• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.348-348
• /
• 2010

Behaviors of $TiO_2$-based photocatalysts with different surface structures on the removal of gas-phase toluene with and without UV irradiation are reported. P-25(Degussa) $TiO_2$ powder dispersed in distilled water by sonication was deposited on the transparent glasses and then dried. Some of the samples were further annealed in oven for 1 hr. These samples obtained before and after annealing were characterized by Brunauer- Emmett-Teller (BET), Transmission Electron Microscope (TEM), X-ray Photoelectron Spectroscopy (XPS) and Fourier Transform Infrared (FT-IR) spectrometry, respectively. Based on BET and TEM data, no significant structural change upon annealing could be identified. However, the sample without annealing showed a significantly higher ability for removing toluene both in the presence and absence of the UV light. XPS and FT-IR results clearly revealed that the population of the OH groups on the surface of $TiO_2$ was higher for the sample without annealing, indicating that the OH groups can enhance the adsorption capacity and photocatalytic activity of $TiO_2$ for the removal of the gas-phase toluene.

• Journal of the Korean Applied Science and Technology
• /
• v.25 no.2
• /
• pp.130-136
• /
• 2008

$xTiO_2$-$ySiO_2$ system photocatalysts were developed by sol-gel method based on the change of production parameters, and their structure of crystallization and the specific surface area were measured. Considering the efficiency of the ethanol and phenol degradation using the catalyst, the conclusions were obtained as follows: By means of X-ray analysis of $xTiO_2$-$ySiO_2$ powder that is obtained from Titanium and Silicon alkoxide by sol-gel process, it is shown that crystal structure of anatase type is a dominating structure and, on the other hand, the structure of rutile also partly exists. The increase of $SiO_2$ contents causes the decrease of the degree of crystallization of the gel, whereas the specific surface area preferentially increases. It is shown that more than 90% of ethanol and phenol are degraded when reaction time is about three and an hours, and the maximum degradation rate of ethanol and phenol is shown in $60TiO_2$-$40SiO_2$ catalyst.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.16 no.5
• /
• pp.216-221
• /
• 2006

An investigation of the influence of $WO_3$ and $V_2O_5$ catalysts on the microstructure, phase formation and selective catalytic reduction (SCR) efficiency of the synthesized SCR powders has been carried out. A commercial anatase-$TiO_2$ was used as the catalysts support. For $WO_3(10wt%)/TiO_2$, the W loading to the $TiO_2$ support led to the lower in anatase to rutile transition temperature from $1200^{\circ}C$ of $TiO_2$ support to ${\sim}900^{\circ}C$. The transition temperature was also lowered to below $650^{\circ}C$ in the $V_2O_5$(5 and 10 wt%) added composition. The $WO_3(10wt%)/TiO_2$ SCR powder obtained at $450^{\circ}C$ showed near 100% of $NO_x$ conversion efficiency at $350{\sim}400^{\circ}C$ and for the powder prepared at $650^{\circ}C$ the same efficiency was achieved in wider temperature range $300{\sim}400^{\circ}C$. The highest $NO_x$ conversion efficiency of 100% was obtained in the $V_2O_5(5wt%)/TiO_2$ SCR composition calcined at $650^{\circ}C$ in the relatively wider temperature range $250{\sim}350^{\circ}C$, while the catalytic efficiency considerably decreased for the $V_2O_5(10wt%)/TiO_2$. The lowered conversion efficiency of $NO_x$ observed in the $V_2O_5(10wt%)/TiO_2$ composition calcined at $650^{\circ}C$ was considered to be correlated with the lowered surface area resulting from the increased crystallite growth by highly reactive vanadium loading.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.10
• /
• pp.3407-3412
• /
• 2012

The Ti incorporation at Fe-site in the double perovskite lattice of $Sr_2FeNbO_6$ (SFNO) system is studied. The Ti concentration optimization yielded an efficient photocatalyst. At an optimum composition of Ti as x = 0.07 in $Sr_2Fe_{1-x}Ti_xNbO_6$, the photocatalyst exhibited 2 times the quantum yield for photolysis of $H_2O$ in presence of $CH_3OH$, than its undoped counterpart under visible light (${\lambda}{\geq}420nm$). Heavily Ti-doped $Sr_2Fe_{1-x}Ti_xNbO_6$ lattice exhibited poor photochemical properties due to the existence of constituent impurity phases as observed in the structural characterization, as well as deteriorated optical absorption. The higher electron-density acquired by n-type doping seem to be responsible for the more efficient charge separation in $Sr_2Fe_{1-x}Ti_xNbO_6$ (0.05 < x < 0.4) and thus consequently displays higher photocatalytic activity. The Ti incorporated structure also found to yield stable photocatalyst.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.5
• /
• pp.217-221
• /
• 2018

Selective laser melting (SLM) technique is one of the additive manufacturing processes, in which functional, complex parts can be directly manufactured by selective melting layers of powder. SLM technique has received great attention due to offering a facile part-manufacturing route and utilizing a hard-to-manufacturing material (e.g. Ti6Al4V). The SLM process allows the accurate fabrication of near-net shaped parts and the significant reduction in the consumption of raw materials when compared to the traditional manufacturing processes such as casting and/or forging. In this study, we focus the high-speed additive manufacturing of Ti6Al4V parts in the aspect of manufacturing time, controlling various process parameters.

• Journal of the Korean Ceramic Society
• /
• v.39 no.6
• /
• pp.535-539
• /
• 2002

In this study photoadsorption propreties of Ag ion in AgNO$_3$ solution by TiO$_2$nanopowder synthesized by homogeneous precipitation process at low temperature were investigated. It was found that the photocatalytic redliction in AgNO$_3$solution was occurred by TiO$_2$nanopowder even under th sun light irradiation, although the reduction of Ag ions was slow with th small adsorption of 9.32 ppm. Notably the Ag adsorption was promoted in th dark condition probably owing to the chestnut bur shape of TiO$_2$ nanopowder itself. In the application of UV the Ag ions were completely adsorbed within 120 min, showing more significant photocatalytic reaction. The measured adsorption reaction rate and adsorption equilibrium rate constants were 0.0004 g/min and 1494.20(120 $m^2$/g), respectively.

• Journal of the Korean Ceramic Society
• /
• v.54 no.1
• /
• pp.23-27
• /
• 2017

A series of $CeO_2-TiO_2$ composite samples with different Ce/Ti molar ratios were prepared by the paper template. Powder X-ray diffraction (XRD) and transmission electron microscopy (TEM) were used to confirm a face-centered cubic lattice of $CeO_2$ with Ce/Ti =8:2 or 9:1 and a two phase mixture of anatase titania and face-centered cubic ceria with Ce/Ti = 7 : 3. The field emission scanning electron microscopy (FESEM) results suggest that the products are micron braid structures consisting of fibers with diameters in a range of $1-6{\mu}m$ and lengths of several hundred micrometers. $N_2$ absorption-desorption testing shows that the composite at Ce/Ti molar fraction of 8 : 2 has the largest BET surface area (about $81m^2{\cdot}g^{-1}$). Compared to the pure $CeO_2$ sample, the composites show superior catalytic activity for $H_2$ reduction and CO oxidation. For the micron braid structure $CeO_2-TiO_2$ composite (Ce/Ti = 8 : 2), due to the high surface area and the solid solution with appropriate $Ti^{4+}$ incorporation, the CO conversion at about $280^{\circ}C$ was above 50% and at $400^{\circ}C$ was 100%.

• Transactions of the Korean hydrogen and new energy society
• /
• v.9 no.2
• /
• pp.65-75
• /
• 1998

Five different processes were selected and tested to find an useful method of manufacturing Fe-Ti type electrode. Initially, FeTi alloy was prepared by melting in plasma arc furnace and then powdered for shaping. Electroless Ni plating on these powder particles before shaping improved the discharge characteristics. The effects of heat-treatments on the electrode characteristics were also investigated. The discharge capacities of electrods were increased with the increasing heat-treatment temperatures. When heat treated at $1000^{\circ}C$ after shaping, the best results were acquired in the discharge capacity and cycle life. Both electroless Ni plating and heat-treatment were appeared to be crucial for the performance improvement of FeTi type electrode. Fe-Ti -Mn electrodes were prepared according to the process suggested in this study and tested to verify the promising effects of that.

• Applied Chemistry for Engineering
• /
• v.7 no.4
• /
• pp.794-801
• /
• 1996

$TiO_2$ fine powders were synthesized via hydrolysis reaction of titanium isopropoxide in isopropanol solvent and the reaction rates were studied by use of UV spectroscopic method. The reactions were controlled to proceed to pseudo-first-order reaction in the presence of excess water in isopropanol solvent. The rate constants which varied with temperature and concentration of water were calculated by Guggenheim method. Reactions using $D_2O$ were also carried out to determine the catalytic character of water. n value of water molecules in transition state and the thermodynamic parameters showed that the reaction proceeded by $S_N2$ mechanism. $TiO_2$ powders synthesized in this reaction were almost spheric forms and had average particle size of $0.3{\mu}m$ diameter.

• Solar Energy
• /
• v.11 no.2
• /
• pp.70-76
• /
• 1991

Electrochemical reaction utilizing the semiconducting photoanodes can be applied to the photoelectrolysis of water to produce hydrogen. In this preliminary experiment, $TiO_2$ photoanodes were prepared by sintering anatase-$TiO_2$ powder at $1,250^{\circ}C$ and thermal oxidizing titanium plate at $850^{\circ}C$ in air and oxygen, respectively. Their surface structures were observed by XRD and optical microscope. I-E characteristics of thermally oxidized $TiO_2$ photoanode were also investigated under illuminated and dark conditions using 1 N and 0.1 N NaOH electrolyte solutions.