• 열처리공학회지
• /
• 제36권3호
• /
• pp.145-152
• /
• 2023

β titanium alloys containing β stabilizing elements such as V, Nb, Ta, Mo and Fe are widely used etc, due to their excellent specific strength, corrosion resistance, fatigue strength and easy formability. New metastable β titanium alloys are developed containing low-cost elements (Mo and Fe) in this study. Fe element is a strong β-stabilizer which can affect the mechanical and electrochemical properties of Ti-5Mo-xFe (x = 1, 4 wt%) alloys. These properties were analyzed in connection with microstructure and phase distribution. Ti-5Mo-4Fe alloy showed higher compression yield stress and maximum stress than Ti-5Mo-1Fe alloy due to solid-solution hardening and grain refinement hardening effect. As Fe element increased, Fe oxide formation and reduction of ${\bar{Bo}}$ (bond order) value affect the decrease of corrosion resistance. Ti-5Mo-xFe alloys were more excellent than Ti-6Al-4V ELI alloy.

• 열처리공학회지
• /
• 제23권1호
• /
• pp.3-9
• /
• 2010

Titanium and its alloys were brazed in the range of $850-950^{\circ}C$ within 10 min. of brazing time using expensive infra red or other heating methods. However, brazing time needs to be extended to get temperature-uniformity for mass production by using continuous belt type furnace or high vacuum furnace with low heating rate. This study examined effects of holding temperature for 60 min, on microstructure and mechanical properties of titanium alloys. Mechanical properties of titanium alloys were drastically deteriorated with increasing holding temperature followed by grain growth. Maximum holding temperatures for CP (commercial pure) titanium and Ti-6Al-4V were confirmed as $800^{\circ}C$ and $850^{\circ}C$, respectively. Both titanium alloys were successfully brazed at $800^{\circ}C$ for 60 min. with the level of base metal strengths by using Zr based filler metal, $Zr_{54}Ti_{22}Ni_{16}Cu_8$.

• 오토저널
• /
• 제11권6호
• /
• pp.38-47
• /
• 1989

The Finite Element Method has been employed to calculate the effect of particle size, matrix, and volume fractions on the stress-strain relations of .alpha.-.betha. titanium alloys. It was found that for a given volume fraction, the calculated stress-strain curve was higher for a finer particle size than for a coarse particle size within the range of the strains considered, and this behavior was seen for all the different volume fraction alloys considered. The calculated stress-strain curves for three vol. pct .alpha. alloys were compared with their corresponding experimental curve, and in general, good agreement was found.

• 한국재료학회지
• /
• 제9권10호
• /
• pp.1025-1031
• /
• 1999

6종류의 조성을 가진 TiAl계 합금, 즉 Ti-(42, 44)Al-2Nb-4V, Ti-(42, 44)Al-4Nb-2V 및 Ti-(42, 44)Al-4Nb-2Cr을 아크용해법으로 제조한 후, 이들의 산화성질을 조사하였다. 700, 800 및 $900^{\circ}C$의 대기 중, 50시간동안의 등온 및 반복 산화실험으로부터, 산화저항은 Ti-(42, 44)Al-2Nb-4V, Ti-(42, 44)Al-4Nb-2V 및 Ti-(42, 44)Al-4Nb-2Cr의 순으로 증가함을 알 수 있었다. 내산화성에서 V은 해로운 원소이고 Cr은 유익한 원소이었다. 산화 중 모든 모재 구성원서는 외부확산하였고 분위기중으로 부터의 산소는 내부확산하는 상호확산이 관찰되었으며, 생성되는 산화물은 최외각 $\textrm{TiO}_2$층, 상부 ($\textrm{TiO}_2+\textrm{Al}_2\textrm{O}_3$) 혼합층 및 하부 $\textrm{TiO}_2$-잉여층으로 이루어진 3층 산화물구조로 구성되어 있었다.

• Nuclear Engineering and Technology
• /
• 제56권4호
• /
• pp.1480-1489
• /
• 2024

Displacement cascade behaviors of Ti-6Al-4V alloys are investigated using molecular dynamics (MD) simulation. The embedded atom method (EAM) potential including Ti, Al and V elements is modified by adding Ziegler-Biersack-Littmark (ZBL) potential to describe the short-range interaction among different atoms. The time evolution of displacement cascades at the atomic scale is quantitatively evaluated with the energy of primary knock-on atom (PKA) ranging from 0.5 keV to 15 keV, and that for pure Ti is also computed as a comparison. The effects of temperature and incident direction of PKA are studied in detail. The results show that the temperature reduces the number of surviving Frenkel pairs (FPs), and the incident direction of PKA shows little correlation with them. Furthermore, the increasing temperature promotes the point defects to form clusters but reduces the number of defects due to the accelerated recombination of vacancies and interstitial atoms at relatively high temperature. The cluster fractions of interstitials and vacancies both increase with the PKA energy, whereas the increase of interstitial cluster is slightly larger due to their higher mobility. Compared to pure Ti, the presence of Al and V is beneficial to the formation of interstitial clusters and indirectly hinders the production of vacancy clusters.

• Corrosion Science and Technology
• /
• 제8권2호
• /
• pp.62-67
• /
• 2009

Ti and Ti-alloys have good biocompatibility, appropriate mechanical properties and excellent corrosion resistance. However, the widely used Ti-6Al-4V is found to release toxic ions (Al and V) into the body, leading to undesirable long-term effects. Ti-6Al-4V has much higher elastic modulus (100 GPa) than cortical bone (20 GPa). Therefore, titanium alloys with low elastic modulus have been developed as biomaterials to minimize stress shielding. The electrochemical behavior of surface-modified and MC3T3-E1 cell-cultured Ti-30(Nb,Ta) alloys with low elastic modulus have been investigated using various electrochemical methods. Surfaces of test samples were treated as follows: $0.3{\mu}m$ polished; $25{\mu}m$, $50{\mu}m$ and $125{\mu}m$ sandblasted. Specimen surfaces were cultured with MC3T3-E1 cells for 2 days. Average surface roughness ($R_a$) and morphology of specimens were determined using a surface profilometer, OM, and FE-SEM. Corrosion behavior was investigated using a potentiostat(EG&G PARSTAT 2273), and electrochemical impedance spectroscopy was performed (10 mHz to 100 kHz) in 0.9% NaCl solution at $36.5{\pm}1^{\circ}C$. The microstructures of the Ti-30(Ta,Nb) alloys had a needle-like appearance. The $R_a$ of polished Ti-30Ta and Ti-30Nb alloys was lower than that of the sandblasted Ti alloy. Cultured cells displayed round shapes. For polished alloy samples, cells were well-cultured on all surfaces compared to sandblasted alloy samples. In sandblasted and cell-cultured Ti-30(Nb,Ta) alloy, the pitting potential decreased and passive current density increased as $R_a$ increased. Anodic polarization curves of cell-cultured Ti alloys showed unstable behavior in the passive region compared to non-cell-cultured alloys. From impedance tests of sandblasted and cell-cultured alloys, the polarization resistance decreased as $R_a$ increased, whereas, $R_a$ for cell-cultured Ti alloys increased compared to non-cell-cultured Ti alloys.

• 한국공작기계학회논문집
• /
• 제10권6호
• /
• pp.29-35
• /
• 2001

The cutting characteristics of Ti-6Al-4V alloy and total wear when machining Ti-6Al-4V alloy was studied to understand the machining characteristics. This material is one of the strong candidate materials present and future aerospace or met ical applications. Nowadays their usage has already been broaden to commercial applications such as golf club head, finger rings and many decorative items. Anticipating the general use of this material and development of the titanium alloy in domestic facilities, the review and the study of the machining parameters far those alloys are deemed necessary. This study is concentrated to the machining parameters of the Ti-6Al-4V alloy due to their dominant position in the production of tita mum alloys.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2002년도 춘계 학술발표강연 및 논문개요집
• /
• pp.76-76
• /
• 2002

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2001년도 추계학술발표회 초록집
• /
• pp.44-44
• /
• 2001

• 대한치과보철학회지
• /
• 제42권4호
• /
• pp.333-343
• /
• 2004

Statement of problem: In its preceding work, change in surface characteristics were investigated in consideration that both microtopograpy and macroscopic configuration of implants surface are two of the most important factors, in that they can construct agreeable environment by raising surface energy, to affect osseointegration and biocompatibility explained by cell proliferation. Purpose: This study focused on examining cytocompatibility of dental implants materials Ti-Ag alloys, of which mechanical and electrochemical superiority to cp-Ti or Ti6Al4V were verified, in comparison with that of cp-Ti, and Ti6Al4V. Materials and methods: In this regard, MTT tests for L-929, the fibroblast connective tissues and cell proliferation tests for osteoprogenitor cells, MC3T3-E1 were performed on cp-Ti, Ti6Al4V, and Ti-Ag alloys following thermal oxidation according to appropriate heat treatment temperature(untreated, 400, 600, $800^{\circ}C$) and heat treatment duration(untreated, 0.5, 1, 4 hr). Results: The MTT tests on fibroblasts L-929 resulted in cell viability of over 90% in all experimental group entities, where, especially, the 100% of the viability for Ti-Ag alloys specimens accounted for the slightest adverse effect of ions release from those alloys on the cell. In MC3T3-E1 proliferation tests, the population of cells in the experimental group was roughly increased as experimentation proceeded, after two to four days. Proliferation showed highest viability for most of specimens, including Ti2.0Ag, treated at $600^{\circ}C$. Conclusion: In conclusion, it is the heat treatment temperature, not the duration that has considerable effects on thermal oxidation of specimens. Ti-Ag alloys treated at $600^{\circ}C$ proved to have the best surface morphology as well as cytocompatibility when compared with Ti or Ti6Al4V for short-term biocompatibility tests.