circ}C$ for 2 hr, and then sintering density, crystal structure, dielctric, piezoelectric, pyroelectic and voltage responsity to infrared were investigated. Sintering density was increased from 7.52g/$\textrm {cm}^3$ to 7.82g/$\textrm {cm}^3$ with increasing PZ content. Dielectric constants at 1 KHz were decreased from 1147 to 193 with variation of PT/PZ from 0.50/0.45 to 0.l1/0.84 after poling of $4 KV_{DC}$/mm at $140^{\circ}C$ for 20 minutes. All Dielectric losses at 1 KHz were less than 1 % in all specimens. $K_{p}$ was increased near to 1 of PT/PZ, and maximun value of 48.2 % was .at 0.45/0.50. Pyroelectric coefficient of PT/PZ with 0.l1/0.84 was maximun value, 0.0541 C/$\m^2$K, and voltage responsity to infrared was 1.5 V.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.989-992
• /
• 2001

(Ba$\sub$0.6-x/Sr$\sub$0.4/Ca$\sub$x/)TiO$_3$(x=0.10, 0.15, 0.20) specimens were fabricated by the solid state reaction method and then the structural and dielectric properties as a function of the composition ratio and sintering temperature were studied. The BSCT(50/40/10) specimen sintered at 1500$^{\circ}C$ showed the highest average grain size(18.25 ${\mu}$m). The Curie temperature and dielectric constant at room temperature decreased with increasing Ca content. The dielectric constant and dielectric loss of the BSCT(50/40/10) specimen, sintered at 1450$^{\circ}C$, were about 4324 and 0.972% at 1KHz, respectively. Dielectric constant at room temperature decreased with increasing an applied field, tunability of the BSCT(50/40/10) sintered at 1300$^{\circ}C$ was 18%.