• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.44-48
• /
• 1996

We have investigated the influence of Ti/Ba mole ratio in the characteristics of the modified BaTiO$_3$systems with Ca addition. The specimens were fabricated with variations in Ti/Ba mole ratio between 0.995 and 1.01, and sintered in the temperature range between 13$25^{\circ}C$ and 1375$^{\circ}C$. The room temperature resistivity, PTCR effect and ac complex impedence characteristics were studied. It shows that the room temperature resistivity was increased with the increasing Ti/Ba mole ratio and sintering temperature. It was suggested that this result was mainly attributed to its grain-boundary properties

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1257-1261
• /
• 1994

Phsysical and dielectric properties of $(1-x)CaTiO_3-xLa(Zn_{1/2}Ti_{1/2})O_3$ ceramics were investigated at the temperature range of $25^{\circ}C$ to $80^{\circ}C$ at the frequency of 6 GHz. As increasing addition of the amount of $La(Zn_{1/2}Ti_{1/2})O_3$ to x = 5 mol,Q value was increased due to grain growth and increase of density. For more addition, Q value decreased due to electrical defect. Temperature coefficient of resonant frequency could be controlled by the amount of $La(Zn_{1/2}Ti_{1/2})O_3$, which could be explained by volume mixing rule.

• Journal of the Korean Ceramic Society
• /
• v.35 no.3
• /
• pp.287-293
• /
• 1998

The effects of B2O3 addition on the sintering behavior and th microwave dielectric properties of $(Mg_{0.93}Ca_{0.07})TiO_3$ ceramics were investigated. By addition of $B_2O_3$, increases the density of the ceramics increases and grain growth enhances, It was densified to over 94% of $(Mg_{0.93}Ca_{0.07})TiO_3$ theoretical density by the addition of 0.15-1.0wt% B2O3 and stable microwave dielectric properties observed by the addition of 0.2-0.4wt% $B_2O_3.\;(Mg_{0.93}Ca_{0.07})TiO_3$ ceramics sintered at $1200^{\circ}C$ exhibits maximum dielectric constants of 24-25 quality factor($Q{\times}f$) of more than 70000 and temperature coefficient of resonant frequency of $0\;ppm/^{\circ}C$ by adding of 0.15-0.4wt% $B_2O_3$.

• Journal of Powder Materials
• /
• v.29 no.1
• /
• pp.28-33
• /
• 2022

Aluminum-based powders have attracted attention as key materials for 3D printing owing to their low density, high specific strength, high corrosion resistance, and formability. This study describes the effects of TiC addition on the microstructure of the A6013 alloy. The alloy powder was successfully prepared by gas atomization and further densified using an extrusion process. We have carried out energy dispersive X-ray spectrometry (EDS) and electron backscatter diffraction (EBSD) using scanning electron microscopy (SEM) in order to investigate the effect of TiC addition on the microstructure and texture evolution of the A6013 alloy. The atomized A6013-xTiC alloy powder is fine and spherical, with an initial powder size distribution of approximately 73 ㎛ which decreases to 12.5, 13.9, 10.8, and 10.0 ㎛ with increments in the amount of TiC.

• The Korean Journal of Ceramics
• /
• v.5 no.1
• /
• pp.44-49
• /
• 1999

In order to improve the oxidation resistance of $Ti_3Al$, Ti-25at.%Al composites containing dispersed particles of 15wt.%SiC were prepared by a tubular mixing-spark plasma sintering method. The sintered composites had $Ti_3Al$, SiC, $Ti_5Si_3$ and TiC. The presence of $Ti_5Si_3$ and TiC indicates that some of SiC particles reacted with Ti to from more stable phases. From oxidation tests at 800, 900 and $1000^{\circ}C$ under 1 atm of pure oxygen, it was found that the oxidation rate of Ti3Al was effectively reduced by the addition of SiC. The scale was primarily composed of an outer $TiO_2$ layer having some $Al_2O_3 $islands, an intermediate relatively thick $Al_2O_3 $ layer, and an inner $TiO_2+Al_2O_3+SiO_2$ mixed layer. Beneath the scale, Kirkendall voids were seen.

• Journal of Surface Science and Engineering
• /
• v.38 no.3
• /
• pp.106-111
• /
• 2005

Ternary Ti-B-C coatings were synthesized on WC-Co and Si wafers substrates by a PECVD technique using a gaseous mixture of $TiCl_4,\;BCl_3,\;CH_4,\;Ar,\;and\; H_2$. The effects of deposition variables such as substrate temperature, gas ratio, $R_x=[BCl_3/(CH_4+BCl_3)]$ on the microstructure and mechanical properties of Ti-B-C coatings were investigated. From our instrumental analyses, the synthesized Ti-B-C coatings was confirmed to be composites consisting of nanocrystallites TiC, quasi-amorphous TiB2, and amorphous carbon at low boron content, on the contrary, nanocrystallites $TiB_2$, quasi-amorphous TiC, and amorphous carbon at relatively high boron content. The microhardness of the Ti-B-C coatings increased from $\~23 GPa$ of TiC to $\~38 GPa$ of $Ti_{0.33}B_{0.55}C_{0.11}$ coatings with increasing the boron content. The $Ti_{0.33}B_{0.55}C_{0.11}$ coatings showed lower average friction coefficient of 0.45, in addition, it showed relatively better wear behavior compared to other binary coatings of $TiB_2$ and TiC. The microstruture and microhardness value of Ti-B-C coatings were largely depend on the deposition temperature.

• Korean Journal of Materials Research
• /
• v.2 no.6
• /
• pp.436-442
• /
• 1992

When $N_2$was used as shielding gas during the formation of Ti surface-alloyed layer by irradiation of $CO_2$laser beam on steel, TiN and F$e_2$Ti were formed regardness of carbon-content in steel. When Ti content was increased in low carbon-content steel, formation of martensitic structure was suppressed due to increase of critical cooling rate for martensitic transformation. In case of high-carbon steel, even though Ti content was about 1.5% in alloyed layer, hardness was increased by formation of martensitic structure instead of ferrite. In addition to that structure, hardness was incrreased further by precipitation of TiC in Ti alloyed-layer of high carbon-steel.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.298-298
• /
• 2007

Influence of $TiO_2$ on the dielectric properties of the $Bi(Nb_{0.7}Ta_{0.3})O_4$ ceramic with 7 wt% zinc borosilicate(ZBS) glass was investigated as a function of the $TiO_2$ contents with a view to applying this system to LTCC technology. The $Bi(Nb_{0.7}Ta_{0.3})O_4$ ceramic addition of 7 wt% ZBS glass ensured successful sintering below $900^{\circ}C$. But, TCF of $Bi(Nb_{0.7}Ta_{0.3})O_4$ ceramic is large negative values, respectively, it is necessary to adjust to zero TCF for practical applications Therefore, the addition of materials having positive TCF, such as $TiO_2$, might be an effective method for the improvement. In general, increasing addition of $TiO_2$ increased dielectric constant and TCF but it decreased the sinterability and $Q{\tiems}f$ value significantly due to the dielectric property and high sintering temperature of $TiO_2$. $Bi(Nb_{0.7}Ta_{0.3})O_4$ ceramic with 7 wt% ZBS glass and then addition 0.5 wt% $TiO_2$ sintered at $900^{\circ}C$ demonstrated 42 in the dielectric constant(${\varepsilon}_r$), 1,000 GHz in the $Q{\times}f$ value, and $10{\pm}5\;ppm/^{\circ}C$ in the temperature coefficient of resonant frequency(${\tau}_f$).

• Journal of Korea Foundry Society
• /
• v.23 no.2
• /
• pp.63-68
• /
• 2003

Al-Ti-C grain refiner form a relatively new alternative to the existing class of Al-Ti-B type grain refiners for achieving fine equiaxed structures in aluminum alloys during casting and solidification. The present study was carried out to investigate the influence of Al-Ti-C master alloys on the grain structure of Al-7Si alloys. The present study also investigates the relationship between grain refining efficiency and concentrations of Fe and Si in hypo-eutectic Al-Si alloys using Al-3Ti-0.13C master alloys. It is found that several parameters affect significantly the grain refining performance in silumin alloys. The present study reports the influence of various parameters such as alloy content, master alloy addition level, melt holding time and superheat on the grain refining efficiency in Al-7Si alloys.

• Korean Journal of Materials Research
• /
• v.4 no.6
• /
• pp.669-680
• /
• 1994

Oxidation behaviour of TiAl intermetallic compounds with the addition of Cr, V, Si, Mo, or Nb was investigated at 900~$1100^{\circ}C$ under the atmospheric environment. The reaction products were examined by XRD, SEM equipped with WDX. The weight gain by continuous oxidation increased with the addition of Cr or V, but there was less weight gain when Mo, Si or Nb was added individually. he oxidation rate of Cr- or V-added TiAl was always larger than that of TiAI. However, oxidation rate of Si-, Mo- or Nb-added TiAl was almost same or smaller than that of TiAI. Thus, it is concluded that the addition of Cr or V did not improve the oxidation resistance, whereas the addition of Si, Mo or Nb improved the oxidation resistance. Oxides formed on TiAl with Mo, Si, and Nb were found to be more protective, resulting from the decrease in diffusion rate of the alloying elements and oxygen. Nb strengthened the tendency to form $AI_{2}O_{3}$ in the early stage of oxidation, due to the continuous $AI_{2}O_{3}$ layer formation and dense $Tio_{2}+AI_{2}O_{3}$ layer. According to the Pt-marker test of TiAI- 5wt%Nb, oxygen diffused mainly inward while oxides were formed on the substrate surface. Upon thermal cyclic oxidation at $900^{\circ}C$, it is shown that the addition of Cr or Nb improved the adherence of oxide scale to the substrate.