• 열처리공학회지
• /
• 제9권1호
• /
• pp.53-61
• /
• 1996

Effects of carbon and Ti on damping capacity are investigated in an Fe-17%Mn alloy. The suppressive force of carbon against ${\gamma}{\rightarrow}{\varepsilon}$ transformation increases linearly with an increase in its content, lowering Ms temperature and volume fraction of ${\varepsilon}$ martensite. Carbon deteriorates damping capacity by reducing the interfacial area of damping sources and mobility of the boundaries contributing to anelastic deformation. The reduction in damping capacity is accelerated when carbon-containing alloy is aged at higher temperatures above room temperature. The effect of Ti on damping capacity is found to be benificial in carbon-containing alloy, which is attributed to the depletion of carbon solute due to the formation of TiC.

• 한국재료학회지
• /
• 제10권11호
• /
• pp.732-737
• /
• 2000

$TEMAT/H_2$플라즈마를 이용하여 $TiO_{2\pm}{\delta}$를 증착하였다. Power를 300W에서 500W로 증가시켜 고 밀도 플라즈마를 형성시킨 경우에는 Ti 함유량이 크게 증가하였고, 무시할 정도의 C, N이 함유되었다. 기판에 bias를 가한 경우에도 Ti 양이 증가되면서, 증착률이 크게 증가되었다. 또한 매우 적은 양의 $H_2O(~10^{-4}Torr)$는 TEAMT[tetrakis (ethylmethylamido) titanium] 분해를 효율적으로 이루어 주어 C, N의 양을 크게 감소시키면서 $TiO_2$에 요구되는 충분한 O을 제공하였다. 결과적으로 플라즈마 반응에 의하여 생성된 Ti 양이온이 TiOx 박막형성에 주요한 기여를 하고 있으며, 고 밀도 플라즈마의 사용은 Ti 양이온 생성을 크게 증가시켜 주고, 분위기 중에 존재하는 미량의 수분이 TEMAT 분해 효율성을 크게 하여 $TiO_2$박막증착을 이루고 있다.

• 한국세라믹학회지
• /
• 제40권3호
• /
• pp.229-233
• /
• 2003

By using an oxynitride glass as a sintering additive, the effects of BN content on microstructure and mechanical properties of the hot-pressed and subsequently annealed SiC-BN composites were investigated. The microstructures developed were analyzed by image analysis. The morphology of SiC grains was strongly dependent on BN content in the starting composition. The aspect ratio of SiC decreases with increasing BN content and the average diameter of SiC shows a maximum at 5 wt% BN and decreases with increasing BN content in the starting powder. The fracture toughness increased with increasing BN content while the strength decreased with increasing BN content. The strength and fracture toughness of SiC or SiC-TiC composites were strongly dependent on the morphology of SiC grains, but the strength and fracture toughness of SiC-BN composites were strongly dependent on BN content rather than morphology of SiC grains. These results suggest that fracture toughness of SiC ceramics can be tailored by manipulating BN content in the starting composition. Typical fracture toughness and strength of SiC-10 wt% BN composites were 8 MPa$.$m$\^$1/2/ and 445 MPa, respectively.

• 한국재료학회지
• /
• 제12권8호
• /
• pp.676-681
• /
• 2002

Microstructure, mechanical properties, and oxidation resistance of TiAIN thin films deposited on quenched and tempered STD61 tool steel by arc ion plating were studied using XRD, XPS and micro-balance. The TiAIN film was grown with the (200) orientation. The grain size of TiAIN thin film decreased with increasing Al contents, while chemical binding energy increased with Al contents. When hard coating films were oxidized at $850^{\circ}C$ in air, oxidation resistance of both TiN and TiCN films became relatively lower since the surface of films formed non-protective film such as $TiO_2$. However, oxidation resistance of TiAIN film was excellent because its surface formed protective layer such as $_A12$$O_3$ and $_Al2$$Ti_{7}$$O_{15}$, which suppressed oxygen intrusion.

• International Journal of Korean Welding Society
• /
• 제2권1호
• /
• pp.25-28
• /
• 2002

In the coarse grain HAZ adjacent to the fusion line, most of the TiN particles in conventional Ti added steel are dissolved and austenite grain growth is easily occurred during welding process. To avoid this difficulty, thermal stability of TiN particle is improved by increasing the nitrogen content in steel. In this study, the effect of hlgh nitrogen TiN particle on preventing austenite grain growth in HAZ was investigated. Increased thermal stability of TiN particle is helpful for preventing the austenite grain growth by pinning effect. High nitrogen TiN particle in simulated HAZ were not dissolved even at high temperature such as 1400'E and prevented the austenite grain growth in simulated HAZ. Owing to small austenite grain size in HAZ the width of coarse grain HAZ in high nitrogen TiN steel was decreased to 1/10 of conventional TiN steel. Even high heat input welding, the microstructure of coarse grain HAZ consisted of fine polygonal ferrite and pearlite and toughness of coarse grain HAZ was significantly improved.

• 한국표면공학회지
• /
• 제33권4호
• /
• pp.281-288
• /
• 2000

To understand the effect of Fe on the oxidation behavior of TiAl alloys, TiAl-(2, 4, 6at% )Fe were oxidized at 800 and 90$0^{\circ}C$ in air. The oxidation resistance of TiAl-Fe alloys increased with increasing an iron content. The scales formed consisted of an outer $TiO_2$ layer, an intermediate $A1_2$$O_3$ layer, and an inner mixed ($TiO_2$+$A1_2$$O_3$) layer, being similar to other common TiAl alloys. But, the scales formed on TiAl-Fe alloys were generally thin compared to those formed on pure TiAl, and contained dissolved iron. Below the oxide scale, an oxygen affected zone was formed. This beneficial effects of Fe on increasing the oxidation resistance and scale adherence of TiAl alloys were attributed to the refinement of oxide grains, increased scale adherence and the enhanced alumina-forming tendency.

• 한국재료학회지
• /
• 제11권8호
• /
• pp.708-712
• /
• 2001

($Pb_{0.2}$$Ca_{0.8}$ )[($Ca_{1}$3$Nb_{2}$3/)$_{1-x}$ $Ti_{x}$ ]O$_{3}$ 세라믹스의 $^{4+}$ 치환량 변화에 따른 마이크로파 유전특성을 고찰하였다. $Ti^{4+}$ 치환량이 증가함에 따라 x=0.05부터 x=0.15까지의 조성범위에서는 단일상의 페롭스카이트상을 얻을 수 있었으며, x=0.2이상에서는 $Ti_2$와 $CaNb_2$$O_{6}$ 가 제 2상으로 존재하였고, 결정구조는 x=0.05에서 사방정(orthorhombic) 구조가 x=0.35에서 이방정(cubic) 구조로 전이하였다. 유전상수(K)는 $Ti^{4+}$ 치환량의 증가에 따라 rattling 효과의 증가로 인하여 증가되었으며, B-자리 양이온의 평균이온반겨의 세제곱의 반비례하였다. 그러나 결정립 크기의 감소와 제 2상의 존재로 인하여 Qf값은 감소하였다. $Ti^{4+}$ 치환량이 증가됨에 따리 tolerance factor(t)와 B-자리 결합원자가의 영향으로 공진주파수의 온도계수(TCF)는 -27.36ppm/$^{\circ}C$값으로부터 +18ppm/$^{\circ}C$r값으로 조절되었다. $1350^{\circ}C$d서 3시간 소결한 ($Pb_{0.2}$ $Ca_{0.8}$ )[(Ca$_{1}$3$Nb_{2}$3)$_{1-x}$ /$Ti_{x}$]$O_{3}$ 시편에서 K=51.67, Qf=7268(GHz), TCF=0 ppm/$^{\circ}C$의 우수한 특성을 얻을 수 있었다.

• International Journal of Precision Engineering and Manufacturing
• /
• 제5권1호
• /
• pp.19-26
• /
• 2004

The growth of solid particles in TiC-XC-2vo1.% and TiC-XC-30vo1.% Ni alloys, (where X=Zr, W or Mo) was fitted to the equation of the form $d^3$-${do}^3$=Kt during the liquid phase sintering at 1,673K. Also, the grain growth behavior decreased markedly with the addition of ${MO}_2$C or WC and increased with the addition of zrC. The contiguity was greater in the alloys with a smaller growth rate constant and especially, decreased by increasing the Ni content in the TiC-${MO}_2$C-Ni alloy. In addition, the effect of the addition of carbide on the grain growth of 2 vo1.% Ni alloys was found to be similar to that of 30vo1.% Ni alloys. Consequently, the grain growth mechanism cannot be explained by the usual solution / reprecipitation process, but can be explained in terms of a new growth velocity equation, which includes the effects of contiguous carbide grain boundaries in restricting the overall grain growth, as well as the area of the solid / liquid interface in the alloy.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2008년도 추계학술대회 초록집
• /
• pp.105-106
• /
• 2008

Nanotube morphology change of Ti-Ta-Zr alloy as Zr content increase has been researched using various experimental methods. Ti-Ta-Zr(3, 7 and 15 wt%) alloys were prepared by arc melting and nano-structure controlled for 24 hr at $1000^{\circ}C$ in argon atmosphere. Formation of oxide nanotubes are conducted by anodizing a Ti-Ta-Zr alloy in $H_3PO_4$ electrolytes with small amounts of fluoride ions at room temperature. Electrochemical experiments were carried out with conventional three-electrode configuration with a platinum counter electrode and a saturated calomel reference electrode. The samples were embedded with epoxy resin, leaving a square surface area of $10mm^2$ exposed to the anodizing electrolyte, 1.0M $H_3PO_4$ containing 0.8wt% NaF.

• 한국분말재료학회지
• /
• 제2권2호
• /
• pp.149-157
• /
• 1995

In this study, an attempt was made to fabricate TiAl as well as its in situ composite via combustion synthesis. The processing variable of the combustion synthesis which include aluminum content and the heating rate were found to affect the combustion temperature. The combustion temperature measured, however, was lower than the melting temperature of TiAl and the reaction product were found to include incomplet reaction products. Carbon was added in order to increase the combustion temperature as well as to form in situ reinforcements. The reaction products showed homogeneous microstructures with carbide phases formed within indicating that the addition of carbon increased the combustion temperature above the melting temperature of TiAl.