• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.1
• /
• pp.23-29
• /
• 2001

The effects of Ti-silicide process on the electrical properties of an analog polysilicon capacitor were investigated. To improve the linearity with the applied voltage both electrodes, which are polysilicon in our device, should have almost same material properties. The doping concentrations of both electrodes need to be high and to have the similar levels. Voltage Coefficient of Capacitance (VCC) is one of the properties to represent the linearity of analog capacitor, and it is related with the material and the structure of capacitor. In this study, it was possible to obtain the lower VCC by siliciding the polysilicon areas of capacitor. This is due to the parasitic capacitance at the interfaces between silicide and polysilicons, resulting the decrease of unit capacitance. However, we assumed the creation of positive oxide charge near the lower polysilicon electrode during the silicide process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.260-260
• /
• 2009

In high-efficiency crystalline silicon solar cell, If high-efficiency solar cells are to be commercialized, It is need to develop superior contact formation method and material that can be inexpensive and simple without degradation of the solar cells ability. For reason of plated metallic contact is not only high metallic purity but also inexpensive manufacture. It is available to apply mass production. Especially, Nickel, Copper are applied widely in various electronic manufactures as easily formation is available by plating. Ni is shown to be a suitable barrier to Cu diffusin as well as desirable contact metal to silicon. Nickel monosilicide has been suggested as a suitable silicide due to its lower resistivitym lower sintering temperature and lower layer stress than $TiSi_2$. In this paper, Nickel as a seed layer and diffusion barrier is plated by electroless plating to make nickel monosilicide.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.269-269
• /
• 2009

염료감응형 태양전지는 다공질 $TiO_2$ 전극막, 광감응형 염료, 전해질로 구성된 전기화학적 원리를 이용한 태양전지이다. 전해질은 전자가 빠져나간 염료에 전자를 공급하고 $PtCl_4$로부터 전자를 공급받아 산화/환원 반응을 한다. $PtCl_4$는 하부 기판에서 전자를 전해질에 제공한다. 본 연구에서는 Sealant를 이용하여 전해질의 면적이 효율에 어떤 영향을 미치는지 관찰하였다. AM 1.5 (100 $mW/cm^2$)하에서의 광 에너지로 측정한 효율은 전해질 면적이 1 $cm^2$ 일 때 가장 높은 4.46%의 효율이 나타났다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.434-435
• /
• 2009

The crystalline silicon solar cell where the solar cell market grows rapidly is occupying of about 85% or more. high-efficiency and low cost endeavors many crystalline silicon solar cells. the fabrication processes of high-efficiency crystalline silicon solar cells necessitate complicated fabrication processes and Ti/Pd/Ag contact, however, this contact formation processed by expensive materials. Ni/Cu contact formation is good alternative. in this paper, according to temperature Ni silicide makes, produced Ni/Cu contact solar cell and measured conversion efficiency.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.432-432
• /
• 2009

본 연구에서는 HW-PLD(Hot-walled Pulsed Laser Deposition) 법을 이용하여 ZnO 나노와이어를 $Al_2O_3$ 기판 위에 성장하였다. 성장된 ZnO 나노와이어는 SEM, XRD, PL 분석을 통하여 구조적 특성을 확인하였으며, 성장된 나노와이어를 photolithography 공정을 통하여 FET(Field Effect Transistor)소자를 제작하였다. 제작된 소자의 I-V 특성 측정 결과 Ti/Au 전극과 ZnO nanowire 채널 간에 ohmic 접합이 형성된 것을 확인하였으며 게이트 전압의 증가에 따라 소스와 드레인 사이의 전류가 증가하는 전형적인 n-type FET소자 특성을 나타내었다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.2
• /
• pp.126-130
• /
• 2011

Transparent conductive oxide (TCO) is an important part in the construction of dye-sensitized solar cells (DSCs) because of its low sheet resistance, sufficient light transparent ability and high photoelectrical response as a porous photo-electrode material of DSCs. However, the use of TCO for the two DSC electrodes can result in significant cost increase for the less effective DSCs compared to Si based solar cell. Therefore, the replacement of TCO is required for the commercial production of DSCs. In this study, TCO electrodes are replaced by stainless steel mesh. The 3.44[%] efficiency of the prepared TCO-less DSCs sample was obtained.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.12
• /
• pp.1352-1355
• /
• 2004

We have applied front contact metallization of plated nickel and copper for high efficiency passivated emitter rear contact(PERC) solar cell. Ni is shown to be a suitable barrier to Cu diffusion as well as desirable contact metal to silicon. The plating technique is a preferred method for commercial solar cell fabrication because it is a room temperature process with high growth rates and good morphology. In this system, the electroless plated Ni is utilized as the contact to silicon and the plated Cu serves as the primary conductor layer instead of traditional solution that are based on Ti/Pd/Ag contact system. Experimental results are shown for over 20 % PERC cells with the Plated Ni/Cu contact system for good performance at low cost.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.1
• /
• pp.21-27
• /
• 2015

We propose a fabrication process of a 3-electrode type reflective display and ascertain the realized color panel. The first design is proceeded with basis on Ti electrode for fast panel fabrication, easy align process, and high reflection of a white image. To observe the particle movement at the lower electrodes and optimize the space between electrodes, we design the second patterns, from which we establish a fabrication process with the mixing of electronic ink, loading of this ink, electronic ink assembly, driving, and packaging. After aging process, we ascertain a normally driving panel with black, white, and blue color.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.3 no.2
• /
• pp.77-84
• /
• 1997

For the effective treatment of shipboard sewage continuously, a non-diaphragm electrolytic treatment device using DSA type insoluble electrode, Ti/IrO2, anode and H-C metal cathode, was studied. The most effective electrolytic conditions were obtained when cell clearance, 6mm, pH 5-6 and the concentration of seawater, more than 20% as batch test results. The COD removal rate was varied in logarithmic function, showed as C=Coe-KE and the required current was E = A/QCo [A.min/mgCOD]. When the COD removal effeciency was more than 90%, the electrolytic reaction constant was 0.02.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.2 no.1
• /
• pp.67-75
• /
• 1996

An innovative batch electrolytic system consisted of electrolytic basin, which was equipped with DSA(Dimensionally Stable Anode) type insoluble electrode, Ti/IrO2 anode and H-C metal cathode, and flotation separator was developed for the efficient treatment of shipboard emulsified oily wastewater. The electorod cleance and current density of elecrolytic basin to ensure maximum treatment efficiency of oily wastewater was evaluated as 6 mm, 3 A/dm3, respectively. The electrolytic efficiency of oily wastewater was affected by the operationtemperature, and it means that the temperature controller to ensure the stabiity of the process is required. The conductivity in the electrolytic basin was increased with the percentage of sea water in the oily wastewater, and over 90% of treatment efficiency of oily wastewater could be obtained at 7% of sea water. The oil removal rate was increased according to the increase of the quantity of electricity, and the maximum value of electrilyic rate constant was 288 mgoil/A.min. The information obtained from this study might be used for development of an efficient continuous electrolytic system treating the emulsified oily wastewater.