• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.5
• /
• pp.30-35
• /
• 1993

We have investigated microwave dielectric properties of TiO$_{2}$ added (Pb$_{1-x}$Ca$_{x}$)ZrO$_{3}$ Ceramics with x=0.33, 0.35, and 0.37 sintered at 1400$^{\circ}C$ for 2 h. For additions of up to 3wt% of TiO$_{2}$ in (Pb$_{0.63}$ Ca$_{0.37}$)ZrO$_{3}$ (x=0.37), TiO$_{2}$ was completely soluble in (Pb, Ca)ZrO3 phase and did not affect the grain size of ceramics. Dielectric constant and temperature coefficient of resonant frequency increased due to the formation of solid solution, whereas Q value decreased linearly as TiO$_{2}$ increased up to 1 wt%. However, the dielectric loss was very high as TiO$_{2}$ exceeded 2 wt%. It was also shown that as Ca ion content in 0.5 wt% TiO$_{2}$ added (Pb$_{1-x}$,Ca$_{x}$)ZrO$_{3}$ decreased from x=0.37 to x=0.33, dielectric constant increased and Q value decreased.

• Journal of Korea Foundry Society
• /
• v.23 no.4
• /
• pp.204-211
• /
• 2003

Ti-3wt.%Nb(${\alpha}$type), Ti-20wt.%Nb(${\alpha}+{\beta}$,type) and Ti-40wt.%Nb(${\beta}$type) alloys were melted by vacuum are remelting. The specimens were homogenized at 1050$^{\circ}C$ for 24 hr and were then hot rolled to 50% reduction. Each alloys were solution heat treated at ${\beta}$ zone and ${\alpha}+{\beta}$, zone after homogenization, and then aged. The microstructural and hardness changes in Ti-Nb alloys with Nb contents were investigated by SEM, XRD and hardness tester. The microstructural change from equiaxied to acicular and the increase of ${\beta}$ phase in Ti-Nb alloys were obtained when the Nb content increased. The higher hardness value of ${\alpha}+{\beta}$type alloy was obtained compared to the other alloys.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.2
• /
• pp.125-134
• /
• 2001

($Ti_{1-x}$ $Cr_{x}$ )N coatings were deposited by an ion-plating method in a reactor with two separate metal sources, Ti and Cr. Ti was evaporated using an electron beam, while Cr evaporation was carried out by resistant heating. The Ti and Cr concentrations in the coatings were controlled by the Ti and Cr evaporation ratio. The coating hardness increased with increasing the Cr content(x) and showed a maximum value of 6,000 HK at around x=0.8. The critical load of the coatings, measured by the scratch test, was around 30 N. The wear resistance properties of the ($Ti_{1-x}$$Cr_{ x}$)N coatings were evaluated using a CSEM pin-on-disk type tribometer. A Cr-steel ball as well as a SiC ball, which had hardness values of 590 HK and 2,600 HK respectively, were used as the pin. After the wear test, the surface morphology, roughness and the concentration of the coatings were investigated, with the main focus being on the effect of wear debris and the transferred layer on the wear behavior.

• Journal of Magnetics
• /
• v.21 no.1
• /
• pp.35-39
• /
• 2016

$Cr_{100-x}Ti_x$ amorphous texture-inducing layers (TIL) were investigated to realize highly (002) oriented $L1_0$ FePt-C granular films through hetero-epitaxial growth on the (002) textured bcc-$Cr_{80}Mn_{20}$ seed layer (bcc-SL). As-deposited TILs showed the amorphous phase in Ti content of $30{\leq}x(at%){\leq}75$. Particularly, films with $40{\leq}x{\leq}60$ kept the amorphous phase against the heat treatment over $600^{\circ}C$. It was found that preference of the crystallographic texture for bcc-SLs is directly affected by the structural phase of TILs. (002) crystallographic texture was realized in bcc-SLs deposited on the amorphous TILs ($40{\leq}x{\leq}70$), whereas (110) texture was formed in bcc-SLs overlying on crystalline TILs (x < 30 and x > 70). Correlation between the angular distribution of (002) crystal orientation of bcc-SL evaluated by full width at half maximum of (002) diffraction (FWHM) and a grain diameter of bcc-SL indicated that while the development of the lateral growth for bcc-SL grain reduces FWHM, crystallization of amorphous TILs hinders FWHM. $L1_0$ FePt-C granular films were fabricated under the substrate heating process over $600^{\circ}C$ with having different FWHM of bcc-SL. Hysteresis loops showed that squareness ($M_r/M_s$) of the films increased from 0.87 to 0.95 when FWHM of bcc-SL decreased from $13.7^{\circ}$ to $3.8^{\circ}$. It is suggested that the reduction of (002) FWHM affects to the overlying MgO film as well as FePt-C granular film by means of the hetero-epitaxial growth.

• Applied Chemistry for Engineering
• /
• v.9 no.7
• /
• pp.956-960
• /
• 1998

Cu-Zn and Cu-Zn-Ti catalysts for the steam reforming of methanol were prepared. This reaction was carried out at atmospheric pressure, $250^{\circ}C$, steam/methanol molar ratio 1.5, and contact time 0.1 g-cat.hr/mL-feed. In case of the catalyst with 3 mol% of $TiO_2$, the activity was superior to that of catalysts without $TiO_2$. The reaction products were mainly hydrogen and carbon dioxide. It was found that catalytic activity was not related to specific surface area but affected by metallic copper area which was measured by $N_2O$ decomposition and increased with the addition of $TiO_2$ content. XPS and XRD showed that the oxidation state of zinc was not changed during reaction, but oxidation states of copper existed in Cu(0) or Cu(I).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.12
• /
• pp.929-935
• /
• 2010

$(1-x)BaTiO_3-x(Bi_{0.5}Na_{0.5})TiO_3$ ($0.01{\leq}x{\leq}0.10$) ceramics were fabricated with muffled sintering by a modified synthesis process. Their positive temperature coefficient of resistivity (PTCR) characteristics were investigated systematically. All specimen showed a perovskite structure with a tetragonal symmetry. Both the lattice parameter of a and c axes were slightly decreased with increasing $(Bi_{0.5}Na_{0.5})TiO_3$ (BNT) content. Grain growth was achieved when the incorporated BNT was increased to 6 mol% and the inhibition of grain growth is considered to be due to the appearance of Ba vacancy ($V^{"}_{Ba}$) in the $(1-x)BaTiO_3-x(Bi_{0.5}Na_{0.5})TiO_3$ ($0.08{\leq}x$). With 4 mol% BNT addition, room temperature resistivity decreased to $48 \Omega{\cdot}cm$ and a resistivity jump ($\rho_{max}/\rho_{min}$) was as high as $1.1{\times}10^4$, respectively. Curie temperature was also increased to $171^{\circ}C$ with increasing BNT content.

• Journal of Welding and Joining
• /
• v.34 no.6
• /
• pp.47-54
• /
• 2016

Post-Weld Heat Treatment (PWHT) cracking susceptibility in the weld heat-affected zone (HAZ) of reduced activation ferritic-martensitic (RAFM) steels was evaluated through stress-rupture tests. 9Cr-1W based alloys including different C, Ta and Ti content were prepared. The coarse grained heat-affected zone (CGHAZ) samples were simulated with welding condition of 30 kJ/cm heat input. CGHAZ samples consisted of martensite matrix. Stress rupture experiments were carried out using a Gleeble simulator at temperatures of $650-750^{\circ}C$ and at stress levels of 125-550 MPa, corresponding to PWHT condition. The results revealed that PWHT cracking resistance was improved by Ti addition, i.e., Ti contributed to the formation of fine and stable MX precipitates and suppression of coarse M23C6 carbides, resulting in improvement of stress rupture ductility. Meanwhile, rupture strength increased with increasing solute C content.

• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.2
• /
• pp.150-156
• /
• 1997

The effect of variation of pack activators, compositions, temperature and time on the thickness and structure of aluminide coatings formed on the TiAl alloy was studied in one-step packs and two-step packs containing aluminum for the purpose of improvement of oxidation resistance. The thickness of coating layer was increased with increasing $NH_4Cl$ content up to 3wt% and then it was saturated. Oxidation resistance of coating layers carried out at one step pack was superior to that of ones through of two step pack. The improvement of high temperature oxidation resistance was due to the formation of a protective $Al_2O_3$ surface layers and coating the alloys with $TiAl_3$ phase.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.464-467
• /
• 2002

$TiO_{2}-Co_{3}O_{4}$ humidity sensors were fabricated by conventional ceramic process and their humid sensing characteristics were investigated. The sample which was added 10wt% $Co_{3}O_{4}$ and heat-treated $1200^{\circ}C$ showed the highest sensitivity to humidity changes and improved a linearity. As $Co_{3}O_{4}$ content was increasing, the sensor consists a uniform pore distribution and grain in the surface. This was analyzed by SEM photographs.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1487-1489
• /
• 1994

$(Zr_{0.65}Sn_{0.35})Ti_{1.04}O_4$ system which has a dielectric constant, low dielectric loss and temperature coefficient was investigated. Temperature coefficient varied from positive to negative with increasing of NiO. For the NiO content 1.0wt%. i.e $(Zr_{0.65}Sn_{0.35})Ti_{1.04}O_4$, the ceramic showed very good dielectric properties such as ${\epsilon}$=37.8, $Q{\times}f_o=49.000$ and ${\tau}_r= 4{\pm}1ppm/^{\circ}C$.