• Korean Journal of Materials Research
• /
• v.13 no.5
• /
• pp.338-342
• /
• 2003

Adhesion between Cu and low-k films has been investigated. Low-k films deposited using a mixture of hexamethyldisilane(HMDS) and Para-xylene had a dielectric constant as low as 2.7, showing the thermally stable properties up to $400^{\circ}C$. In this study, Ti glue layer, boron dopant, and $N_2$plasma treatment were used to improve adhesion property of between Cu and low-k films. Ti glue layer slightly improved adhesion property. After $N_2$plasma treatment, the adhesion property was significantly improved due to the increased roughness and the formation of new binding states between Ti and plasma-treated PPpX : HMDS. However, $300^{\circ}C$ annealing of $N_2$plasma treated sample caused the diffusion of Cu into the PPpX : HMDS, degrading the low-k properties. In the case of Cu(B)/Ti/PPpX : HMDS, the adhesion was remarkably increased. This enhanced adhesion was attributed to formation of Ti-boride at the Cu-Ti interface. It is because the formed Ti-boride prevented the diffusion of Cu into the PPpX : HMDS and the Cu-Ti reaction at the Ti interface.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1993.11a
• /
• pp.86-86
• /
• 1993

• Korean Journal of Materials Research
• /
• v.3 no.6
• /
• pp.593-597
• /
• 1993

Adhesion of CVD W to the TiN glue layer in the blanket W process which is a promising candidate for filing contact holes in subhalfmicron ULSIs has been investigated. The adhesion was enhanced with increasing the W film thickness due to the decrease of the TiN film stress. The adhesion strength was increased by the sputter etching of the TiN surface prior to the W deposition owing to the removal of contaminants and the increase of the surface roughness. The adhesion of the W film to the TiN glue layer property was also improved by Ar ion implantation of the TiN surface owing to the activation of the TiN surface.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1992.05a
• /
• pp.70-70
• /
• 1992

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1992.11a
• /
• pp.28-30
• /
• 1992

Long incubation period of W nucleation on the TiN glue layer is a serious problem in blanket W process. In this study we investigated the dependence of W nucleation and growth rate on the preparation method of the TiN film, deposition temperature, chemistry, $SiH_4/WF_6$ ratio and sputter etching, ion implantation, and $SiH_4$ flushing pre-treatments. Incubation periods of W nucleation and deposition rates of W growth on three different TiNs are in the order of TiN>RTP-TiN> annealed TiN and TiN${\leq}$RTP-TiN${\leq}$ annealed TiN, respectively. $\beta$-W is not found on TiN substrate even for high $SiH_4/WF_6$ ratio. Sputter etching pre-treatment increases incubation period of W nucleation, while it decreases deposition rate. $SiH_4$ flushing pre-treatment decreases incubation period, but it slightly decreases deposition rate.

• Korean Journal of Materials Research
• /
• v.3 no.5
• /
• pp.466-475
• /
• 1993

Adhesion of W to TiN which is used as a glue layer in the blanket tungsten process has been investigated using the pulling and scratch methods and analysed using surface roughness measurements by SEM and the reflectivity measurement, the stress measurement and the SIMS depth profiling Significant differences between the adhesion of the CVD tungsten film to the s-TiN and that to the a-TiN were found. It appeared that the fomer were better than the latter, which is due to the facts that the s-TiN film has a rougher surface and a lower stress level and a higher oxygen content than the a-TiN film. Also the ashesion strength was degreaded with increasing the TIN film thickness because of the increase of the TiN film stress.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.403-404
• /
• 2012

We fabricated TFT devices with the GeSe channel. A single device consists of a Pt source and drain, a Ti glue layer and a GeSe chalcogenide channel layer on SiO2/Si substrate which worked as the gate. We confirmed the drain current with variations of gate bias and channel size. The I-V curves of the switching device are shown in Fig. 1. The channel of the device always contains amorphous state, but can be programmed into two states with different threshold voltages (Vth). In each state, the device shows a normal Ovonic switching behavior. Below Vth (OFF state), the current is low, but once the biasing voltage is greater than Vth (ON state), the current increases dramatically and the ON-OFF ratio is high. Based on the experiments, we draw the conclusion that the gate voltage can enhance the drain current, and the electric field by the drain voltage affects the amorphous-amorphous transition. The switching device always contains the amorphous state and never exhibits the Ohmic behavior of the crystalline state.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.280-281
• /
• 2011

We fabricated the devices of TFT type with the amorphous chalcogenide channel. A single device consists of a Pt source and drain, a Ti glue layer and a GeSe chalcogenide channel layer on SiO2/Si substrate which worked as the gate. We confirmed the drain current with variations of gate bias and channel size. The I-V curves of the switching device are shown in Fig. 1. The channel of the device always contains amorphous state, but can be programmed into two states with different threshold voltages (Vth). In each state, the device shows a normal Ovonic switching behavior. Below Vth (OFF state), the current is low, but once the biasing voltage is greater than Vth (ON state), the current increases dramatically and the ON-OFF ratio is about 4 order. Based on the experiments, we contained the conclusion that the gate voltage can enhance the drain current, and the electric field by the drain voltage affects the amorphous-amorphous transition. The switching device always contains the amorphous state and never exhibits the Ohmic behavior of the crystalline state.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.575-578
• /
• 2000

In this work, all solid-state thin film supercapacitor(TFSC) was fabricated using tungsten trioxide (WO$_3$) with a structure WO$_3$/LiPON/WO$_3$/Pt/TiO$_2$/Si (substrate). After TiO$_2$ was deposited on Si(100) wafer by d.c. reactive sputtering, the Pt current collector films were grown on TiO$_2$glue layer without breaking vacuum by d.c. sputtering. Fabrication conditions of WO$_3$ thin film were such that substrate temperature, working pressure, gas ratio of $O_2$/Ar and r.f. power were room temperature, 5 mTorr, 20% (O$_2$(8sccm)/Ar(32sccm)) and 200W, respectively. LiPON electrolyte film were grown on the WO$_3$ film using r.f. magnetron sputtering at room temperature. The XRD pattern of the as-deposited WO$_3$ thin film were shown no crystalline peak (amorphous). The SEM image of as-deposited WO$_3$ thin film showed that the surface is smooth and uniform. The capacitiy of as-fabricated TFSC was 0$\times$10$^{-2}$ F/$\textrm{cm}^2$-${\mu}{\textrm}{m}$.